LM2903YST - Dual 36V Low-Power Comparator | STMicroelectronics
料号: LM2903YST ✓ 量产中LM2903YST 概述
A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its output state according to the polarity of the difference. The LM2903 contains two independent comparator channels. Within the broader semiconductor hierarchy, it is an analog comparator, an interface IC, and a signal-conditioning device commonly used between sensors, switching circuits, and digital control logic.
Key features include a supply current of 0.4 mA that remains independent of supply voltage, low input bias current of 25 nA typical, and low input offset current of ±5 nA typical. The open-collector outputs permit wired-AND connections and require an external pull-up resistor. A typical propagation delay of 1.3 µs supports threshold and switching functions, while the wide supply range accommodates industrial and automotive-style supply conditions.
Each comparator has its own non-inverting input, inverting input, and open-collector output. The channels share the supply and ground pins but remain electrically independent for signal comparison. Operation from a single supply or split dual supplies gives designers flexibility when working with bipolar sensor signals, positive-only rails, or systems whose input range extends close to ground.
Typical uses include sensor threshold detection, battery and power-supply monitoring, industrial control interfaces, automotive signal conditioning, window or level comparisons, and general-purpose logic qualification. The low 0.4 mA supply-current characteristic is particularly useful in continuously powered equipment where every increment of standby current affects system architecture.
Designers should account for the open-collector output when selecting a pull-up resistor and logic supply voltage. Input common-mode limits, output saturation behavior, and the 1.3 µs response time must also be checked against the propagation delay allowed by the surrounding system. The manufacturer datasheet provides the authoritative pin assignments, electrical limits, and test conditions.
This page combines operating limits, package details, comparison data, replacement guidance, and practical design notes to support component selection, schematic review, PCB implementation, and sourcing for the LM2903YST.
直接替换替代料: LM2903YST ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
LM2903DT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2903YD
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2903YST 最大额定值与电气特性
| Comparator Type | 2 independent differential voltage comparators |
| Number of Channels | 2 channels |
| Single Supply Voltage Range | +2 V to +36 V |
| Dual Supply Voltage Range | ±1 V to ±18 V |
| 电源电流 | 0.4 mA typical, independent of supply voltage |
| Comparator Power at 5 V | 1 mW per comparator |
| Input Bias Current | 25 nA typical |
| Input Offset Current | ±5 nA typical |
| Propagation Delay | 1.3 µs typical |
| 输出类型 | Open-collector |
| Common-Mode Input Range | Includes ground |
| 工作温度范围 | -40 °C to +125 °C |
| Automotive Qualification | AEC-Q100 |
| 封装 | 8-pin MiniSO/TSSOP |
| 安装类型 | Surface mount |
LM2903YST 引脚配置
| 引脚 1 | OUT1 — Comparator 1 open-collector output |
| 引脚 2 | IN1- — Comparator 1 inverting input |
| 引脚 3 | IN1+ — Comparator 1 non-inverting input |
| 引脚 4 | GND — Ground connection |
| 引脚 5 | IN2+ — Comparator 2 non-inverting input |
| 引脚 6 | IN2- — Comparator 2 inverting input |
| 引脚 7 | OUT2 — Comparator 2 open-collector output |
| 引脚 8 | VCC — Positive supply connection |
典型应用
LM2903YST 适用于 6 应用s: Industrial Sensor Threshold Detection, Battery and Power-Supply Monitoring, Automotive Signal Conditioning, Window and Level Comparators, Control-System Logic Interface, Portable and Low-Power Monitoring.
Industrial Sensor Threshold Detection
The LM2903YST fits industrial sensor interfaces that convert an analog measurement into a digital switching event. Each independent comparator can compare a sensor signal against a reference, while the 25 nA typical input bias current limits disturbance of high-impedance sensing paths. Its 2 V to 36 V single-supply range supports operation from low-voltage sensor rails through higher industrial supply levels. The 1.3 µs typical propagation delay is suitable for general threshold and alarm functions. Because the outputs are open collector, pull-up resistors can establish the logic voltage independently, allowing the comparator channels to drive a different logic domain from the analog supply when the interface permits it.
推荐
Battery and Power-Supply Monitoring
The LM2903YST can supervise a battery-backed rail or supply node by comparing its voltage with a reference threshold and producing an open-collector status indication. The 2 V to 36 V operating range accommodates multiple battery and industrial supply arrangements, while 0.4 mA typical supply current reduces continuous monitoring overhead. Two independent channels allow simultaneous supervision of a main rail and a backup or auxiliary rail. The pull-up resistor on each output defines the status-logic voltage, and the 1.3 µs typical response allows rapid reaction to threshold crossings. Designers should confirm the precise common-mode limits before sensing near the negative rail under dual-supply operation.
推荐
Automotive Signal Conditioning
The LM2903YST is suitable for automotive threshold and signal-conditioning circuits requiring a dual comparator, broad supply range, and qualified temperature behavior. AEC-Q100 qualification and operation from -40 °C to +125 °C distinguish it from generic consumer-grade alternatives. The two channels can independently monitor different inputs, including sensor signals, switch states, or supply-derived thresholds. Open-collector outputs provide flexible wired-AND arrangements and selectable pull-up voltages, but the external pull-up network must preserve adequate rise time in the connected logic circuit. Designers should review input protection and transient requirements separately from the comparator's static operating limits.
推荐
Window and Level Comparators
The LM2903YST is well suited to window-limit and level-detection functions because it provides two independent channels with complementary input connections for each comparison. For example, one channel can detect a signal crossing an upper reference while the other detects a lower boundary. The 25 nA typical input bias current is beneficial when the monitored voltage comes from a high-impedance divider, and the 0.4 mA typical supply current supports low-power monitoring. Open-collector outputs allow both channels to be pulled up to a common logic rail or combined for a wired-AND fault indication. Timing components should be placed so the circuit remains stable around the switching threshold.
推荐
Control-System Logic Interface
The LM2903YST can bridge slowly varying or noisy analog control signals to digital logic in industrial equipment. One comparator channel may translate a feedback voltage into a logic state, while the second supports an auxiliary limit or alarm function. Its low 0.4 mA typical supply current is advantageous in systems that remain powered continuously. The open-collector output can sink the required logic current and requires an external pull-up, which lets the output voltage be matched to the receiving circuit. Engineers should verify output sink-current limits, pull-up resistance, and the resulting RC rise time before using it with high-speed buses or heavily capacitive nodes.
推荐
Portable and Low-Power Monitoring
The LM2903YST supports compact, continuously powered monitoring systems because its supply current is 0.4 mA typical and remains independent of supply voltage. It can monitor charger status, battery transitions, or a divided system rail while the two channels provide independent decisions. The 2 V minimum single-supply voltage is useful in low-energy designs, and the 36 V maximum expands applicability to higher-voltage systems. Open-collector outputs reduce the number of required logic rails because an external resistor can connect them to the host's appropriate pull-up voltage. Leakage through the pull-up network should be included in the complete power budget because it adds to the comparator's 0.4 mA consumption.
推荐
推荐产品汇总
工程参考数据: LM2903YST ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2903DT | LM2903YD | LM2903PWR |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Package | 8-pin MiniSO/TSSOP | 8-pin MiniSO/TSSOP | 8-pin MiniSO/TSSOP | 8-pin MiniSO/TSSOP |
| Comparator Channels | 2 independent channels | 2 independent channels | 2 independent channels | 2 independent channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector |
| Single-Supply Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
| Dual-Supply Range | ±1 V to ±18 V | ±1 V to ±18 V | ±1 V to ±18 V | ±1 V to ±18 V |
关键差异点
- Combines dual comparators with automotive qualification (对比 LM2903PWR)
- Wide operating supply supports industrial and battery-related rails (对比 LM2903DT)
- Low supply current independent of supply voltage (对比 LM2903YD)
设计说明
Do not treat the open-collector outputs as actively driven logic outputs. Connect a suitable pull-up resistor from each OUT pin to the intended logic supply, and verify that the output voltage at the maximum sink current and temperature remains compatible with the receiving device. If both outputs are tied together for a wired-AND function, ensure that the pull-up network can support the combined sink current.
Choose the pull-up resistor to balance low power consumption against rise time. Estimated: with a 10 kΩ pull-up and 100 pF total node capacitance, the RC time constant is 1 µs and the 10% to 90% rise time is approximately 2.2 µs. Confirm that this transition is acceptable for the connected logic and add hysteresis where noise near the threshold could cause repeated switching.
The LM2903YST has a 2 V minimum single-supply voltage, but the input common-mode range and output behavior must also be valid at the chosen rail. For dual-supply operation, keep the total supply span within the ±1 V to ±18 V range and avoid forcing either input outside its specified common-mode limits. Review input bias-current error when sensing through a high-value divider.
Place input traces away from switching nodes and route the two comparator channels to minimize shared pickup. Keep the ground connection short and provide a solid ground reference beneath the device where layout permits. External pull-up resistors should be positioned close to the corresponding output pins, while input-divider components should be placed close to the input nodes to reduce leakage and capacitance effects.
Confirm the exact ordering code before approving a board because temperature grade, qualification, package, and shipping form are encoded in the MPN. The LM2903YST is an automotive-qualified 8-pin MiniSO/TSSOP device; do not substitute a DIP-8 or SOIC-8 variant solely because the comparator functions are similar. A mechanical footprint mismatch requires PCB changes.
合规信息
AEC-Q100 qualification is stated in the manufacturer datasheet. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product or material declaration.