LM2904M/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments
料号: LM2904M/NOPB ✓ 量产中LM2904M/NOPB 概述
An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify differences between voltages applied to its inverting and non-inverting inputs. A dual operational amplifier contains two amplifier sections in one package, reducing board area and simplifying designs that require two independent gain stages. Within the broader semiconductor hierarchy, the LM2904 is an amplifier IC, then an operational amplifier, and finally a general-purpose analog building block for instrumentation, control, and signal-conditioning systems.
Key characteristics include a 26 V maximum supply rating, a 700 kHz gain-bandwidth product, low-power operation, internally compensated frequency response, and operation across single- and split-supply arrangements. These features make the LM2904M/NOPB appropriate for transducers, low-frequency analog filters, sensor amplifiers, and general feedback-control circuits. The manufacturer describes the device as a dual low-power, high-gain operational amplifier specifically designed for single-supply operation over a wide range of voltages.
Internally, each amplifier section uses frequency compensation to provide stable closed-loop operation without requiring an external compensation network. The two sections are independent, allowing them to serve separate signal paths or to work together as stages within a larger analog circuit. The 700 kHz gain-bandwidth product favors low-frequency rather than high-speed signal applications, while the 26 V supply rating provides useful headroom for industrial and automotive-style supply environments when the complete circuit satisfies the device ratings.
Typical uses include amplifying outputs from sensors, buffering potentiometer and resistive-divider signals, implementing active low-pass or high-pass filters, and closing loops around slow analog control systems. Two amplifiers in one 8-pin SOIC can also form instrumentation-style signal-conditioning chains when the required common-mode range, output swing, and noise performance match the application.
For PCB design, verify the exact pin orientation and exposed or non-exposed package details against the manufacturer pin configuration before routing copper. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and use a stable local supply-decoupling arrangement. Avoid designs requiring the high slew rate and wide bandwidth of precision or high-speed amplifiers; the LM2904 is better suited to economical, general-purpose low-frequency analog functions.
This product page consolidates the manufacturer family specifications, verified distributor identification, same-footprint alternatives, application guidance, and practical design considerations. It supports faster part identification while keeping datasheet verification, footprint review, and application-specific validation at the center of every engineering decision.
直接替换替代料: LM2904M/NOPB ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2904M/NOPB (相同外形与封装尺寸) ——差异在于 Package, Operating Temperature Range, Slew Rate, Amplifier Type, Number of Amplifiers.
LM2904QD
✅ 直接替换联系询价
查看数据手册 →LM2904-N
✅ 直接替换📋 参考替代料(不在目录中)
LM2904BIDR
✅ 直接替换联系询价
查看数据手册 →LM2904M/NOPB 最大额定值与电气特性
| Amplifier Type | 2-circuit operational amplifier |
| Number of Amplifiers | 2 units |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Operating Supply Type | Single or split supply |
| 工作温度范围 | -40 °C to +85 °C |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Frequency Compensation | Internally compensated |
LM2904M/NOPB 8-pin soic 引脚配置指南
LM2904M/NOPB(8-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM2904M/NOPB.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM2904M/NOPB 适用于 6 应用s: Industrial Sensor Signal Conditioning, Transducer and Instrumentation Amplification, Active Low-Frequency Filtering, Power-Supply Ripple Filtering, Audio-Band Signal Conditioning, Portable Battery-Powered Analog Systems.
Industrial Sensor Signal Conditioning
The LM2904M/NOPB is suitable for conditioning low-frequency industrial sensor signals because each of its two internally compensated amplifiers can buffer or amplify a voltage generated by resistive dividers, transducers, or switches. Its 700 kHz gain-bandwidth product supports moderate closed-loop bandwidth without the complexity of an external compensation network, while the 26 V supply rating accommodates suitably protected industrial supply rails. A practical arrangement uses one section for level shifting or gain, and the other for filtering or output buffering. Designers should verify that the sensor signal remains inside the input common-mode range and that the selected gain does not compromise closed-loop stability.
推荐
Transducer and Instrumentation Amplification
LM2904M/NOPB can form the first two stages of a discrete instrumentation signal chain when its 700 kHz bandwidth and internally compensated response suit the measurement bandwidth. One amplifier may convert a transducer output to a mid-supply reference voltage, while the second provides gain or drives a subsequent measurement stage. This arrangement avoids requiring two separate packages and can improve board utilization. The principal constraint is common-mode and output-range behavior: signal excursions must remain inside the amplifier's specified input and output limits, and resistor tolerances will contribute directly to overall measurement accuracy.
推荐
Active Low-Frequency Filtering
The LM2904M/NOPB is well suited to first- and second-order active filters operating well below its 700 kHz gain-bandwidth product. Two amplifier sections can implement Sallen-Key, multiple-feedback, or buffered active-filter arrangements for power-supply ripple attenuation, sensor smoothing, or audio-band shaping. Internal frequency compensation simplifies closed-loop realization, but component ratios and op-amp noise gain still determine the actual response. Validate gain tolerances, input slew requirements, and output drive against the intended frequency range, and use the manufacturer characteristic data to assess distortion at the required signal level.
推荐
Power-Supply Ripple Filtering
LM2904M/NOPB can buffer a sensitive analog node or provide active filtering after a power converter when ripple remains within the amplifier's bandwidth and output-swing limits. Its 26 V supply capability is useful when the signal path operates from a higher-voltage rail, while the 700 kHz gain-bandwidth product can attenuate ripple components within the closed-loop passband. The two channels allow simultaneous filtering or buffering of related rails. Designers should avoid using the amplifier beyond its output-current and output-voltage limits, and should account for the noise and DC error introduced by feedback resistors when calculating usable filtering performance.
推荐
Audio-Band Signal Conditioning
The LM2904M/NOPB can perform low-frequency audio signal conditioning, including input buffering, gain adjustment, and active equalization within its 700 kHz bandwidth capability. Its dual-amplifier configuration permits left and right channel processing in a compact board area, provided each channel operates within the same supply and loading conditions. The part is appropriate for cost-sensitive general-purpose audio paths rather than demanding low-noise mastering equipment. Designers should review output swing, slew-rate behavior, channel matching, and distortion characteristics against the signal amplitude and load, particularly when driving a low-impedance output stage.
推荐
Portable Battery-Powered Analog Systems
LM2904M/NOPB is appropriate for battery-powered analog systems that need two general-purpose amplifier functions without the higher bandwidth and quiescent demand of a high-speed amplifier family. Single-supply operation simplifies the system architecture, and the dual package reduces component count for gain, buffer, and filtering stages. Low-power behavior is especially useful in portable equipment where supply energy is constrained. The designer must still verify the minimum operating supply, output-swing headroom, input common-mode range, and quiescent current for the exact temperature and grade, since the device is not a rail-to-rail precision amplifier.
推荐
推荐产品汇总
工程参考数据: LM2904M/NOPB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2904QD | LM2904-N | LM2904B | LM2904M |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Count | 2 | 2 | 2 | 2 | 2 |
关键差异点
- Retains the established 700 kHz bandwidth class (对比 LM2904-N)
- Established Texas Instruments LM2904 family sourcing (对比 LM2904M)
- Two general-purpose amplifiers in one compact package (对比 LM2902M)
设计说明
Route each amplifier's input and feedback components directly to its corresponding SOIC pins, and place local supply bypass capacitance at the device power and ground pins. High-impedance inputs should have minimal surrounding copper and a short, low-impedance ground return. Because dual amplifier packages repeat familiar functions but may assign them to different pin numbers, create the schematic around the manufacturer pin table rather than a generic eight-pin dual-op-amp drawing.
Do not assume rail-to-rail input or output behavior. Before finalizing a single-supply circuit, verify that the signal stays within the input common-mode range and that the required output level remains inside the output-swing limits, including temperature and load effects. Also check the selected closed-loop noise gain against the 700 kHz gain-bandwidth product; a high-gain stage may need additional bandwidth analysis even though the amplifier is internally compensated.
For low-frequency precision filtering, use suitable resistor and capacitor tolerances and keep the feedback network physically compact to reduce parasitic capacitance and thermal effects. The two amplifier sections are useful for filtering a signal and then buffering the result, but cascaded closed-loop bandwidth can reduce usable gain. Validate the complete signal chain with the actual source impedance and load rather than relying only on the nominal 700 kHz device bandwidth.
合规信息
The NOPB ordering suffix indicates a lead-free package configuration, but no explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement is available in the manufacturer information used for this page. Confirm the current declarations and qualification status in the Texas Instruments LM2904 product documentation.