LM2904M/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments
MPN: LM2904M/NOPB ✓ 啟用中LM2904M/NOPB 概覽
An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify differences between voltages applied to its inverting and non-inverting inputs. A dual operational amplifier contains two amplifier sections in one package, reducing board area and simplifying designs that require two independent gain stages. Within the broader semiconductor hierarchy, the LM2904 is an amplifier IC, then an operational amplifier, and finally a general-purpose analog building block for instrumentation, control, and signal-conditioning systems.
Key characteristics include a 26 V maximum supply rating, a 700 kHz gain-bandwidth product, low-power operation, internally compensated frequency response, and operation across single- and split-supply arrangements. These features make the LM2904M/NOPB appropriate for transducers, low-frequency analog filters, sensor amplifiers, and general feedback-control circuits. The manufacturer describes the device as a dual low-power, high-gain operational amplifier specifically designed for single-supply operation over a wide range of voltages.
Internally, each amplifier section uses frequency compensation to provide stable closed-loop operation without requiring an external compensation network. The two sections are independent, allowing them to serve separate signal paths or to work together as stages within a larger analog circuit. The 700 kHz gain-bandwidth product favors low-frequency rather than high-speed signal applications, while the 26 V supply rating provides useful headroom for industrial and automotive-style supply environments when the complete circuit satisfies the device ratings.
Typical uses include amplifying outputs from sensors, buffering potentiometer and resistive-divider signals, implementing active low-pass or high-pass filters, and closing loops around slow analog control systems. Two amplifiers in one 8-pin SOIC can also form instrumentation-style signal-conditioning chains when the required common-mode range, output swing, and noise performance match the application.
For PCB design, verify the exact pin orientation and exposed or non-exposed package details against the manufacturer pin configuration before routing copper. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and use a stable local supply-decoupling arrangement. Avoid designs requiring the high slew rate and wide bandwidth of precision or high-speed amplifiers; the LM2904 is better suited to economical, general-purpose low-frequency analog functions.
This product page consolidates the manufacturer family specifications, verified distributor identification, same-footprint alternatives, application guidance, and practical design considerations. It supports faster part identification while keeping datasheet verification, footprint review, and application-specific validation at the center of every engineering decision.
直接替換替代品,適用於 LM2904M/NOPB — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904M/NOPB (相同外形與佔位) — 差異在於 Package, Operating Temperature Range, Slew Rate, Amplifier Type, Number of Amplifiers.
LM2904QD
✅ 直接替換聯絡詢價
查看資料表 →LM2904-N
✅ 直接替換📋 參考替代品(不在目錄中)
LM2904BIDR
✅ 直接替換聯絡詢價
查看資料表 →LM2904M/NOPB 最大額定值與電氣特性
| Amplifier Type | 2-circuit operational amplifier |
| Number of Amplifiers | 2 units |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Operating Supply Type | Single or split supply |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Frequency Compensation | Internally compensated |
LM2904M/NOPB 8-pin soic 腳位配置指南
LM2904M/NOPB(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2904M/NOPB.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2904M/NOPB 適用於 6 應用s: Industrial Sensor Signal Conditioning, Transducer and Instrumentation Amplification, Active Low-Frequency Filtering, Power-Supply Ripple Filtering, Audio-Band Signal Conditioning, Portable Battery-Powered Analog Systems.
Industrial Sensor Signal Conditioning
The LM2904M/NOPB is suitable for conditioning low-frequency industrial sensor signals because each of its two internally compensated amplifiers can buffer or amplify a voltage generated by resistive dividers, transducers, or switches. Its 700 kHz gain-bandwidth product supports moderate closed-loop bandwidth without the complexity of an external compensation network, while the 26 V supply rating accommodates suitably protected industrial supply rails. A practical arrangement uses one section for level shifting or gain, and the other for filtering or output buffering. Designers should verify that the sensor signal remains inside the input common-mode range and that the selected gain does not compromise closed-loop stability.
推薦
Transducer and Instrumentation Amplification
LM2904M/NOPB can form the first two stages of a discrete instrumentation signal chain when its 700 kHz bandwidth and internally compensated response suit the measurement bandwidth. One amplifier may convert a transducer output to a mid-supply reference voltage, while the second provides gain or drives a subsequent measurement stage. This arrangement avoids requiring two separate packages and can improve board utilization. The principal constraint is common-mode and output-range behavior: signal excursions must remain inside the amplifier's specified input and output limits, and resistor tolerances will contribute directly to overall measurement accuracy.
推薦
Active Low-Frequency Filtering
The LM2904M/NOPB is well suited to first- and second-order active filters operating well below its 700 kHz gain-bandwidth product. Two amplifier sections can implement Sallen-Key, multiple-feedback, or buffered active-filter arrangements for power-supply ripple attenuation, sensor smoothing, or audio-band shaping. Internal frequency compensation simplifies closed-loop realization, but component ratios and op-amp noise gain still determine the actual response. Validate gain tolerances, input slew requirements, and output drive against the intended frequency range, and use the manufacturer characteristic data to assess distortion at the required signal level.
推薦
Power-Supply Ripple Filtering
LM2904M/NOPB can buffer a sensitive analog node or provide active filtering after a power converter when ripple remains within the amplifier's bandwidth and output-swing limits. Its 26 V supply capability is useful when the signal path operates from a higher-voltage rail, while the 700 kHz gain-bandwidth product can attenuate ripple components within the closed-loop passband. The two channels allow simultaneous filtering or buffering of related rails. Designers should avoid using the amplifier beyond its output-current and output-voltage limits, and should account for the noise and DC error introduced by feedback resistors when calculating usable filtering performance.
推薦
Audio-Band Signal Conditioning
The LM2904M/NOPB can perform low-frequency audio signal conditioning, including input buffering, gain adjustment, and active equalization within its 700 kHz bandwidth capability. Its dual-amplifier configuration permits left and right channel processing in a compact board area, provided each channel operates within the same supply and loading conditions. The part is appropriate for cost-sensitive general-purpose audio paths rather than demanding low-noise mastering equipment. Designers should review output swing, slew-rate behavior, channel matching, and distortion characteristics against the signal amplitude and load, particularly when driving a low-impedance output stage.
推薦
Portable Battery-Powered Analog Systems
LM2904M/NOPB is appropriate for battery-powered analog systems that need two general-purpose amplifier functions without the higher bandwidth and quiescent demand of a high-speed amplifier family. Single-supply operation simplifies the system architecture, and the dual package reduces component count for gain, buffer, and filtering stages. Low-power behavior is especially useful in portable equipment where supply energy is constrained. The designer must still verify the minimum operating supply, output-swing headroom, input common-mode range, and quiescent current for the exact temperature and grade, since the device is not a rail-to-rail precision amplifier.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904M/NOPB — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904QD | LM2904-N | LM2904B | LM2904M |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | onsemi |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Count | 2 | 2 | 2 | 2 | 2 |
主要差異化特點
- Retains the established 700 kHz bandwidth class (對比LM2904-N)
- Established Texas Instruments LM2904 family sourcing (對比LM2904M)
- Two general-purpose amplifiers in one compact package (對比LM2902M)
設計說明
Route each amplifier's input and feedback components directly to its corresponding SOIC pins, and place local supply bypass capacitance at the device power and ground pins. High-impedance inputs should have minimal surrounding copper and a short, low-impedance ground return. Because dual amplifier packages repeat familiar functions but may assign them to different pin numbers, create the schematic around the manufacturer pin table rather than a generic eight-pin dual-op-amp drawing.
Do not assume rail-to-rail input or output behavior. Before finalizing a single-supply circuit, verify that the signal stays within the input common-mode range and that the required output level remains inside the output-swing limits, including temperature and load effects. Also check the selected closed-loop noise gain against the 700 kHz gain-bandwidth product; a high-gain stage may need additional bandwidth analysis even though the amplifier is internally compensated.
For low-frequency precision filtering, use suitable resistor and capacitor tolerances and keep the feedback network physically compact to reduce parasitic capacitance and thermal effects. The two amplifier sections are useful for filtering a signal and then buffering the result, but cascaded closed-loop bandwidth can reduce usable gain. Validate the complete signal chain with the actual source impedance and load rather than relying only on the nominal 700 kHz device bandwidth.
合規資訊
The NOPB ordering suffix indicates a lead-free package configuration, but no explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement is available in the manufacturer information used for this page. Confirm the current declarations and qualification status in the Texas Instruments LM2904 product documentation.