LM2904WHD - Low-Power Dual Op Amp | STMicroelectronics
料号: LM2904WHD ✓ 量产中LM2904WHD 概述
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. In voltage-following operation, the circuit presents high input impedance and low output impedance, making it useful for buffers, sensor interfaces, and active filtering. The LM2904 belongs to the broader operational-amplifier hierarchy, which includes general-purpose amplifiers, precision amplifiers, instrumentation amplifiers, and comparators.
The LM2904WHD provides two amplifier channels in one package, reducing component count and board area compared with two separate single amplifiers. Its internally frequency-compensated design simplifies closed-loop use in non-inverting, inverting, summing, and feedback configurations. The device is specified as a low-power dual operational amplifier and operates from a single positive power supply, allowing it to interface with low-voltage sensors and control circuitry without a negative supply rail.
The 8-SOIC package provides a standard surface-mount footprint suitable for conventional PCB assembly. Because both amplifiers share the same IC, careful layout should keep sensitive input and feedback paths short, maintain stable ground references, and separate the device from high-current switching stages where practical. Stable operation also depends on following the manufacturer recommendations for bypass capacitance, load conditions, output swing, and input common-mode range.
Typical uses include industrial sensor conditioning, automotive control modules, battery-powered instrumentation, current-loop interfaces, active filters, and general signal amplification. The dual-channel configuration is particularly useful when a board needs one channel for amplification and the other for buffering, offset correction, or active filtering. The low-power nature of the family also makes it suitable for systems where continuous amplifier quiescent current affects thermal design or battery life.
For PCB implementation, place the supply bypass capacitor close to the power pin and connect the decoupling return directly to the appropriate ground plane. Check the datasheet limits for input common-mode voltage, output current, supply voltage, and input offset before fixing the operating point. Avoid relying on output saturation as a substitute for proper supply design, and verify the closed-loop gain-bandwidth and stability margin for the intended feedback network.
This product page combines the LM2904WHD device description, verified manufacturer and distributor references, package-level design guidance, application analysis, and clearly qualified replacement information. It is intended to accelerate component identification while preserving the need to validate electrical compatibility in the final system.
直接替换替代料: LM2904WHD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM2904WHD (相同外形与封装尺寸) ——差异在于 Amplifier Type, Number of Channels, Operating Temperature Range, Package.
LM2904BA
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM2904BIDR
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM2904WHD 最大额定值与电气特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 2 channels |
| Number of Independent Amplifiers | 2 independent amplifiers |
| 输出类型 | Single-ended |
| Frequency Compensation | Internally frequency-compensated |
| Supply Configuration | Single positive supply |
| Power Class | Low power |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| Datasheet Document Length | 11 pages |
LM2904WHD 8-pin soic 引脚配置指南
LM2904WHD(8-pin soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM2904WHD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM2904WHD 适用于 6 应用s: Industrial Sensor Signal Conditioning, Automotive Control Module Signal Conditioning, Battery-Powered Instrumentation, Active Filter and Signal Conditioning, Current Loop Interface, General-Purpose Analog Buffering.
Industrial Sensor Signal Conditioning
The LM2904WHD fits industrial sensor interfaces because it combines two independent, internally frequency-compensated amplifiers with low-power operation from a single positive supply. One channel can amplify the sensor output while the second buffers the result or drives an active filter. The 8-SOIC package reduces board area compared with two separate single amplifiers. Designers should confirm that the sensor output remains within the input common-mode range and that the required gain fits the amplifier's bandwidth and stability characteristics.
推荐
Automotive Control Module Signal Conditioning
LM2904WHD can support automotive and industrial control modules because the STMicroelectronics family is designed for those application categories and combines two amplifier channels in one 8-SOIC package. A channel pair can condition a sensor input and monitor an actuator-related voltage, reducing component count. The exact grade's temperature range, AEC-Q100 status, supply limits, and common-mode window must be confirmed before production release, particularly for safety- or reliability-critical functions.
推荐
Battery-Powered Instrumentation
The LM2904WHD's low-power dual-amplifier architecture is appropriate for battery-powered instrumentation where both circuit area and continuous supply demand matter. The two independent channels can provide measurement amplification and output buffering within a compact 8-SOIC footprint. Because battery systems often have narrow voltage ranges, the supply, input common-mode, and output-swing requirements must be checked across the full battery discharge profile. High source impedance can also make input bias current relevant to measurement accuracy.
推荐
Active Filter and Signal Conditioning
The LM2904WHD is suitable for active filtering because its two internally frequency-compensated channels can implement related amplifier and buffering stages in one package. A common design uses one channel with resistive and capacitive feedback to establish the filter response while the other provides low-impedance drive or gain compensation. Layout quality is important: keep feedback components and input nodes compact, use a stable ground reference, and verify phase margin for the selected topology and load.
推荐
Current Loop Interface
LM2904WHD can be used in current-loop interface and feedback circuits where a second amplifier stage helps drive or buffer an analog signal. Its internally frequency-compensated configuration supports conventional closed-loop operation from a single positive supply. The output must remain inside the specified voltage swing, and the external compensation or feedback network must preserve stability at the target gain. For 4–20 mA process-control loops, confirm the loop direction, input range, and output compliance before implementation.
推荐
General-Purpose Analog Buffering
LM2904WHD is useful for general-purpose buffering when a design needs more than one buffered analog output. Each channel can follow a reference or conditioned sensor node, while the dual configuration avoids adding a second single-amplifier package. Input offset and bias current can affect buffer accuracy, particularly with high-impedance sources, so those characteristics should be checked against the source impedance. Output loading and capacitive drive should also remain within the device's operating conditions.
推荐
推荐产品汇总
工程参考数据: LM2904WHD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2904BA | LM2904B | LM2904QD | LM2904QDR |
|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Internal Frequency Compensation | Yes | Yes | Yes | Yes | Yes |
关键差异点
- Two independent amplifiers in one standard package (对比 LM324ANSR)
- Single positive-supply operation (对比 LM2902MTX)
- Compact 8-pin SOIC implementation (对比 LM2902VDG)
设计说明
Place the supply bypass capacitor adjacent to the LM2904WHD power and ground pins, with a short, low-impedance return to the ground plane. Keep each amplifier's inverting-input and feedback components close to the relevant pins to minimize parasitic feedback and oscillation risk. Route sensitive sensor inputs away from switching nodes, inductors, and high-current return paths. Assign the remaining five connections from the manufacturer pin-description table rather than from a generic dual-op-amp footprint.
Use the LM2904WHD's two independent channels as separate analog paths and avoid sharing sensitive return currents with output or digital switching currents. For high-impedance sources, verify input bias-current effects and consider a nearby bias-return resistor where appropriate. Check the selected frequency-compensated topology for stable closed-loop gain, especially with cable capacitance, large loads, or high closed-loop gain, and use the manufacturer stability guidance when adding isolation resistance.
Do not assume that a single-positive-supply amplifier can process an input or generate an output across the complete supply range. Confirm the input common-mode window and output-swing limits for the actual supply voltage and load. In battery-powered circuits, evaluate the full battery range rather than only its nominal voltage. Also verify that the selected ordering suffix maintains the required package, temperature grade, qualification, and production-packing format before approving a substitute.
合规信息
The family is described for automotive and industrial control applications, but exact compliance and qualification claims must be confirmed for the selected orderable grade. No component-level certification status was confirmed in the cited records.