LM393LVDR - Dual 1.65-5.5V Open-Drain Comparator | TI
料号: LM393LVDR ✓ 量产中LM393LVDR 概述
A comparator is a signal-conditioning semiconductor that compares two input voltages and produces a logic-level output indicating which input is higher. In the broader device hierarchy, a comparator belongs to analog and mixed-signal integrated circuits, where it supports the LDO, voltage regulator, power management IC, and embedded-control ecosystems. An open-drain comparator requires an external pull-up resistor because its output can actively pull the output node low while otherwise leaving it high-impedance.
The LM393LV family operates from 1.65 V to 5.5 V and provides two independent channels in one package. Its open-drain outputs can be pulled up to a suitable logic voltage, allowing multiple devices to share a wired bus when their output stages are not active simultaneously. The manufacturer specifies a maximum input offset voltage of 3000 uV, a maximum supply current of 0.1 mA, and a response time of 600 ns. Its operating temperature range is -40°C to +125°C.
The two comparison channels operate independently, so each channel can use separate inverting and non-inverting inputs while sharing the supply pins. Rail-to-rail input behavior makes the device useful near the lower and upper limits of its 1.65 V to 5.5 V supply range. The 600 ns response time supports general-purpose digital interfacing, while the open-drain architecture adds design flexibility through user-selected pull-up resistors and logic levels.
Typical uses include low-voltage sensor threshold detection, battery-voltage monitoring, overvoltage and undervoltage indication, signal conditioning, and digital control systems. Two comparator channels can monitor independent thresholds in one compact package, reducing board area when the application does not require rail-to-rail push-pull outputs or a specific fixed output reference.
Design the external pull-up resistor for the required sink current, output rise time, and total bus capacitance. Confirm that the pull-up voltage remains within the connected logic system’s allowed range, and account for the open-drain high-state rise time rather than assuming a CMOS push-pull output edge. Keep sensitive comparison inputs away from switching nodes and high-current return paths.
This page combines manufacturer specifications, package and pin information, drop-in replacement guidance, and practical design considerations. It also organizes the LM393LVDR for engineers evaluating low-voltage comparator selection, PCB layout, signal threshold design, and supply compatibility.
直接替换替代料: LM393LVDR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM393LVDR (相同外形与封装尺寸) ——差异在于 Package, Comparator Type, Operating Temperature Range, Response Time, Output Type.
LM393DR
✅ 直接替换✓ 有现货
$0.11 / 个
查看数据手册 →LMV393DR
✅ 直接替换📋 参考替代料(不在目录中)
LM393LVDR 最大额定值与电气特性
| Comparator Type | Dual general-purpose voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 1.65 V to 5.5 V |
| Input Common-Mode Range | Rail-to-rail |
| 输出类型 | Open drain |
| Maximum Input Offset Voltage | 3000 uV |
| Maximum Supply Current | 0.1 mA |
| Response Time | 600 ns |
| 工作温度范围 | -40°C to +125°C |
| 封装 | 8-pin SOIC (D) |
| 引脚数量 | 8 pins |
| 安装类型 | Surface mount |
| Input Pin Count | 4 inputs across 2 channels |
| Output Pin Count | 2 open-drain outputs |
| Output Pull-Up Requirement | External pull-up resistor required |
LM393LVDR 引脚配置
| 引脚 1 | OUT1 — Open-drain output for comparator channel 1 |
| 引脚 2 | IN1- — Inverting input for comparator channel 1 |
| 引脚 3 | IN1+ — Non-inverting input for comparator channel 1 |
| 引脚 4 | GND — Ground connection |
| 引脚 5 | IN2+ — Non-inverting input for comparator channel 2 |
| 引脚 6 | IN2- — Inverting input for comparator channel 2 |
| 引脚 7 | OUT2 — Open-drain output for comparator channel 2 |
| 引脚 8 | VCC — Positive supply connection |
典型应用
LM393LVDR 适用于 6 应用s: Low-Voltage Sensor Threshold Detection, Battery Voltage Monitoring, Power Rail Overvoltage Detection, Digital Logic Level Interface, LED Status and Threshold Indication, IoT Sensor and Limit Detection.
Low-Voltage Sensor Threshold Detection
The LM393LVDR fits sensor interfaces whose signal must be compared against a low-voltage reference. Its 1.65 V to 5.5 V supply range supports 1.8 V, 2.5 V, 3.3 V, and 5 V systems, while the two independent channels can monitor two sensor thresholds. Connect each non-inverting input to a reference and each inverting input to the sensed signal, then reverse the inputs when a different output polarity is required. The 3000 uV maximum offset specification is important when the sensing gap is small. Because the output is open drain, add a pull-up resistor to the interface logic voltage and include its capacitance when validating output rise time.
推荐
Battery Voltage Monitoring
The LM393LVDR is appropriate for low-voltage battery systems where a rail must be flagged before it falls outside the usable operating range. A resistor divider can scale the battery voltage to the comparator input, while the second channel can monitor a second rail or an overvoltage condition. Operation down to 1.65 V supports low-energy sensing platforms, and the 0.1 mA maximum supply current helps preserve battery capacity. Keep the divider resistance high enough to limit divider current and low enough to avoid excessive leakage effects. Use a pull-up to the monitored system’s logic rail, and account for input offset when choosing a threshold with narrow safety margins.
推荐
Power Rail Overvoltage Detection
The LM393LVDR can implement a compact overvoltage detector for a regulated 1.8 V, 2.5 V, 3.3 V, or 5 V rail. A precision divider reduces the rail voltage to the comparison input, while the comparator identifies whether the rail has crossed the selected limit. The open-drain output permits a wired fault signal with a pull-up resistor, allowing the output polarity to remain independent of the internal output driver. With two channels, the design can monitor overvoltage and undervoltage conditions without using two packages. Validate the divider tolerance, the comparator’s 3000 uV maximum offset, and the 600 ns response time before setting protection thresholds that require rapid fault signaling.
推荐
Digital Logic Level Interface
The LM393LVDR can interface a low-voltage analog signal to a digital control system because its open-drain output can be pulled up to the receiving logic voltage. This is useful when the comparator must detect a threshold without forcing a dedicated push-pull output stage. The 1.65 V to 5.5 V operating range supports both low-voltage sensors and common 3.3 V or 5 V logic domains. Select the pull-up value from the required sink current, bus capacitance, and acceptable rise time rather than using an arbitrary resistor. When multiple open-drain outputs share a node, ensure that no two devices pull the bus low simultaneously, since wired-AND behavior is intentional but may not suit every system architecture.
推荐
LED Status and Threshold Indication
The LM393LVDR can drive an LED or digital status indicator after comparing a measured voltage against a reference. The open-drain stage can sink LED current when the threshold is exceeded, while a series resistor limits current to the intended operating range. Its low-voltage operation supports compact battery-powered indicators, and the 600 ns response time provides prompt visual state changes. The external pull-up establishes the digital high level separately from the LED load. Confirm that the pull-up and LED paths do not create an unintended current path when the output releases the bus, and use transistor buffering if the indicator requires more current than the comparator output can safely sink.
推荐
IoT Sensor and Limit Detection
The LM393LVDR is useful in IoT sensor nodes that must locally detect a limit without waking a microcontroller for every threshold event. Its 1.65 V minimum supply supports low-energy rails, while two channels can handle independent limit conditions. The open-drain output can be connected to a microcontroller interrupt, power-gate signal, or shared pull-up node, reducing the number of I/O pins required. The 0.1 mA maximum supply current and 3000 uV maximum offset are particularly useful in low-power sensing designs, provided the signal margin exceeds the offset error. Use rail-to-rail inputs within the specified operating limits and keep comparator traces away from wireless-module switching and fast digital return paths to reduce false threshold events.
推荐
推荐产品汇总
工程参考数据: LM393LVDR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM393DR | LMV393DR |
|---|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Brand | Texas Instruments | Texas Instruments | STMicroelectronics |
| Comparator Channels | 2 | 2 | 2 |
| Supply Voltage Range | 1.65 V to 5.5 V | 2 V to 36 V | 2.7 V to 16 V |
| Output Type | Open drain | Open collector/open drain | Open drain |
关键差异点
- Lower minimum operating voltage (对比 LMV393DR)
- Low-voltage performance specialization (对比 LM393DR)
- Two independent channels in one package (对比 LMV393DR)
设计说明
Do not treat the open-drain output as a push-pull CMOS output. Each output requires a pull-up resistor to establish a valid high level. Select that resistor using the receiving logic voltage, required sink current, total bus capacitance, and acceptable rise time. If multiple outputs share one node, ensure the system can tolerate wired-AND behavior and that only one output attempts to pull the node low at a time.
Keep the supply within the specified 1.65 V to 5.5 V range and use the manufacturer’s absolute-maximum ratings as hard limits. Although the comparator consumes no more than 0.1 mA under the stated conditions, output sink current and pull-up resistor current contribute to the total system load. A low pull-up resistance reduces rise time but increases continuous current when an output is low, so calculate both states before finalizing the value.
Route the two high-impedance comparison inputs away from switching nodes, inductor fields, and fast digital return currents. A small input-signal margin may be affected by the 3000 uV maximum input offset and by noise coupled onto the reference or sensor trace. If the threshold is precise, use a low-noise reference, short input traces, and a stable ground reference. Avoid adding long parallel runs beneath the inputs unless the PCB stack-up provides adequate isolation.
合规信息
The manufacturer product information confirms the electrical and package specifications, but explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statements were not identified.