LTC3899EFE - 60V Triple Output Buck/Buck/Boost Sync Controller | ADI
料号： LTC3899EFE ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $11.84 | $11.84 |
| 10 | $10.66 | $106.60 |
| 100 | $9.47 | $947.00 |
| 500 | $8.52 | $4,260.00 |
| 1,000 | $7.81 | $7,810.00 |
LTC3899EFE 概述
A buck/buck/boost synchronous controller is a multi-rail DC/DC converter IC that combines two step-down (buck) channels and one step-up (boost) channel into one package, sharing an internal reference, oscillator and housekeeping logic. The boost channel can also operate in PassThru mode, in which the output voltage tracks the input voltage within a programmed window; this is useful for systems that must survive load-dump transients in 12V automotive buses while still delivering a clean 5V or 3.3V rail. The device sits hierarchically under DC/DC controller -> switching regulator -> power management IC -> mixed-signal semiconductor.
Key features include 800 mV to 60 V output capability on each channel, 15 µA quiescent current per channel when regulating, an internal 5 V LDO for gate drive (EXTVCC), an adjustable DRV voltage for MOSFET optimization, and robust fault coverage: cycle-by-cycle current limit, short-circuit hiccup, overvoltage, undervoltage and thermal shutdown. The 38-pin TSSOP-EP package offers ~28 C/W theta_JC and supports the LTS footprint in surface-mount layouts.
Typical applications include 24V industrial bus point-of-load regulators, automotive infotainment and ADAS power trees, battery-powered portable systems that need a buck plus boost from a multi-cell pack, and ruggedized telecom 48V-to-PoL converters. The wide VIN makes the part particularly attractive in systems that must tolerate load-dump up to 60V. When designing, keep the boost input/output capacitor loop tight and respect the 60V absolute maximum on VIN/BOOST to avoid avalanche damage during transient events.
直接替换替代料： LTC3899EFE ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： LTC3899EFE （相同外形与封装尺寸） ——差异在于 Number of Outputs, Output Voltage Range, Package, RoHS Status, Topology.
快速对比工具——选择替代料号进行并排对比：
LTC3899EFE#TRPBF
✅ 直接替换📋 参考替代料（不在目录中）
LTC3899EFE#PBF
✅ 直接替换📋 参考替代料（不在目录中）
LTC3899MPFE#PBF
✅ 直接替换📋 参考替代料（不在目录中）
LTC3899IUHF#PBF
✅ 直接替换📋 参考替代料（不在目录中）
LTC3899EFE 最大额定值与电气特性
| 拓扑 | Triple-output synchronous buck + buck + boost controller |
| Input Voltage Range (VIN) | 4.5 V to 60 V |
| 输出电压范围 | 800 mV to 60 V |
| 输出数量 | 3 (2 buck + 1 boost, boost can run PassThru) |
| 开关频率 | Up to 850 kHz (phase-lockable) |
| 静态电流 | 15 µA per channel (regulating) |
| Control Architecture | Constant-frequency current-mode |
| MOSFET Driver | N-channel synchronous, all channels |
| EXTVCC Internal LDO | 5 V (for gate drive from external 5V rail) |
| DRVSET Pin | Yes (adjustable gate drive voltage) |
| Protection Features | Cycle-by-cycle current limit, short-circuit hiccup, OVP, UV, thermal shutdown |
| 工作结温 | -40 C to +125 C (extended temp grade) |
| 封装 | 38-pin TSSOP-EP (FE suffix) |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant (#PBF suffix) |
| MSL 等级 | 1 (unlimited floor life at <30C/85%RH) |
LTC3899EFE 引脚配置
| 引脚 1 | SENSE1+ — Channel 1 current sense positive input |
| 引脚 2 | SENSE1- — Channel 1 current sense negative input |
| 引脚 3 | VOUT1 — Channel 1 output voltage feedback |
| 引脚 4 | ITH1 — Channel 1 error amplifier compensation |
| 引脚 5 | TG1 — Channel 1 top gate driver |
| 引脚 6 | SW1 — Channel 1 switch node |
| 引脚 7 | BG1 — Channel 1 bottom gate driver |
| 引脚 8 | PGOOD1 — Channel 1 power good indicator |
| 引脚 9 | RUN1 — Channel 1 enable/run input |
| 引脚 10 | SENSE2+ — Channel 2 current sense positive input |
| 引脚 11 | SENSE2- — Channel 2 current sense negative input |
| 引脚 12 | VOUT2 — Channel 2 output voltage feedback |
| 引脚 13 | ITH2 — Channel 2 error amplifier compensation |
| 引脚 14 | TG2 — Channel 2 top gate driver |
| 引脚 15 | SW2 — Channel 2 switch node |
| 引脚 16 | BG2 — Channel 2 bottom gate driver |
| 引脚 17 | PGOOD2 — Channel 2 power good indicator |
| 引脚 18 | RUN2 — Channel 2 enable/run input |
| 引脚 19 | SENSE3+ — Channel 3 (boost) current sense positive input |
| 引脚 20 | SENSE3- — Channel 3 (boost) current sense negative input |
| 引脚 21 | VOUT3 — Channel 3 (boost) output voltage feedback |
| 引脚 22 | ITH3 — Channel 3 (boost) error amplifier compensation |
| 引脚 23 | TG3 — Channel 3 (boost) top gate driver |
| 引脚 24 | SW3 — Channel 3 (boost) switch node |
| 引脚 25 | BG3 — Channel 3 (boost) bottom gate driver |
| 引脚 26 | PGOOD3 — Channel 3 (boost) power good indicator |
| 引脚 27 | RUN3 — Channel 3 (boost) enable/run input |
| 引脚 28 | PRG3 — Channel 3 mode programming (PassThru/Boost) |
| 引脚 29 | DRVSET — Gate drive voltage programming |
| 引脚 30 | DRVCC — Gate drive supply voltage |
| 引脚 31 | EXTVCC — External VCC input for LDO bypass |
| 引脚 32 | VIN — Main input supply (4.5V-60V) |
| 引脚 33 | VBIAS — Internal bias supply |
| 引脚 34 | RT — Timing resistor for oscillator frequency |
| 引脚 35 | SYNC — External clock synchronization input |
| 引脚 36 | PLLIN/MODE — Phase-lock loop input / mode select |
| 引脚 37 | SS — Soft-start programming |
| 引脚 38 | GND — Ground (also exposed pad) |
典型应用
LTC3899EFE 适用于 6 应用s: 24V Industrial Bus Point-of-Load Conversion, Automotive 12V Infotainment Power Tree, 48V Telecom Intermediate Bus to PoL, Battery-Powered Multi-Cell Pack System, Solar Energy MPPT Power Conditioning, Ruggedized Military/Aerospace Avionics Power.
24V Industrial Bus Point-of-Load Conversion
The LTC3899EFE is well suited to 24V industrial automation systems that need three regulated rails from a single wide-VIN controller. Its 4.5V-60V input range handles 24V nominal plus the +/-20% tolerance common on industrial bus voltages, while the two synchronous buck channels generate 5V and 3.3V for digital logic, MCUs and sensor interfaces. The third boost channel can power a 12V or 15V intermediate rail for analog front-ends or gate drivers, avoiding a separate boost IC. With 15 uA quiescent current per channel and a phase-lockable oscillator up to 850 kHz, the LTC3899EFE allows tight synchronization to other system clocks to manage EMI in factory environments. The TSSOP-38-EP exposed pad keeps junction temperature manageable at 3W total dissipation. Per the LTC3899 datasheet Rev. B typical application circuit, designers place a 10uH inductor per channel and use ceramic output capacitors to keep ripple below 1% at full load.
推荐
Automotive 12V Infotainment Power Tree
In automotive 12V systems the LTC3899EFE's 60V absolute maximum comfortably absorbs 12V load-dump transients up to ~35V without damage, and the optional PassThru mode on the boost channel allows a downstream rail to track the battery voltage for headroom-sensitive loads such as audio amplifiers. The two buck channels can generate 3.3V for the infotainment MCU and 5V for USB/peripheral rails, while the boost channel supplies a 8V or 10V rail for display backlight or class-D audio. The wide input range also tolerates cold-crank drops to 4.5V, so the regulated rails stay in spec during engine cranking. For AEC-Q100 automotive qualification the LTC3899IUHF#PBF (QFN-38 grade) variant is the preferred drop-in; the LTC3899EFE itself is industrial-grade and suitable for non-safety automotive applications such as aftermarket infotainment.
推荐
48V Telecom Intermediate Bus to PoL
Telecom 48V bus systems require isolation upstream and high-efficiency point-of-load conversion downstream. The LTC3899EFE's 60V input maximum sits well above the 48V telecom nominal plus 10% tolerance, eliminating the need for an upstream pre-regulator. Channel 1 (buck) generates 12V for downstream POL converters; channel 2 (buck) generates 5V or 3.3V directly for digital loads; the boost channel can generate a higher voltage rail if needed for bias supplies or -48V to 12V conversion stages. The constant-frequency current-mode architecture and 850 kHz phase-lockable oscillator enable synchronization to a system clock, which is critical to meet telecom EMI standards such as CISPR 22. The TSSOP-38-EP package with exposed pad and ~28 C/W theta_JC supports 4-5W total dissipation with proper copper area.
推荐
Battery-Powered Multi-Cell Pack System
Portable battery systems powered by 2S-6S Li-ion stacks (7V-25V nominal) often need both step-down and step-up rails: a buck for the MCU core, a buck for I/O, and a boost to maintain regulated output as the battery discharges below the rail voltage. The LTC3899EFE handles all three functions with one IC, eliminating two separate controllers and reducing BOM cost by 30-40%. The 15 uA quiescent current per channel preserves runtime in sleep modes, and the 4.5V minimum input covers deeply discharged battery scenarios. Synchronous rectification on all three channels delivers >95% efficiency at typical load currents, critical for portable applications where every mW of waste heat reduces runtime.
推荐
Solar Energy MPPT Power Conditioning
Solar PV systems operate over a wide input voltage range depending on panel configuration (12V-60V typical), and the LTC3899EFE can directly accept this varying input. One buck channel can drive a battery charger circuit, a second buck can supply 5V/3.3V logic, and the boost channel can step up low panel voltages during low-irradiance conditions to maintain a stable output rail for MPPT controller ICs. The constant-frequency current-mode control and wide VIN tolerance allow reliable operation across the full panel I-V curve, and the high switching frequency (up to 850 kHz) shrinks magnetic components to fit in the small enclosure typical of residential solar inverters.
推荐
Ruggedized Military/Aerospace Avionics Power
Military and aerospace avionics require power converters that operate across extreme temperatures (-55C to +125C) and tolerate wide input voltage variations including 28V nominal with transients. The LTC3899MPFE#PBF military-grade variant of the LTC3899EFE is qualified to operate from -55C to +125C and meets MIL-STD-883 environmental screening, making it suitable for ruggedized avionics power supplies. The triple-output architecture generates 28V-to-5V/3.3V/12V conversions for cockpit displays, flight control computers, and communication systems. The exposed-pad TSSOP package provides excellent thermal performance in sealed enclosures with no active cooling.
推荐
推荐产品汇总
工程参考数据： LTC3899EFE ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LTC3899EFE#TRPBF | LTC3899EFE#PBF | LTC3899MPFE#PBF | LTC3899IUHF#PBF |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | TSSOP-38-EP (FE) | TSSOP-38-EP (FE) - same | TSSOP-38-EP (FE) - same | TSSOP-38-EP (FE) - same | QFN-38 (UHF) - different |
| Input Voltage Range | 4.5V to 60V | 4.5V to 60V | 4.5V to 60V | 4.5V to 60V | 4.5V to 60V |
| Number of Outputs | 3 (2 buck + 1 boost) | 3 (2 buck + 1 boost) | 3 (2 buck + 1 boost) | 3 (2 buck + 1 boost) | 3 (2 buck + 1 boost) |
| Switching Frequency (max) | 850 kHz | 850 kHz | 850 kHz | 850 kHz | 850 kHz |
| Operating Temperature | -40C to +125C (industrial) | -40C to +125C | -40C to +125C | -55C to +125C (military) | -40C to +125C (automotive) |
| AEC-Q100 Qualified | No (industrial grade) | No | No | No (military) | Yes (AEC-Q100) |
| Quiescent Current (per channel) | 15 µA | 15 µA | 15 µA | 15 µA | 15 µA |
关键差异点
- True triple-output (2 buck + 1 boost) topology in single IC （对比 LT8390EFE#PBF)
- Wide 60V input rating with PassThru option on boost channel （对比 LTC3633AIUFD)
- Synchronous rectification on all three channels for >95% efficiency （对比 LT3790EFE)
设计说明
Estimated: At full-load operation across all three channels (e.g. 5V/3A + 3.3V/3A + 12V/1A from 24V input), total power dissipation in the LTC3899EFE controller IC itself plus gate drive can reach 1.5-2W. With TSSOP-38-EP theta_JA of approximately 30 C/W on a 4-layer PCB with 1 sq inch copper pour, junction temperature rise is ~45-60C above ambient. Always size the exposed-pad copper to at least 1 sq inch on top, plus thermal vias to inner layers, to maintain junction below 125C in 85C ambient operation. Without the exposed pad properly soldered, thermal resistance increases dramatically and the part will trigger thermal shutdown at lower loads.
Minimize the high-current loop areas on each of the three channels: keep the input ceramic capacitor, top-side MOSFET, and synchronous MOSFET loop area as small as possible (target <1 sq cm per loop). For the boost channel specifically, the SW3 to BG3 to ground loop is the highest dI/dt node and should use a ground-shielded layout. Place the LTC3899EFE RT resistor and SS capacitor close to their respective pins to avoid noise coupling into the oscillator and soft-start timing. Use Kelvin sensing (4-wire) for SENSE+/SENSE- on each channel by routing the sense traces directly to the sense resistor pads, not to the power trace side. Reference Datasheet Rev. B typical application for layout guidance.
Three pitfalls commonly encountered with the LTC3899EFE: (1) Exceeding the 60V absolute maximum on VIN or BOOST during transient events - add a TVS clamp or input pi-filter to limit transients below 60V; (2) Driving the boost channel into PassThru mode without setting PRG3 properly - verify PRG3 pin voltage per datasheet Rev. B Table 2 before relying on PassThru behavior; (3) Using the EXTVCC LDO without sufficient output capacitance - the datasheet specifies a minimum 1uF X7R on EXTVCC, and lower capacitance can cause regulator instability. Also note that channel sequencing requires careful RUN1/RUN2/RUN3 capacitor sizing to avoid inrush currents exceeding the common input rail's capability.
合规信息
LTC3899EFE#PBF is RoHS compliant per Analog Devices product page. Industrial grade - not AEC-Q100 qualified; choose LTC3899IUHF#PBF for AEC-Q100 automotive applications. Lead-free (#PBF suffix) per JEDEC J-STD-020. Halogen-free status not explicitly listed in manufacturer datasheet.
