MAX202CUE+T - Dual RS-232 Transceiver | Analog Devices
料号: MAX202CUE+T ✓ 量产中MAX202CUE+T 概述
An RS-232 transceiver is an interface IC that converts logic-level signals into differential voltage levels and converts incoming RS-232 signals back into logic-compatible levels. Within the interface hierarchy, the MAX202 belongs to the RS-232 transceiver family, a type of line-driver and receiver interface used between data-processing equipment and serial equipment. Its purpose is to bridge incompatible voltage domains while providing the electrical characteristics required by the EIA/TIA-232E interface standard.
Key features include two drivers, two receivers, full-duplex operation, a 120 kbps data rate, and a 4.5 V to 5.5 V supply range. The receiver hysteresis of 500 mV helps distinguish valid logic states in the presence of noise. Because the MAX202 uses externally mounted charge-pump capacitors, PCB layout can provide flexibility in capacitor selection and placement, although trace length and ground return paths still require careful attention.
The device implements separate transmit and receive paths for two serial channels. Each driver translates TTL or CMOS-level inputs into RS-232 levels, while each receiver converts RS-232 inputs into CMOS-compatible outputs. This arrangement supports bidirectional data exchange without requiring separate RS-232 converter boards. The single 5 V supply also simplifies integration with microcontrollers and other digital logic that operate from the same rail.
Typical uses include industrial serial controllers, test and measurement equipment, point-of-sale terminals, security systems, and embedded diagnostic interfaces. The MAX202CUE+T is especially appropriate when a compact TSSOP footprint is preferred over a larger SOIC package. It can connect a short RS-232 cable between a host and peripheral while preserving the voltage separation required by legacy serial equipment.
A critical implementation detail is charge-pump capacitor placement. Keep the 0.1 uF capacitors close to their associated IC pins, use the package pin-description table when assigning tracks, and maintain a low-impedance ground connection. Capacitor selection should follow the manufacturer’s recommended dielectric and voltage requirements because incorrect capacitor behavior can impair startup or charge-pump operation.
This product page combines manufacturer specifications, packaging details, functional comparisons, and practical PCB guidance for engineers evaluating the MAX202CUE+T. It also identifies the small number of verified pin-compatible options so that replacement decisions can be based on package, function, and electrical proximity rather than part-number similarity alone.
直接替换替代料: MAX202CUE+T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX202CUE+T (相同外形与封装尺寸) ——差异在于 Maximum Data Rate, Product Type, Mounting Type, Package, ESD Protection.
MAX202CPWR
✅ 直接替换✓ 有现货
$0.9023 / 个
查看数据手册 →MAX202CUE+
✅ 直接替换联系询价
查看数据手册 →MAX202CUE+T 规格参数
| Product Type | Dual RS-232 line-driver and receiver transceiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Duplex Mode | Full duplex |
| Maximum Data Rate | 120 kbps |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Receiver Hysteresis | 500 mV |
| External Charge-Pump Capacitor Value | 0.1 uF |
| 封装 | 16-pin TSSOP |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Commercial |
| 安装类型 | Surface mount |
| Interface Standard | EIA/TIA-232E |
| Driver Output Levels | ±5 V under EIA/TIA-232E loading |
| ESD Protection | ±15 kV on serial-port connection pins |
MAX202CUE+T rectangular 引脚配置指南
MAX202CUE+T(rectangular 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX202CUE+T.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX202CUE+T 适用于 6 应用s: Industrial Serial Controller Interface, Test and Measurement Equipment, Point-of-Sale Terminal Connectivity, Security and Access-Control Equipment, Embedded Diagnostic and Service Port, Data Acquisition Equipment.
Industrial Serial Controller Interface
The MAX202CUE+T fits industrial control equipment that must communicate with a legacy RS-232 service port or peripheral. Its two drivers and two receivers support two full-duplex channels at up to 120 kbps, while the 4.5 V to 5.5 V supply range permits operation from a regulated 5 V rail. The 500 mV receiver hysteresis improves noise immunity around the input threshold. Place the external 0.1 uF charge-pump capacitors close to the device and route the interface ground directly to the board ground plane to reduce susceptibility to ground bounce and cable-borne noise.
推荐
Test and Measurement Equipment
The MAX202CUE+T is suitable for test instruments, laboratory controllers, and service interfaces that exchange commands with RS-232 equipment. The dual 2/2 full-duplex configuration allows a controller to maintain two communication paths without adding separate interface ICs, and the 120 kbps rate is appropriate for command-and-response protocols. The single 5 V supply simplifies integration with digital control logic. Keep signal traces short, use a continuous ground reference, and verify the external charge-pump capacitor values against the manufacturer recommendations before validation.
推荐
Point-of-Sale Terminal Connectivity
Retail peripherals such as scales, printers, and customer displays commonly use RS-232 links. The MAX202CUE+T provides two drivers, two receivers, full-duplex communication, and a 120 kbps maximum data rate, which suits short command-based transactions and configuration exchanges. Its 16-pin TSSOP package conserves board area compared with larger through-hole or SOIC implementations. Use short, properly referenced cable connections and confirm that the host logic levels match the CMOS-compatible receiver outputs. External surge protection may be required when the cable leaves a controlled enclosure.
推荐
Security and Access-Control Equipment
The MAX202CUE+T can provide the RS-232 interface used by access-control readers, alarm panels, and configuration adapters. Its full-duplex 2/2 arrangement allows command transmission and status reception on two channels, while the 120 kbps rate is more than sufficient for short administrative packets. Receiver hysteresis of 500 mV helps reject small disturbances that could otherwise cause false transitions. For installations with long cables or poor grounds, include suitable transient protection and route the cable shield according to the complete equipment grounding strategy.
推荐
Embedded Diagnostic and Service Port
The MAX202CUE+T is useful in embedded instruments that expose a service or diagnostic connector through an RS-232 interface. Two receive channels can support status reporting or an auxiliary link, while two driver channels support command transmission and handshaking. Operation from 4.5 V to 5.5 V keeps the interface compatible with common 5 V embedded systems, and the 120 kbps rate matches many bootloader and configuration protocols. Maintain consistent ground references between boards and use the manufacturer pin table to assign the charge-pump capacitor network without altering the footprint.
推荐
Data Acquisition Equipment
The MAX202CUE+T can connect laboratory data-acquisition equipment to an RS-232 controller when command traffic and remote signaling must coexist. Its 2/2 full-duplex arrangement reduces the number of separate transceivers needed for bidirectional communications, and the 120 kbps data rate accommodates typical configuration and status traffic. The receiver hysteresis of 500 mV improves noise tolerance, while the 16-pin TSSOP package supports compact controller boards. For sensitive measurements, keep the RS-232 circuitry away from analog inputs and use a dedicated ground strategy to prevent interface current from disturbing the measurement system.
推荐
推荐产品汇总
工程参考数据: MAX202CUE+T ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX202CPWR | MAX202CUE |
|---|---|---|---|
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Brand | Analog Devices | Texas Instruments | Analog Devices |
| Transceiver Configuration | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers |
| Duplex Mode | Full duplex | Full duplex | Full duplex |
| Maximum Data Rate | 120 kbps | 120 kbps | 120 kbps |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Receiver Hysteresis | 500 mV | 500 mV | 500 mV |
| External Charge-Pump Capacitor | 0.1 uF | 0.1 uF | 0.1 uF |
| Interface Standard | EIA/TIA-232E | TIA/EIA-232-F | EIA/TIA-232E |
关键差异点
- Compact dual-channel RS-232 implementation (对比 MAX202CPWR)
- Direct ordering alignment with the target MAX202 family (对比 MAX202CUE)
- Noise-tolerant receiver threshold (对比 MAX202CUE)
设计说明
Place the external 0.1 uF charge-pump capacitors directly beside the associated MAX202CUE+T pins and use the shortest practical traces. Avoid routing the capacitor connections through unrelated signal layers. Confirm the exact terminal positions using the manufacturer pin-description table because an incorrect footprint can prevent the charge-pump network from operating correctly even when the IC itself is properly placed.
Connect the device ground to a low-impedance ground plane and route RS-232 cable returns as a controlled reference path. Keep the transceiver away from switching nodes, high-current return paths, and sensitive analog inputs. If the cable leaves the equipment, provide a defined chassis or signal-ground strategy and evaluate whether additional surge or transient protection is required for the installation environment.
Do not assume that two MAX202-family ordering codes are interchangeable without checking the pinout, temperature grade, reel configuration, and lifecycle requirements. A suffix can identify commercial or packaging differences even when the core RS-232 function is the same. Verify the exact marking and ordering information before substituting a part, especially for designs moving into automated production or long-term maintenance.
Treat the RS-232 cable interface as a separate, potentially noisy signal environment even though the logic side operates at 5 V. Use a proper ground reference, minimize stub lengths, and test the completed board with the intended cable and peripheral. Receiver hysteresis of 500 mV improves transition noise immunity, but it does not compensate for poor grounding or unprotected long cable runs.
合规信息
The MAX202 family is associated with EIA/TIA-232E interface requirements. Specific RoHS, REACH, automotive, lead-free, halogen-free, and conflict-minerals status was not established for the exact MAX202CUE+T ordering configuration.