MAX232CWE-TG074 - 120kbps RS-232 Transceiver | Analog Devices
料号: MAX232CWE-TG074 ✓ 量产中MAX232CWE-TG074 概述
A MAX232 is a bipolar RS-232 interface IC that converts TTL/CMOS-compatible logic signals into RS-232 levels and converts incoming RS-232 signals back into logic levels. Within the interface hierarchy, it belongs to the line-driver and receiver category, interface IC family, and broader semiconductor product group. Two driver channels and two receiver channels allow one device to support a full-duplex serial link.
The MAX232CWE-TG074 supports operation at up to 120kbps, making it suitable for common serial-console, industrial-control, point-of-sale, and embedded equipment links. Its integrated level translation reduces the need for external RS-232 driver and receiver components. The 16-SOIC package supports conventional surface-mount assembly and is suitable for compact industrial and commercial equipment designs.
The MAX220 through MAX249 family is designed around EIA/TIA-232E and V.28/V.24 interface requirements, particularly where positive and negative supply voltages of approximately ±12V are not available. The CWE-TG074 ordering form identifies this part as a 16-SOIC RS-232 driver/receiver interface with two drivers and two receivers. Its interface architecture supports simultaneous transmit and receive paths when the host and peripheral provide complementary data and control signals.
Typical applications include configuration-port and console interfaces in embedded systems, communication links between microcontrollers and industrial peripherals, RS-232 test equipment, and legacy peripheral connections requiring bidirectional data transfer. Designers should pay particular attention to cable length, signal integrity, grounding, and the distinction between logic-level and RS-232 voltage domains.
For a new layout, place the MAX232CWE-TG074 close to the connector and preserve short, direct routes for the driver outputs and receiver inputs. Check the device's receive thresholds and the logic-level supply requirements of the connected controller. Add the charge-pump capacitors recommended by the manufacturer at the designated pins and avoid long stubs that could increase ringing or susceptibility to ESD events.
This product page combines the available manufacturer-family information, package identification, interface characteristics, application guidance, and drop-in replacement options in a format designed for engineering selection. For complete channel assignments, absolute maximum ratings, electrical characteristics, and layout guidance, use the official MAX232CWE datasheet and the exact pin-description table before releasing a PCB or production design.
直接替换替代料: MAX232CWE-TG074 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX232CWE-TG074 (相同外形与封装尺寸) ——差异在于 Interface Standard, Package, Product Type.
MAX232CWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232CWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232AWE+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX232CSE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232EWE+
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232CWE-TG074 规格参数
| Product Type | RS-232 driver/receiver transceiver |
| Driver Channels | 2 |
| Receiver Channels | 2 |
| Maximum Data Rate | 120kbps |
| Interface Standard | EIA/TIA-232E and V.28/V.24 |
| 封装 | 16-SOIC |
| 安装类型 | Surface mount |
| 引脚数 | 16 pins |
MAX232CWE-TG074 16-soic 引脚配置指南
MAX232CWE-TG074(16-soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232CWE-TG074.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232CWE-TG074 适用于 6 应用s: Embedded Serial Console, Industrial Control Equipment, Point-of-Sale Terminal Interface, Instrumentation and Test Equipment, Network Equipment Management Port, Printer and Legacy Peripheral Connection.
Embedded Serial Console
The MAX232CWE-TG074 fits embedded systems that expose a debug or configuration console through an RS-232 port. Its two-driver and two-receiver arrangement supports a full-duplex link, while the 120kbps maximum data rate is appropriate for command-line traffic, boot messages, and low-volume configuration transfers. Place the interface near the serial connector, route driver and receiver traces directly to protection circuitry, and follow the manufacturer charge-pump capacitor placement recommendations. The principal design consideration is maintaining clean logic-level timing while presenting compliant bipolar voltage levels at the connector.
推荐
Industrial Control Equipment
The MAX232CWE-TG074 can connect industrial-control equipment, test fixtures, and service ports that retain RS-232 interfaces. Two drivers and two receivers provide enough channels for a typical point-to-point full-duplex arrangement, and the 120kbps class accommodates many legacy supervisory protocols. The 16-SOIC package also simplifies panel-board and controller-board layouts. For industrial cable connections, verify the required operating-temperature grade and consider external surge or ESD protection because the connector environment may be harsher than the protected logic side of the circuit.
推荐
Point-of-Sale Terminal Interface
The MAX232CWE-TG074 is suitable for point-of-sale terminals, peripherals, and service equipment using an RS-232 command channel. The two transmit and two receive channels support full-duplex communication, and 120kbps is sufficient for many transaction, status, and configuration protocols. Place the IC near the DB9 or equivalent connector to minimize trace exposure and include the required charge-pump capacitors close to their designated pins. Validate the host-side logic levels and connector wiring before production, since RS-232 is a bipolar voltage interface rather than a direct 5V UART connection.
推荐
Instrumentation and Test Equipment
The MAX232CWE-TG074 can serve as the RS-232 interface in laboratory instruments, automated test systems, and bench controls. A 120kbps channel is well suited to remote commands and measurement data exchanges that do not require continuous high-bandwidth transfers. Its dual-driver and dual-receiver arrangement allows one IC to handle both control output and status input. Keep the analog or sensitive measurement circuitry separate from connector-associated return currents, use a defined ground strategy, and verify the receiver's logic output levels against the controller used in the instrument.
推荐
Network Equipment Management Port
The MAX232CWE-TG074 is appropriate for legacy network switches, routers, and management accessories that provide a serial console through RS-232. The 120kbps rate and two-channel transceiver arrangement are sufficient for console login, configuration commands, and diagnostic output. Place the interface near the connector and route the receiver path away from switching-power and clock signals to reduce coupling. Verify the required temperature and qualification conditions against the equipment's environmental specification, and apply connector-side protection when the management port is accessible from an external cable.
推荐
Printer and Legacy Peripheral Connection
The MAX232CWE-TG074 enables a modern controller or embedded board to communicate with printers, scanners, scales, and other legacy peripherals using RS-232. The 2/2 driver-receiver arrangement supports bidirectional command and status traffic, while the 120kbps rate suits many peripheral protocols. The device converts between the controller's logic-level UART and the bipolar signal expected by the RS-232 endpoint. Check connector pin numbering, signal direction, cable length, and logic thresholds before assembly, because these details determine whether the physical connection operates correctly despite using the same transceiver package.
推荐
推荐产品汇总
工程参考数据: MAX232CWE-TG074 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232CWE | MAX232CWE+ | MAX232AWE+ | MAX232CSE+ | MAX232EWE+ |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Driver Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Receiver Channels | 2 | 2 | 2 | 2 | 2 | 2 |
关键差异点
- Established MAX232 family integration (对比 MAX232CWE)
- Existing 16-SOIC board footprint (对比 MAX232CSE+)
- Same channel count for embedded and industrial links (对比 MAX232AWE+)
- Full-duplex RS-232 channel allocation (对比 MAX232EWE+)
设计说明
Place the MAX232CWE-TG074 close to the RS-232 connector so the driver outputs and receiver inputs form short, direct routes. Position the charge-pump capacitors close to their designated IC pins and use the exact values and topology shown in the manufacturer application circuit. Keep the logic-side UART traces away from connector wiring, and provide a direct return-path strategy so receiver thresholds are not affected by large ground-potential differences.
RS-232 uses a bipolar voltage interface, so do not connect its driver outputs directly to a 5V UART. Confirm which connector pins are TX, RX, ground, and control, and cross-check the controller UART TX and RX assignments. Keep external protection components close to the connector and maintain symmetric routing where possible. Verify rise and fall times and data-rate margin against the 120kbps device limit in the manufacturer datasheet.
Do not substitute a different MAX232 order code solely from the package count. The A, C, and E family variants can share a 16-SOIC footprint while differing in temperature range, supply requirements, logic thresholds, or qualification conditions. Before reusing an existing PCB, compare the complete ordering information, electrical characteristics, exposed package dimensions, and manufacturer pinout. Also confirm that the charge-pump capacitor values used by the original design match the replacement.
合规信息
Compliance declarations were not identified in the available manufacturer-family and distributor information. Confirm the current declarations using the exact ordering code and manufacturer documentation.