MAX232EIPWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
料号: MAX232EIPWR ✓ 量产中MAX232EIPWR 概述
An RS-232 transceiver is an interface IC that bridges the voltage-domain difference between a digital controller and a physical RS-232 link. In the signal hierarchy, the MAX232EIPWR belongs to the RS-232 transceiver class, which combines line drivers, line receivers, and charge-pump voltage generation within one interface package. Unlike a TTL/CMOS serial controller, this device does not implement a communication protocol; it converts logic levels and protects the physical interface.
Key electrical features include 5V operation, dual transmit and receive channels, 250kbps maximum data rate, and approximately ±9V RS-232 output levels. According to the MAX232E product page, all RS-232 pins provide 15kV human-body-model and IEC61000-4-2 air-gap discharge protection. The line-driver pins additionally provide 8kV IEC61000-4-2 contact-discharge protection, making the interface suitable for industrial equipment, service ports, and external cables where electrostatic discharge is a practical concern.
The integrated voltage generator eliminates the need for a separate negative supply rail. Four charge-pump capacitors allow the device to translate TTL/CMOS transmit inputs into RS-232 levels from one 5V supply. Each receiver converts a TIA/EIA-232-F input into a 5V TTL/CMOS signal, allowing a microcontroller, programmable logic controller, or test system to communicate over a legacy serial port without a separate level-shifting circuit.
Typical uses include industrial control-panel service ports, configuration and debug interfaces, laboratory equipment, point-of-sale systems, and legacy peripherals that retain an RS-232 connection. The 250kbps capability supports moderate-rate command and data links, although the connected software protocol must also be configured for the selected baud rate. Because RS-232 is a point-to-point, single-ended interface, ground reference and cable routing remain important in multi-device installations.
For PCB layout, place the charge-pump capacitors and the VCC bypass capacitor close to their associated pins, and route the RS-232 driver and receiver connections directly to the connector. Keep logic-side traces away from exposed cable-facing nets, provide a stable chassis or signal-ground connection strategy, and avoid long unprotected stubs. The integrated ESD protection reduces connector-side risk but does not eliminate the need for good mechanical grounding and cable management.
This page consolidates the verified MAX232E electrical characteristics, ordering information, protection ratings, application guidance, and interface design considerations into a practical engineering reference. It also distinguishes the MAX232EIPWR from related MAX232 and MAX3232E family members so engineers can assess pin compatibility, supply voltage, data rate, and package differences before approving a substitution.
直接替换替代料: MAX232EIPWR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX232EIPWR (相同外形与封装尺寸) ——差异在于 Package, Maximum Data Rate, Product Type, Supply Voltage Range.
MAX3232EIPWG4
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX232EIPWR 规格参数
| Product Type | Dual RS-232 driver and receiver transceiver |
| Number of Channels | 2 channels |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| 电源电压 | 5 V |
| Maximum Data Rate | 250 kbps |
| RS-232 Output Level | Approximately -9 V to +9 V |
| Receiver Input Level | TIA/EIA-232-F input converted to 5 V TTL/CMOS |
| On-Chip Voltage Generator | Yes, capacitive voltage generator using four capacitors |
| ESD Protection on RS-232 Pins | 15 kV HBM and 15 kV IEC61000-4-2 air-gap discharge |
| Contact Discharge Protection | 8 kV IEC61000-4-2 on RS-232 driver pins |
| 封装 | 16-pin TSSOP |
| 安装类型 | Surface mount |
| Supply Topology | Single 5 V supply |
| Standard | TIA/EIA-232-F |
MAX232EIPWR 16-pin tssop 引脚配置指南
MAX232EIPWR(16-pin tssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232EIPWR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232EIPWR 适用于 6 应用s: Industrial Controller Service Port, Point-of-Sale Terminal Interface, Laboratory Instrument Control, Legacy Peripheral Upgrade, Programmable Logic Debug Interface, Data Acquisition and Test System.
Industrial Controller Service Port
The MAX232EIPWR fits an industrial controller that retains an RS-232 configuration or service port alongside a modern microcontroller. Its two driver and two receiver channels support bidirectional console communication, while the single 5V supply avoids a separate negative rail. The 15kV HBM and IEC61000-4-2 air-gap protection ratings improve robustness on externally accessible RS-232 pins. Place the charge-pump capacitors and supply bypass capacitor close to the device, and connect the cable shield or signal ground according to the installation’s grounding strategy.
推荐
Point-of-Sale Terminal Interface
A point-of-sale system can use the MAX232EIPWR to bridge a 5V controller to an RS-232 peripheral such as a receipt printer, customer display, or magnetic-stripe reader. Two channels allow separate transmit and receive paths without adding another transceiver. The integrated capacitive voltage generator produces the required bipolar RS-232 levels from the controller’s 5V supply. Keep the interface connector physically separated from high-current switching circuitry and verify that the peripheral’s electrical standard is TIA/EIA-232-F rather than RS-485.
推荐
Laboratory Instrument Control
The MAX232EIPWR can connect a laboratory instrument’s control board to a legacy RS-232 test fixture or service computer. Its 250kbps maximum data rate is suitable for command traffic and moderate measurement data, while the integrated voltage generator simplifies single-supply test equipment. ESD protection on the cable-facing pins helps laboratories where instruments are frequently connected and disconnected. For reliable measurements, use shielded cable, establish one reference ground, and avoid sharing noisy return paths between the interface and precision analog circuitry.
推荐
Legacy Peripheral Upgrade
The MAX232EIPWR allows a new digital controller to communicate with a legacy peripheral that exposes only an RS-232 connector. Because the receivers operate from the same 5V system used by many modern controllers, the interface can replace a more complex discrete level-shifting circuit. Verify the peripheral’s baud rate, logic polarity, handshake requirements, and connector pinout before connecting it. Software must also support the RS-232 protocol because the MAX232EIPWR performs only electrical level conversion and ESD protection.
推荐
Programmable Logic Debug Interface
The MAX232EIPWR can provide a simple two-channel console or programming interface for programmable logic or embedded-control boards. One pair of channels can carry serial commands and status information while another pair is available for auxiliary data or a second port. The 250kbps capability is substantially faster than the low-rate console links commonly used in RS-232 systems. Place the device near the connector, preserve the recommended charge-pump layout, and keep the logic-side interface away from the protected cable-side nets.
推荐
Data Acquisition and Test System
The MAX232EIPWR is useful in data-acquisition equipment that must retain an RS-232 link for calibration, logging, or external test commands. Its two full-duplex channels can operate on separate ports, and the integrated charge pump reduces external power-conversion complexity. The interface’s IEC61000-4-2 protection helps when the port is exposed to operator-accessible cables, although the overall enclosure still determines the final electrostatic-discharge environment. Use a dedicated return-ground path to keep interface transients away from measurement references.
推荐
推荐产品汇总
工程参考数据: MAX232EIPWR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3232EIPW | MAX232EIPWRR |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin TSSOP | 16-pin TSSOP | 16-pin TSSOP |
| Device Type | Dual RS-232 driver and receiver | Dual RS-232 driver and receiver | Dual RS-232 driver and receiver |
| Supply Voltage | 5 V | 5 V | 5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps |
| Number of Channels | 2 | 2 | 2 |
| RS-232 Output Swing | Approximately ±9 V | Approximately ±9 V | Approximately ±9 V |
| Voltage Generator | Internal capacitive generator using four capacitors | Internal capacitive generator | Internal capacitive generator using four capacitors |
关键差异点
- Integrated protected RS-232 interface in a single 5V part (对比 MAX3232EIPW)
- Single-supply negative-rail generation (对比 MAX232EIPWRR)
- Two-channel bidirectional connectivity (对比 MAX3232EIPW)
设计说明
Place the four charge-pump capacitors and the VCC bypass capacitor as close as practical to their specified pins. Keep the charge-pump loop compact because long traces and large loop area can increase radiated emissions. Follow the MAX232E datasheet for capacitor values and connections. Route the RS-232 connector nets directly to the transceiver, and keep those nets away from sensitive analog inputs and high-speed digital clocks.
Do not treat the RS-232 interface as a differential bus or connect it to an RS-485 receiver. MAX232EIPWR uses bipolar single-ended signaling and requires an RS-232-compatible receiver with the correct ground reference. Also verify the full device suffix before layout because package, temperature, and packing codes differ among MAX232E orderable configurations. Do not substitute a SOIC package for the specified 16-pin TSSOP without a PCB footprint change.
The on-chip capacitive voltage generator switches internally to create negative RS-232 voltage, so supply-current transitions and radiated noise deserve attention. Provide a low-impedance 5V connection, place the bypass capacitor adjacent to VCC, and avoid routing the charge-pump network beneath sensitive analog sections. At the cable interface, use a defined signal-ground or chassis-ground strategy appropriate to the equipment and keep exposed cable wiring short relative to the ESD-current path.
RS-232 is point-to-point, so each driver should connect to one receiving node and unused driver or receiver inputs should not be left as unterminated test points. Confirm the logic polarity of the connected controller, because the MAX232EIPWR provides voltage conversion rather than protocol inversion or configuration. Long cables can accumulate noise and reflections; use a quality shielded cable, maintain a continuous reference ground, and avoid daisy-chaining RS-232 ports.
合规信息
The manufacturer documentation identifies IEC61000-4-2 air-gap and contact-discharge protection ratings. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not confirmed.