MAX3243ECAI+TG1Z - 3V RS-232 Transceiver | Analog Devices
料号: MAX3243ECAI+TG1Z ✓ 量产中MAX3243ECAI+TG1Z 概述
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts incoming RS-232 signals back into logic-compatible levels. It belongs to the line-driver and line-receiver hierarchy, connecting UART, microprocessor, or industrial-control logic to a cable-based serial port. The MAX3243 family is particularly useful when a design requires more than the standard two-transmitter, two-receiver arrangement and also needs low-power standby operation.
Key features include three active drivers, five receivers, and one always-active receiver intended for external monitoring. The 3.0V to 5.5V supply range supports both 3.3V and 5V systems. Automatic shutdown and wakeup reduce power when the connected equipment is inactive, while the always-active receiver permits monitoring without keeping the main transmitter circuitry powered. The 120 kbit/s data rate covers legacy RS-232 equipment and industrial serial links.
The MAX3243 uses charge-pump circuitry to generate the bipolar voltage levels required by RS-232 while operating from a single low-voltage supply. Its enhanced ESD protection is intended for interfaces connected to external cables, where electrostatic discharge and switching transients are more likely than on internal logic nets. Because the interface is not a differential communications standard, cable length, grounding, termination, and data direction must be considered during system integration.
Typical uses include industrial control consoles, laboratory equipment, POS terminals, printers, data-acquisition systems, and service interfaces. The five-receiver arrangement can support several incoming RS-232 connections, while the three drivers support outgoing channels. The always-active monitoring receiver is useful in systems that must detect a remote or peripheral status signal even when automatic shutdown has disabled the normal receiver bank.
Place the device close to the connector and route the exposed driver and receiver pins directly to the protected interface boundary. Keep logic-side traces away from cable-side pins, provide a stable ground reference, and follow the manufacturer application guidance for bypass capacitors and charge-pump capacitors. Verify signal polarity, direction, and shutdown behavior in firmware because these details determine how the transceiver should be enabled during communication.
This product page combines the manufacturer family description with package-specific identification, practical interface design guidance, selection criteria, and a verified list of drop-in alternatives. It is intended to help engineers confirm supply compatibility, understand receiver and driver assignments, and determine whether the MAX3243 feature set fits a particular RS-232 design before layout release.
直接替换替代料: MAX3243ECAI+TG1Z ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX3243ECAI+TG1Z (相同外形与封装尺寸) ——差异在于 Product Type, Supply Voltage Range.
MAX3243ECAI+
✅ 直接替换联系询价
查看数据手册 →MAX3243ECAI+TG1Z 规格参数
| Product Type | 3/5 RS-232 transceiver |
| Driver Count | 3 drivers |
| Receiver Count | 5 receivers |
| Always-Active Receiver | 1 complementary always-active receiver |
| Supply Voltage Range | 3.0V to 5.5V |
| AutoShutdown Supply Current | 1 µA |
| Maximum Data Rate | 120 kbit/s |
| Communication Standard | EIA/TIA-232, V.28/V.24 |
| Electrostatic Discharge Protection | Enhanced ESD protection |
| 封装 | 28-pin SSOP |
| 安装类型 | Surface mount |
MAX3243ECAI+TG1Z 28-pin ssop 引脚配置指南
MAX3243ECAI+TG1Z(28-pin ssop 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3243ECAI+TG1Z.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3243ECAI+TG1Z 适用于 6 应用s: Industrial Control Console, Laboratory Data-Acquisition Equipment, POS Terminal and Printer Interface, Service and Configuration Port, Instrument Communication Hub, Legacy Equipment Upgrade.
Industrial Control Console
The MAX3243ECAI+TG1Z fits an industrial control console that must connect a low-voltage controller to several RS-232 peripherals. Its three driver channels can support outbound command or control connections, while five receivers allow multiple status inputs to be monitored. Operation from 3.0V to 5.5V permits use with either 3.3V logic or a 5V interface section, and the 120 kbit/s rate is appropriate for many legacy industrial protocols. The always-active receiver provides a monitoring path when normal AutoShutdown operation is desired. Designers should organize the circuit around cable-side ESD protection, a low-impedance ground reference, and the manufacturer-recommended bypass and charge-pump capacitors.
Laboratory Data-Acquisition Equipment
The MAX3243ECAI+TG1Z is useful in laboratory instruments that exchange commands and measurements with older RS-232 equipment. A three-driver configuration can provide separate transmit paths, while the five-receiver arrangement gives the instrument more incoming status channels than a basic 2/1 transceiver. The MAX3243 family operates from 3.0V to 5.5V and supports up to 120 kbit/s, matching many instrument-control interfaces. Automatic shutdown lowers supply current to 1 µA when receiver inputs remain inactive, which is beneficial in bench equipment with intermittent communication. The interface should be placed near the external connector so cable transients are not propagated into sensitive measurement circuitry.
POS Terminal and Printer Interface
The MAX3243ECAI+TG1Z can support point-of-sale equipment with a mix of printer, reader, and service connections. Three drivers cover outbound channels, and the additional receivers can monitor equipment status without requiring several separate RS-232 interface packages. Its 120 kbit/s maximum data rate accommodates the serial communication speeds commonly used by legacy retail peripherals. Operating from 3.0V to 5.5V also allows the interface to share either 3.3V or 5V system rails. Because retail peripherals can expose long or poorly grounded cables, the PCB should keep the cable-side route short, include the required protection network, and maintain a common ground reference according to the manufacturer guidance.
Service and Configuration Port
The MAX3243ECAI+TG1Z is appropriate for a service port that combines command transmission with several diagnostic inputs. The three driver outputs can support configuration or control traffic, while five receiver inputs can collect readiness, fault, and interlock signals. The always-active receiver is especially valuable when an external monitor must remain responsive even if the principal receivers enter AutoShutdown. A supply range of 3.0V to 5.5V supports low-voltage embedded controllers, and the 1 µA shutdown current reduces standby demand. Firmware should explicitly control enable and shutdown behavior, and hardware should use separate protection and routing practices for logic-side and cable-side nets.
Instrument Communication Hub
The MAX3243ECAI+TG1Z fits a communication hub that must consolidate multiple RS-232 links around a processor or FPGA. Three drivers support outbound ports, and five receivers support inbound channels, reducing the number of separate transceiver packages needed. The 120 kbit/s rate is suitable for many legacy instrument links, while 3.0V-to-5.5V operation provides flexibility in mixed-voltage systems. The always-active monitoring receiver can track an external device without waking the main receiver bank. Engineers should assign directions explicitly, avoid simultaneous driver conflicts, and validate cable length, ground reference, and logic levels against each connected peripheral before deploying the hub.
Legacy Equipment Upgrade
The MAX3243ECAI+TG1Z can modernize a controller that must retain compatibility with legacy RS-232 equipment while using a 3.3V or 5V logic supply. The device provides three drivers, five receivers, enhanced ESD protection, automatic shutdown, and a maximum data rate of 120 kbit/s in a 28-pin SSOP. This combination allows a new controller to retain older peripheral connections without redesigning every cable and protocol. The transition should begin with a complete pinout comparison against the previous transceiver, followed by checks of receiver thresholds, driver polarity, shutdown timing, and external capacitor values. Field cabling should remain on the protected side of the connector.
工程参考数据: MAX3243ECAI+TG1Z ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3243ECAI+ |
|---|---|---|
| Package | 28-pin SSOP | 28-pin SSOP - same |
| Brand | Analog Devices | Analog Devices |
| Product Type | 3/5 RS-232 transceiver | 3/5 RS-232 transceiver |
| Driver Count | 3 drivers | 3 drivers |
| Receiver Count | 5 receivers | 5 receivers |
| Supply Voltage Range | 3.0V to 5.5V | 3.0V to 5.5V |
| Maximum Data Rate | 120 kbit/s | 120 kbit/s |
| AutoShutdown Supply Current | 1 µA | 1 µA |
| ESD Protection | Enhanced ESD protection | Enhanced ESD protection |
关键差异点
- Greater receiver count than a conventional 2/1 interface (对比 MAX3221CAE+TG1Z)
- Always-active monitoring receiver (对比 MAX3243ECAI+)
- Low-power automatic shutdown behavior (对比 MAX3221EAE+TG1Z)
设计说明
Place the MAX3243ECAI+TG1Z close to the external connector and route driver and receiver pins directly toward the protected cable-side boundary. Keep the always-active monitoring receiver and logic-side inputs away from switching nodes and fast digital traces. Use a continuous ground reference beneath and around the interface area, and preserve the manufacturer's recommended bypass and charge-pump capacitor placement to minimize loop area.
Use the manufacturer's specified capacitor values and polarity for the charge-pump and supply bypass networks. The interface operates from 3.0V to 5.5V, so verify that the selected system rail remains within range during startup, shutdown, and regulator tolerance. Do not substitute capacitors without checking ESR, voltage rating, and stability because charge-pump behavior and supply current can be affected by component characteristics.
Do not treat the MAX3243 channel count as interchangeable with a 2/1 RS-232 transceiver even when both use 28-pin packages. Confirm each driver and receiver connection against the manufacturer pin table, including the complementary always-active receiver. Also verify enable and shutdown polarity in firmware, since an incorrectly controlled interface can prevent wakeup or leave a driver in an unexpected state.
External RS-232 cables can inject electrostatic-discharge and switching transients into the interface. Keep exposed connector nets short, provide the required protection network, and maintain a low-impedance return path to the interface ground. Avoid routing cable-side signals beneath sensitive logic or analog sections of the PCB, and test the complete assembled board under realistic cable lengths and grounding conditions.
合规信息
No explicit compliance declaration was identified in the product-specific information. AEC-Q100 is not applicable to this general-purpose RS-232 interface transceiver.