MAX3243IPWRG4 - 250kbps RS-232 Transceiver | Texas Instruments
料号: MAX3243IPWRG4 ✓ 量产中MAX3243IPWRG4 概述
An RS-232 transceiver is an interface IC that converts between single-ended, bipolar logic-level signals used by host systems and the differential voltage signaling required by RS-232 equipment. Within the interface hierarchy, the MAX3243 combines a line driver, line receiver, voltage-level translation, and electrostatic-discharge protection into one low-voltage CMOS device. This integration reduces board area and component count while maintaining compatibility with powered-down portable and industrial equipment.
The MAX3243IPWRG4 operates from 3 V to 5.5 V, making it suitable for systems using either 3.3 V or 5 V power rails. Its 250 kbps maximum data rate supports standard serial links used for instrumentation, industrial control, point-of-sale equipment, and data acquisition. The 28-pin TSSOP package has a stated 0.65 mm terminal pitch and 5.30 mm body width, enabling compact surface-mount layouts where a larger package would be inconvenient.
AutoShutdown provides an important power-management advantage for portable and intermittently connected systems. When the receiver detects no valid RS-232 signal, the device can enter a shutdown state and reduce supply current to 1 uA. Resume timing and capacitor sizing should still be evaluated against the system communication protocol, particularly when the remote transmitter can remain connected but idle for long periods.
Typical uses include industrial serial controllers, laboratory interfaces, barcode scanners, security equipment, and embedded service ports. The three-driver, three-receiver arrangement works well for compact dual-ended links, while the protected low-voltage interface suits systems that need reliable translation between CMOS logic and RS-232 levels. Designers should account for the voltage levels and grounding requirements of the connected RS-232 equipment when evaluating signal integrity.
Place the device close to the connector and use short, appropriately terminated signal routes for the highest practical noise immunity. Follow the manufacturer datasheet for external charge-pump capacitors, driver output wiring, receiver input handling, and ESD layout. Verify that the power rail, logic levels, line-direction control, and operating temperature meet the complete system requirements before releasing the PCB.
This product record combines electrical specifications, package details, pin-location guidance, application fit, and qualified drop-in comparison information. It also highlights practical power-management and layout considerations so engineers can assess the MAX3243IPWRG4 against other RS-232 interface choices before committing to a board design.
直接替换替代料: MAX3243IPWRG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX3243IPWRG4 (相同外形与封装尺寸) ——差异在于 ESD Protection, Maximum Data Rate.
MAX3243EIPWRG4
✅ 直接替换联系询价
查看数据手册 →MAX3243EPWRG4
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX3243CPWRG4
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX3243ECPWG4
✅ 直接替换联系询价
查看数据手册 →MAX3243EUPWRG4
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX3243IPWRG4 规格参数
| 接口类型 | RS-232 line driver and receiver |
| Number of Drivers | 3 |
| Number of Receivers | 3 |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | ±15 kV HBM |
| Shutdown Supply Current | 1 uA |
| Process Technology | CMOS |
| Device Type | Multichannel transceiver |
| Package Type | 28-pin TSSOP |
| Package Body Width | 5.30 mm |
| Terminal Pitch | 0.65 mm |
| Number of Terminals | 28 |
| 安装类型 | Surface mount |
| Maximum Transmit Delay | 150 ns |
| 工作温度范围 | 0 °C to 70 °C |
MAX3243IPWRG4 5.30 mm 引脚配置指南
MAX3243IPWRG4(5.30 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3243IPWRG4.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3243IPWRG4 适用于 6 应用s: Industrial Serial Control Interface, Point-of-Sale Terminal, Laboratory Instrument Connectivity, Embedded Service and Configuration Port, Barcode and Identification Equipment, Security and Surveillance Equipment.
Industrial Serial Control Interface
The MAX3243IPWRG4 fits industrial controller and data-acquisition equipment that converts CMOS logic into RS-232 signals. Its 3 V to 5.5 V operating range supports common embedded supply rails, while the 250 kbps rate is appropriate for configuration, logging, and supervisory links. The three-driver and three-receiver arrangement supports several channels without requiring separate transceiver packages. Its 1 uA shutdown current helps reduce standby consumption when the field equipment is connected intermittently.
推荐
Point-of-Sale Terminal
The MAX3243IPWRG4 can serve the serial boundary in a point-of-sale terminal, receipt printer, customer display, or barcode-scanner interface. The 250 kbps maximum rate is more than sufficient for short transactional links, and the 3 V to 5.5 V supply range fits mixed-voltage embedded platforms. AutoShutdown supports lower standby power when a peripheral is disconnected. Designers should verify the remote device’s logic levels, connector wiring, and RS-232 signal polarity before deployment.
推荐
Laboratory Instrument Connectivity
The MAX3243IPWRG4 is appropriate for laboratory instruments that expose a legacy RS-232 configuration or measurement port to a modern controller. Its 250 kbps rate supports short-distance command and measurement traffic, while plus or minus 15 kV HBM protection improves robustness at accessible connector interfaces. The 28-pin TSSOP package conserves board space in multi-channel instruments. Charge-pump capacitors and transceiver routing should follow the manufacturer layout to preserve driver amplitude and noise performance.
推荐
Embedded Service and Configuration Port
The MAX3243IPWRG4 can provide a service port for embedded equipment that needs a legacy RS-232 connection during installation, diagnostics, or firmware recovery. Its low 3 V operating threshold permits use with modern embedded processors, and the 1 uA AutoShutdown current helps isolate inactive ports. The 250 kbps rate is suitable for boot-loader messages and configuration scripts. Firmware should account for transceiver wake-up behavior and avoid assuming that data will be recognized before the interface becomes active.
推荐
Barcode and Identification Equipment
The MAX3243IPWRG4 is suitable for barcode readers, identification terminals, and access-control equipment that communicate through RS-232. The three transmit and three receive channels can support multiple short connections where the connected devices use compatible signaling. A maximum rate of 250 kbps handles command and scanned-data traffic without requiring a higher-bandwidth interface. The protected transceiver is useful near external connectors, while AutoShutdown reduces consumption when an accessory line is not in use.
推荐
Security and Surveillance Equipment
The MAX3243IPWRG4 can support RS-232 commissioning and control links in cameras, access-control panels, and other security equipment. Its plus or minus 15 kV HBM ESD rating adds protection at connector-facing circuitry, while the 3 V to 5.5 V range supports low-power embedded platforms. The 250 kbps rate is appropriate for command and status traffic rather than continuous high-bandwidth data. Secure installations should also use shielded cables, controlled grounding, and connector practices appropriate to the RS-232 environment.
推荐
推荐产品汇总
工程参考数据: MAX3243IPWRG4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3243EIPWRG4 | MAX3243EPWRG4 | MAX3243CPWRG4 | MAX3243ECPWG4 | MAX3243EUPWRG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Interface Type | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver | RS-232 transceiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| Driver and Receiver Count | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers | 3 drivers and 3 receivers |
| Operating Temperature Range | 0 °C to 70 °C | Approximately -40 °C to 85 °C | Approximately -40 °C to 85 °C | Approximately 0 °C to 70 °C | Approximately -40 °C to 85 °C | Approximately -40 °C to 85 °C |
关键差异点
- Lower-voltage RS-232 interface (对比 MAX3243EIPWRG4)
- Commercial-temperature grade for controlled installations (对比 MAX3243EIPWRG4)
- Integrated low-power shutdown behavior (对比 MAX3243CPWRG4)
设计说明
Place the MAX3243IPWRG4 close to the RS-232 connector and route driver and receiver lines away from switching nodes and fast digital clocks. Keep the charge-pump capacitor connections short and follow the Texas Instruments MAX3243 datasheet layout and capacitor values exactly. The interface is designed for 250 kbps operation, but long unprotected cable runs can introduce noise and reflections that are not problems at lower logic speeds, so connector-side grounding and cable shielding must be considered.
Confirm that the 3 V to 5.5 V supply remains within the supported range during startup, shutdown, and remote-power events. The 1 uA AutoShutdown current is a standby figure, not the operating current, so calculate the average power from normal load current, transceiver activity, and shutdown duration. If the connected RS-232 source remains active, validate its effect on wake-up timing and the system’s ability to distinguish an inactive port from a disconnected one.
Do not treat every MAX3243 suffix as electrically identical to MAX3243IPWRG4. Temperature grade, ESD behavior, package dimensions, and ordering codes can differ between E, C, and EU variants. Before substitution, compare the 28-pin PW package drawing, all pin names, supply range, charge-pump capacitor requirements, shutdown behavior, and temperature limits. Also verify that a lead-free ordering code does not imply a different electrical grade merely because the suffix characters differ.
Use the manufacturer’s specified charge-pump capacitors and observe the recommended placement because RS-232 driver amplitude depends on the voltage generated by the charge-pump network. Keep these traces short and return currents controlled to reduce radiated noise. For remote cables, use appropriate shielding and ground references; a logic-level UART trace and an RS-232 line are electrically different interfaces and should not be treated as interchangeable connections.
合规信息
The MAX3243 datasheet identifies plus or minus 15 kV HBM ESD protection, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were identified. AEC-Q100 qualification is not applicable to this RS-232 interface device.