MAX396EPI+ - 16:1 100Ohm CMOS Analog Multiplexer | Analog Devices
料号: MAX396EPI+ ✓ 量产中MAX396EPI+ 概述
An analog multiplexer is an interface IC that connects multiple analog signal sources to a shared processing channel. The MAX396 belongs to the broader analog switch and multiplexer hierarchy, where switch resistance, channel matching, charge injection, leakage, and supply voltage determine how accurately a selected signal reaches the output. This makes the device suitable for precision measurement, data acquisition, test equipment, and industrial control systems.
The MAX396EPI+ provides maximum on-resistance of 100 ohms, with on-resistance matching between switches maintained within 6 ohms. Its on-resistance remains flat over the specified signal range, with a maximum variation of 10 ohms. These characteristics make channel resistance less dependent on signal amplitude than in some multiplexers and support repeatable analog measurements. Charge injection is limited to 5 pC maximum.
The low-voltage silicon-gate CMOS process supports low-power operation while providing fast switching. The multiplexer retains CMOS-logic input compatibility and includes electrostatic-discharge protection greater than 2,000 V per Method 3015.7. Single-supply operation supports +2.7 V to +16 V systems, while dual-supply operation permits bipolar signal ranges of ±2.7 V to ±8 V.
Typical applications include multiplexed data acquisition, sensor signal routing, automated test systems, industrial measurement interfaces, and control systems that must connect several low-voltage analog inputs to one downstream converter or amplifier. Single-supply operation is convenient for compact equipment, whereas dual supplies allow the device to process signals around ground.
When laying out a circuit, keep analog traces short and provide a stable ground reference. Place input and supply decoupling capacitors close to the device, and confirm that the selected signal amplitude, common-mode range, and switching frequency remain within the electrical limits of the application.
This page organizes the key MAX396EPI+ specifications, pin-compatible replacement options, application guidance, and practical design considerations to support faster component selection and PCB implementation.
直接替换替代料: MAX396EPI+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX396EPI+ (相同外形与封装尺寸) ——差异在于 Multiplexer Configuration, Maximum Charge Injection, Maximum On-Resistance, ESD Protection, Logic Compatibility.
MAX396CPI+
✅ 直接替换联系询价
查看数据手册 →MAX396EPI
✅ 直接替换📋 参考替代料(不在目录中)
MAX397CPI+
✅ 直接替换联系询价
查看数据手册 →MAX396EPI+ 规格参数
| Product Type | 1-circuit 16:1 analog multiplexer |
| Multiplexer Configuration | 16:1 |
| Maximum On-Resistance | 100 ohms |
| On-Resistance Matching Between Channels | 6 ohms maximum |
| On-Resistance Variation Over Signal Range | 10 ohms maximum |
| Maximum Charge Injection | 5 pC |
| Single-Supply Operating Range | +2.7 V to +16 V |
| Dual-Supply Operating Range | ±2.7 V to ±8 V |
| Logic Compatibility | CMOS logic input compatible |
| ESD Protection | Greater than 2,000 V per Method 3015.7 |
| Process Technology | Low-voltage silicon-gate CMOS |
| 封装 | 28-pin PDIP |
| 安装类型 | Through-hole |
| AEC-Q100 Qualification | Not applicable |
MAX396EPI+ 28-pin pdip 引脚配置指南
MAX396EPI+(28-pin pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX396EPI+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX396EPI+ 适用于 6 应用s: Multiplexed Data Acquisition, Industrial Sensor Signal Routing, Automated Test Equipment, Precision Voltage Measurement, Battery-Powered Instrument, Bipolar Control Signal Interface.
Multiplexed Data Acquisition
The MAX396EPI+ fits data-acquisition front ends that must connect one of 16 low-voltage sensor inputs to a shared ADC or instrumentation amplifier. Its 100-ohms maximum on-resistance limits channel loading, while matching within 6 ohms helps maintain calibration consistency across selected sources. The low 5-pC maximum charge injection is also useful when the multiplexer sits near a sampling network. Place the device close to the analog input bus, keep traces short, and validate source settling against the ADC acquisition window. The same 16:1 structure simplifies address decoding compared with a bank of discrete switches.
推荐
Industrial Sensor Signal Routing
The MAX396EPI+ is suitable for industrial sensor interfaces that must route temperature, pressure, strain, or position signals from multiple channels into one measurement path. Operation from +2.7 V to +16 V supports both compact low-voltage systems and higher-voltage industrial rails, while ±2.7 V to ±8 V dual supplies support bipolar transducer signals. Its 6-ohm maximum channel-to-channel matching helps reduce gain variation when changing measurement sources. Use a single ground reference, keep high-impedance sensor paths short, and confirm common-mode limits for the selected supply configuration.
推荐
Automated Test Equipment
The MAX396EPI+ can reduce the number of discrete relays required in automated test equipment by selecting one of 16 test points for a common measurement chain. Its 100-ohms maximum on-resistance, low channel variation, and 5-pC maximum charge injection provide predictable behavior when connecting sources, dividers, or stimulus-return paths. The device’s CMOS-compatible address inputs simplify control from common test-controller logic. For precision measurements, verify leakage, off-state isolation, switching time, and settling behavior against the instrumentation settling requirements.
推荐
Precision Voltage Measurement
The MAX396EPI+ is appropriate for precision voltage measurement when several input ranges must share a single amplifier or converter. On-resistance matching within 6 ohms reduces variation introduced by the selected switch, while the maximum 10-ohm variation over the signal range supports consistent channel behavior. With a +5 V single supply, the mux fits low-voltage analog boards; with ±5 V dual supplies, it can accept signals around ground. Confirm that the downstream amplifier’s input bias current and the mux’s leakage do not create unacceptable errors at the required measurement accuracy.
推荐
Battery-Powered Instrument
The MAX396EPI+ can serve battery-powered instruments when low-voltage operation and compact analog routing are priorities. Its single-supply range begins at +2.7 V, allowing operation from a 3.3 V system without dual negative rails, while the 16:1 configuration replaces many point-to-point switch paths. The low-voltage CMOS implementation supports portable measurement equipment, although the exact quiescent current and switching energy must be checked for duty-cycle calculations. Use local supply decoupling and avoid long unprotected analog traces to preserve measurement integrity.
推荐
Bipolar Control Signal Interface
The MAX396EPI+ fits control systems that must select among bipolar command or feedback signals referenced to ground. Dual-supply operation from ±2.7 V to ±8 V permits the switch to handle signals below and above ground while retaining CMOS-compatible address logic. The 100-ohms maximum on-resistance provides a defined insertion resistance for downstream receivers, and the 5-pC maximum charge injection limits control pulses when switching sensitive analog nodes. Validate signal amplitude, common-mode range, and logic thresholds, then keep the analog and digital return paths joined at a controlled ground point.
推荐
推荐产品汇总
工程参考数据: MAX396EPI+ ——对比、设计指导和合规信息。
选型指南
Use the MAX396CPI+ when the same electrical and package family is needed for commercial-temperature production after checking the required temperature range. The MAX396EPI is relevant for legacy procurement because it retains the same 28-PDIP footprint and core MAX396 characteristics.
Consider the MAX397CPI+ only when a dual 8-channel arrangement is acceptable, and confirm its truth table. The DG406DJ+ and DG407DJ+ are pin-compatible sourcing alternatives identified by the manufacturer, but their different channel configurations mean that address decoding, truth-table behavior, leakage, switching speed, and electrical limits must be reviewed before substitution.
与替代料对比
| 参数 | 本产品 | MAX396CPI+ | MAX396EPI | MAX397CPI+ | DG406DJ+ | DG407DJ+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-PDIP | 28-PDIP | 28-PDIP | 28-PDIP | 28-PDIP | 28-PDIP |
| Multiplexer Configuration | 16:1 | 16:1 | 16:1 | Dual 8-channel | 4:1 or dual 4:1 | 4:1 or dual 4:1 |
关键差异点
- Single 16:1 multiplexing arrangement (对比 DG407DJ+)
- Defined channel-to-channel resistance matching (对比 DG406DJ+)
- Low charge injection for analog switching (对比 MAX396EPI)
- Single and dual low-voltage supply operation (对比 MAX397CPI+)
设计说明
Route the 16 analog inputs and common analog output as compact, quiet traces, with the mux positioned close to the sensor or measurement source. Long traces can act as antenna-like pickup paths and add resistance that becomes significant beside the specified 100-ohms maximum on-resistance. Keep digital address lines away from the analog output, provide a continuous ground plane, and place supply-decoupling capacitors near the power pins.
Check source impedance and downstream capacitance before selecting the mux. The 100-ohms maximum on-resistance combines with source resistance and wiring capacitance to form an RC settling network, so a nominally correct switch may require extra acquisition time at high source impedances. For low-current or capacitor-based sensors, also evaluate the 5-pC maximum charge injection because each address transition can create a voltage transient.
Decouple the supply pins locally and select bypass values that suppress ripple on both the single-supply and dual-supply rails used by the design. The device accepts +2.7 V to +16 V or ±2.7 V to ±8 V, but the allowed signal range remains tied to the selected supply configuration. Verify address-logic levels, output limits, and injected switching transients against the exact operating mode in the manufacturer data sheet.
Do not substitute MAX397, DG406, or DG407 parts solely because they use a compatible 28-pin footprint. The MAX397 uses a dual 8-channel arrangement, while the DG406 and DG407 families have different channel configurations and truth tables. Confirm address mapping, selected-channel behavior, electrical limits, temperature grade, and package suffix before treating any listed alternative as a production drop-in replacement.
合规信息
The manufacturer data sheet identifies ESD protection greater than 2,000 V per Method 3015.7. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses were not established from the cited product information.