MAX3490ECSA+T - 12Mbps RS-485/RS-422 Transceiver | Analog Devices
料号: MAX3490ECSA+T ✓ 量产中MAX3490ECSA+T 概述
An RS-485/RS-422 transceiver is an interface IC that converts between CMOS/TTL logic levels and balanced differential signals. It belongs to the transceiver hierarchy within interface ICs, where differential signaling improves noise immunity and allows reliable communication over longer cable distances than ordinary single-ended logic. The MAX3490E family combines low-power 3.3 V operation, fault-tolerant differential drivers, and enhanced electrostatic-discharge protection for industrial and instrumentation networks.
Key features include operation from a single 3.3 V supply, a 12 Mbps maximum signaling rate, ±15 kV ESD protection on the bus pins, and one transmit and one receive channel per device. The partially slew-rate-limited driver helps control edge rates, reducing reflections and radiated emissions on suitable terminated networks. The receiver provides differential input detection for RS-422 links, while the device can also participate in half-duplex RS-485 networks when its direction-control interface is used correctly.
The MAX3490E series belongs to the MAX3483E family of low-power transceivers. Its internal architecture combines a differential line driver, a differential receiver, bus-direction logic, and protection structures within one compact package. This integration reduces the number of discrete components required for isolated or non-isolated industrial links while preserving a standardized differential bus interface. Designers must still provide appropriate termination, biasing, protection, and grounding for the selected RS-422 or RS-485 topology.
Typical uses include industrial sensor networks, programmable logic controller communication, building-automation equipment, test and measurement instruments, data-acquisition modules, and embedded serial links. It is particularly useful when a compact PCB area, 3.3 V supply, moderate-to-high data rates, and direct-contact ESD robustness are required. The 8-pin SOIC footprint also simplifies assembly in designs already using surface-mount interface components.
Design considerations include placing the transceiver close to the connector, maintaining a continuous ground reference between the logic side and the cable interface, and using the termination method appropriate to the topology. Differential pairs should be routed with consistent geometry, while surge or isolation components may be required when the cable leaves the protected enclosure. Verify signal polarity, driver-enable logic, receiver output levels, and supply sequencing before releasing a new PCB.
This page combines the manufacturer's product specifications, package and interface guidance, comparison criteria, and practical PCB considerations to support faster engineering evaluation of the MAX3490ECSA+T in industrial communications designs.
直接替换替代料: MAX3490ECSA+T ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX3490ECSA+T (相同外形与封装尺寸) ——差异在于 Maximum Data Rate, ESD Protection, Driver Type, Package, Supply Voltage.
MAX3490EESA+T
✅ 直接替换联系询价
查看数据手册 →MAX3490AEGSA+T
✅ 直接替换联系询价
查看数据手册 →MAX3483EESA+T
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX3485EESA+T
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX3486EESA+T
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MAX3488EESA+T
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MAX3490ECSA+T 规格参数
| Product Type | RS-485/RS-422 transceiver |
| 电源电压 | 3.3 V |
| Maximum Data Rate | 12 Mbps |
| ESD Protection | ±15 kV |
| Number of Drivers | 1 |
| Number of Receivers | 1 |
| Driver Type | Slew-rate-limited differential driver |
| Supported Standards | RS-485 and RS-422 |
| Low-Power Operation | 3.3 V low-power transceiver |
| 封装 | 8-pin SOIC |
| 安装类型 | Surface mount |
| 生命周期状态 | Production |
| Datasheet Revision | Rev. 1 |
MAX3490ECSA+T 8-pin soic 引脚配置指南
MAX3490ECSA+T(8-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3490ECSA+T.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3490ECSA+T 适用于 6 应用s: Industrial Sensor Networking, PLC and Factory Automation Communication, Building Automation Equipment, Data Acquisition and Test Equipment, Embedded Serial Communication, Instrumentation and Remote Sensor Links.
Industrial Sensor Networking
The MAX3490ECSA+T fits 3.3 V industrial sensor links that need one differential transmitter and one receiver in a compact 8-pin SOIC footprint. Its 12 Mbps maximum data rate supports short, high-speed field buses, while the slew-rate-limited driver helps control edge rates and reduce ringing. The ±15 kV ESD rating adds useful protection for bus nodes connected to external wiring. Confirm the required temperature grade and add external surge protection when cables leave the equipment enclosure.
推荐
PLC and Factory Automation Communication
Use the MAX3490ECSA+T as the bus-interface element between a 3.3 V controller and an RS-485 or RS-422 factory network. One integrated driver and receiver support bidirectional half-duplex RS-485 or dedicated RS-422 signaling, while 12 Mbps operation provides ample bandwidth for controller-to-module traffic. The partial slew-rate limitation favors cleaner edges and reduced EMI in cabinet installations. Validate address, biasing, termination, and isolation requirements for the complete bus topology.
推荐
Building Automation Equipment
The MAX3490ECSA+T is appropriate for building-automation controllers, room modules, and field interfaces using balanced RS-485 communication. Its 3.3 V supply supports compact mixed-signal controller boards, and the 8-pin SOIC package preserves PCB area for sensors and communications isolation. Differential signaling improves noise immunity over building wiring, while ±15 kV ESD protection strengthens the interface against charged-contact events. Select termination, common-mode grounding, and surge protection according to the installed cable environment.
推荐
Data Acquisition and Test Equipment
The MAX3490ECSA+T can connect laboratory instruments, automated test systems, and data-acquisition modules to RS-485 or RS-422 controllers. The 12 Mbps rate supports high-throughput instrument traffic over short qualified cables, and the single-channel driver and receiver simplify protocol-specific interfaces. Its compact SOIC package is useful when analog and digital sections compete for board space. Preserve controlled edge rates, use a proper ground reference, and isolate external test leads when operators may contact the chassis.
推荐
Embedded Serial Communication
The MAX3490ECSA+T adds a robust differential bus port to embedded equipment operating from a 3.3 V rail. One driver and one receiver are sufficient for compact half-duplex RS-485 nodes or point-to-point RS-422 links, avoiding the area required by a larger multi-channel transceiver. The 12 Mbps capability can accommodate fast local links, while controlled slew rates assist signal integrity. Review enable timing and receiver-output behavior against the host UART or communications controller.
推荐
Instrumentation and Remote Sensor Links
The MAX3490ECSA+T suits remote sensor and instrumentation links where a compact differential interface is needed close to a cable connector. Its 3.3 V operation reduces system supply complexity, while ±15 kV ESD protection strengthens a frequently exposed interface. The partially slew-rate-limited driver can reduce ringing on correctly terminated cables, although network geometry remains critical. Place the transceiver near the connector, maintain a continuous ground reference, and consider galvanic isolation for long or externally accessible wiring.
推荐
推荐产品汇总
工程参考数据: MAX3490ECSA+T ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3490EESA+T | MAX3490AEGSA+T | MAX3483EESA+T | MAX3485EESA+T |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package | 8-pin SOIC - same package |
| Function | 1/1 RS-485/RS-422 transceiver | 1/1 RS-485/RS-422 transceiver | 1/1 RS-485/RS-422 transceiver | 1/1 MAX3483E-family transceiver | 1/1 MAX3483E-family transceiver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Maximum Data Rate | 12 Mbps | 12 Mbps | 12 Mbps | 12 Mbps | 12 Mbps |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV | ±15 kV | ±15 kV |
| Driver and Receiver Count | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver | 1 driver, 1 receiver |
| Slew-Rate-Limited Driver | Yes, partial slew-rate limiting | Yes, partial slew-rate limiting | Yes, partial slew-rate limiting | Yes | Yes |
关键差异点
- High-speed differential operation in a compact interface (对比 MAX3490EESA+T)
- Controlled driver edges for cleaner bus transitions (对比 MAX3483EESA+T)
- Direct-contact ESD robustness on external bus nodes (对比 MAX3490AEGSA+T)
设计说明
Place the MAX3490ECSA+T close to the external communication connector so the protected bus pins connect to the cable through a short, controlled path. Keep the logic-side traces away from the bus-side connector and protection components. Maintain a continuous ground reference along the interface, and use a ground-plane connection that does not interrupt the differential signal return path.
Treat the bus as a controlled-impedance differential channel. Terminate only at the locations required by the RS-422 or RS-485 topology, using the value recommended by the manufacturer for the selected network. Avoid long unmatched stubs, maintain consistent pair geometry, and verify edge ringing with an oscilloscope at the intended data rate before increasing cable length or node count.
Do not assume that every member of the MAX3483E family is automatically interchangeable. Confirm the exact driver-enable behavior, receiver polarity, shutdown or enable pins, supply requirements, and bus-pin protection against the manufacturer pin-description table. For RS-485 multidrop networks, also verify fail-safe biasing and ensure that the transceiver is never enabled in a way that conflicts with another transmitter on the bus.
The partial slew-rate limitation can reduce ringing and radiated emissions, but EMI performance still depends on cable length, data pattern, termination, and connector return paths. Keep the differential pair compact and continuous, avoid parallel runs with switching-power nodes, and test the assembled board in its final enclosure with representative traffic. Additional filtering should be selected from measured spectra rather than added indiscriminately.
Although the MAX3490ECSA+T is a low-power 3.3 V transceiver, the complete assembly must remain within the manufacturer's specified operating and junction-temperature limits. Provide exposed PCB copper around the SOIC where practical, avoid placing it immediately beside a regulator hotspot, and account for enclosure temperature rise. Verify worst-case dissipation with the actual supply, termination, loading, and data activity.
合规信息
The accessible product and comparison information does not provide a definitive compliance statement for this exact ordering suffix. Compliance fields remain unknown pending confirmation in the manufacturer's product-selection table or material declaration.