MAX352EPE - Quad 35Ω SPST Analog Switch | Maxim Integrated
料号: MAX352EPE ✓ 量产中MAX352EPE 概述
An analog switch is an integrated semiconductor device that connects or disconnects signal paths under digital control. The MAX352 belongs to the broader hierarchy of analog switches, analog multiplexers, interface ICs, and semiconductor signal-routing components. Unlike a mechanical relay, it changes connection state electronically, allowing compact equipment with fast and repeatable routing. Each of its four switches is normally open, so the default state provides signal-path isolation rather than a permanently connected route.
Key characteristics include four SPST channels, 1:1 signal routing, and a maximum specified on-resistance of 35Ω. The EPE suffix identifies the 16-pin PDIP industrial-temperature ordering variant. The device is supplied as a through-hole package, making it appropriate for legacy boards, instrumentation, control systems, and prototypes where a surface-mount footprint would be inconvenient. The product family is produced by Maxim Integrated, whose product portfolio is now represented by Analog Devices.
The MAX352’s four normally open switches make it useful for source selection, signal isolation, test-point routing, and external-interface switching. Each channel can independently connect its designated terminal pair when the corresponding control input is asserted. Because it is a unilateral 1:1 routing element, the switch should be evaluated for signal amplitude, source impedance, leakage, charge injection, and off-state behavior according to the manufacturer data sheet.
The MAX352 is especially relevant when rebuilding or maintaining equipment that already specifies a 16-pin quad-SPST analog switch. Because pin compatibility and electrical equivalence must be confirmed at the exact terminal and control level, engineers should compare the full data sheet rather than relying only on the package outline. The 35Ω resistance can be significant for high-impedance precision measurements, while it may remain acceptable for control, sensor, audio, or low-frequency instrumentation signals.
A practical layout should route sensitive analog conductors away from digital control traces, maintain a common ground reference, and place protection or filtering components where they do not degrade switch isolation. The MAX352EPE is also the exact 16-pin PDIP member to select when a MAX352 function is required and the board does not provide SMD pads.
This page combines the manufacturer family information with verified distributor packaging details, replacement analysis, application guidance, and design considerations for engineers maintaining or reproducing a MAX352EPE-based circuit.
直接替换替代料: MAX352EPE ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX352EPE (相同外形与封装尺寸) ——差异在于 Package, Switch Configuration.
MAX352CPE+
✅ 直接替换联系询价
查看数据手册 →MAX352EPE 最大额定值与电气特性
| Product Type | Precision quad SPST analog switch |
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 |
| Number of Channels | 4 channels |
| Switch Type | Single-pole single-throw (SPST) |
| Default Switch State | Normally open (NO) |
| On-Resistance | 35 ohm maximum |
| 封装 | 16-pin PDIP |
| 安装类型 | Through-hole |
| Temperature Grade | Industrial |
| Number of Terminals | 16 terminals |
| Package Shape | Rectangular |
| Surface Mount | No |
| Production Status | Production |
MAX352EPE rectangular 引脚配置指南
MAX352EPE(rectangular 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX352EPE.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX352EPE 适用于 6 应用s: Legacy Test and Measurement Equipment, Analog Signal Isolation, Sensor and Control Routing, Audio Signal Selection, Automated Interface Switching, Board Repair and Obsolescence Mitigation.
Legacy Test and Measurement Equipment
The MAX352EPE fits repair and modernization work on legacy test equipment because it combines four normally open SPST channels with a 16-pin through-hole footprint. The switches can route test signals, isolate instrument sections, or select external sources without requiring a surface-mount redesign. Its 35Ω maximum on-resistance is practical for many low-frequency measurement and control paths, although precision high-impedance inputs should be checked for loading. Use the manufacturer pin table to preserve the original control polarity and terminal assignments.
推荐
Analog Signal Isolation
The MAX352EPE can isolate an analog signal path when the default normally open state must keep the route disconnected until commanded. Its four independent SPST channels provide practical routing for sensor lines, control outputs, and low-speed instrumentation signals. The 35Ω maximum on-resistance adds series loss and should be considered with the source impedance and receiver input impedance. The DIP package also makes it convenient to socket during repair or characterization work.
推荐
Sensor and Control Routing
The MAX352EPE is suitable for industrial control boards that route several low-frequency sensor or actuator signals through selectable paths. Four normally open switches can isolate channels during calibration, connect redundant inputs, or provide a controlled bypass. The industrial temperature-grade ordering code makes it relevant to equipment operating beyond typical consumer conditions, while the through-hole package supports repairable industrial hardware. Verify supply voltage, control levels, leakage, and switching transients from the data sheet.
推荐
Audio Signal Selection
The MAX352EPE can select or isolate low-level audio paths in laboratory and legacy audio equipment. Four independently controlled normally open channels allow a source to be connected only during the required interval, which can help suppress unwanted paths between switching events. The 35Ω on-resistance may be acceptable for typical low-impedance audio routing, but it is not ideal for very low-noise or high-impedance precision stages. Keep control traces away from the audio conductors to reduce injected noise.
推荐
Automated Interface Switching
The MAX352EPE supports repeatable routing in automated interfaces that connect external equipment to internal measurement circuits. Its four SPST switches can select stimulus sources, disconnect external loads, or form repeatable test paths under digital control. Because it is a 1:1 unilateral switch rather than a multiplexer, each switched pair must have the required driver and receiver arrangement. The 16-pin PDIP footprint is advantageous for older or highly serviceable industrial systems.
推荐
Board Repair and Obsolescence Mitigation
The MAX352EPE provides a practical repair option for boards designed around the original Maxim Integrated MAX352EPE footprint. Installing a MAX352CPE+ can preserve the four normally open SPST functions and the 16-pin terminal arrangement when the original component is unavailable for repair. The substitution should be approved only after checking temperature range, supply conditions, and all device limits. Socketed repair assemblies can simplify inspection and future replacement.
推荐
工程参考数据: MAX352EPE ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX352CPE+ |
|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated |
| Package | 16-pin PDIP | 16-pin PDIP |
| Circuit Count | 4 circuits | 4 circuits |
| Switch Configuration | 1:1 | 1:1 |
| Switch Type | SPST | SPST |
| Default State | Normally open | Normally open |
| Mounting Type | Through-hole | Through-hole |
关键差异点
- Verified same-family mechanical and terminal compatibility (对比 MAX352CPE+)
- Exact industrial-grade ordering option (对比 MAX352CPE+)
- Normally open behavior provides a defined disconnected default state (对比 MAX352CPE+)
设计说明
Treat the 35Ω maximum on-resistance as part of the signal-path impedance, not merely a switching specification. Estimated insertion loss from resistance alone can be calculated as 20 log10[(Rsource + 35Ω + Rload)/(Rsource + Rload)] using the actual source and load impedances. Compare that result with the allowable signal-amplitude error before using the switch for precision measurement or high-value control signals.
Route the switched analog terminals directly between their paired pins and keep unrelated control or digital lines away from these paths. Use a continuous ground plane where the board design permits and place any input filtering or protection close to the receiver. Control traces should be driven cleanly because voltage transitions at the logic inputs can couple into adjacent analog conductors, particularly when the switch handles high-impedance sources.
Do not select the MAX351, MAX352, or MAX353 solely because their packages match. The manufacturer identifies MAX351 as four normally closed switches, MAX352 as four normally open switches, and MAX353 as two normally open plus two normally closed switches. Mixing these default states can reverse a system behavior or create an unintended connection. Also confirm the E ordering suffix against the required operating-temperature range before approving a substitution.
合规信息
The manufacturer product page identifies MAX352 as a production part, but the retrieved information does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 status for the MAX352EPE ordering code. The device is an industrial-grade through-hole analog switch rather than an automotive-qualified ordering variant.