MAX396EPI+ - 16:1 100Ohm CMOS Analog Multiplexer | Analog Devices
MPN: MAX396EPI+ ✓ 啟用中MAX396EPI+ 概覽
An analog multiplexer is an interface IC that connects multiple analog signal sources to a shared processing channel. The MAX396 belongs to the broader analog switch and multiplexer hierarchy, where switch resistance, channel matching, charge injection, leakage, and supply voltage determine how accurately a selected signal reaches the output. This makes the device suitable for precision measurement, data acquisition, test equipment, and industrial control systems.
The MAX396EPI+ provides maximum on-resistance of 100 ohms, with on-resistance matching between switches maintained within 6 ohms. Its on-resistance remains flat over the specified signal range, with a maximum variation of 10 ohms. These characteristics make channel resistance less dependent on signal amplitude than in some multiplexers and support repeatable analog measurements. Charge injection is limited to 5 pC maximum.
The low-voltage silicon-gate CMOS process supports low-power operation while providing fast switching. The multiplexer retains CMOS-logic input compatibility and includes electrostatic-discharge protection greater than 2,000 V per Method 3015.7. Single-supply operation supports +2.7 V to +16 V systems, while dual-supply operation permits bipolar signal ranges of ±2.7 V to ±8 V.
Typical applications include multiplexed data acquisition, sensor signal routing, automated test systems, industrial measurement interfaces, and control systems that must connect several low-voltage analog inputs to one downstream converter or amplifier. Single-supply operation is convenient for compact equipment, whereas dual supplies allow the device to process signals around ground.
When laying out a circuit, keep analog traces short and provide a stable ground reference. Place input and supply decoupling capacitors close to the device, and confirm that the selected signal amplitude, common-mode range, and switching frequency remain within the electrical limits of the application.
This page organizes the key MAX396EPI+ specifications, pin-compatible replacement options, application guidance, and practical design considerations to support faster component selection and PCB implementation.
直接替換替代品,適用於 MAX396EPI+ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MAX396EPI+ (相同外形與佔位) — 差異在於 Multiplexer Configuration, Maximum Charge Injection, Maximum On-Resistance, ESD Protection, Logic Compatibility.
MAX396CPI+
✅ 直接替換聯絡詢價
查看資料表 →MAX396EPI
✅ 直接替換📋 參考替代品(不在目錄中)
MAX397CPI+
✅ 直接替換聯絡詢價
查看資料表 →MAX396EPI+ 規格
| Product Type | 1-circuit 16:1 analog multiplexer |
| Multiplexer Configuration | 16:1 |
| Maximum On-Resistance | 100 ohms |
| On-Resistance Matching Between Channels | 6 ohms maximum |
| On-Resistance Variation Over Signal Range | 10 ohms maximum |
| Maximum Charge Injection | 5 pC |
| Single-Supply Operating Range | +2.7 V to +16 V |
| Dual-Supply Operating Range | ±2.7 V to ±8 V |
| Logic Compatibility | CMOS logic input compatible |
| ESD Protection | Greater than 2,000 V per Method 3015.7 |
| Process Technology | Low-voltage silicon-gate CMOS |
| 封裝 | 28-pin PDIP |
| 安裝類型 | Through-hole |
| AEC-Q100 Qualification | Not applicable |
MAX396EPI+ 28-pin pdip 腳位配置指南
MAX396EPI+(28-pin pdip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: MAX396EPI+.
請參閱 資料表 以查看完整腳位配置。
典型應用
MAX396EPI+ 適用於 6 應用s: Multiplexed Data Acquisition, Industrial Sensor Signal Routing, Automated Test Equipment, Precision Voltage Measurement, Battery-Powered Instrument, Bipolar Control Signal Interface.
Multiplexed Data Acquisition
The MAX396EPI+ fits data-acquisition front ends that must connect one of 16 low-voltage sensor inputs to a shared ADC or instrumentation amplifier. Its 100-ohms maximum on-resistance limits channel loading, while matching within 6 ohms helps maintain calibration consistency across selected sources. The low 5-pC maximum charge injection is also useful when the multiplexer sits near a sampling network. Place the device close to the analog input bus, keep traces short, and validate source settling against the ADC acquisition window. The same 16:1 structure simplifies address decoding compared with a bank of discrete switches.
推薦
Industrial Sensor Signal Routing
The MAX396EPI+ is suitable for industrial sensor interfaces that must route temperature, pressure, strain, or position signals from multiple channels into one measurement path. Operation from +2.7 V to +16 V supports both compact low-voltage systems and higher-voltage industrial rails, while ±2.7 V to ±8 V dual supplies support bipolar transducer signals. Its 6-ohm maximum channel-to-channel matching helps reduce gain variation when changing measurement sources. Use a single ground reference, keep high-impedance sensor paths short, and confirm common-mode limits for the selected supply configuration.
推薦
Automated Test Equipment
The MAX396EPI+ can reduce the number of discrete relays required in automated test equipment by selecting one of 16 test points for a common measurement chain. Its 100-ohms maximum on-resistance, low channel variation, and 5-pC maximum charge injection provide predictable behavior when connecting sources, dividers, or stimulus-return paths. The device’s CMOS-compatible address inputs simplify control from common test-controller logic. For precision measurements, verify leakage, off-state isolation, switching time, and settling behavior against the instrumentation settling requirements.
推薦
Precision Voltage Measurement
The MAX396EPI+ is appropriate for precision voltage measurement when several input ranges must share a single amplifier or converter. On-resistance matching within 6 ohms reduces variation introduced by the selected switch, while the maximum 10-ohm variation over the signal range supports consistent channel behavior. With a +5 V single supply, the mux fits low-voltage analog boards; with ±5 V dual supplies, it can accept signals around ground. Confirm that the downstream amplifier’s input bias current and the mux’s leakage do not create unacceptable errors at the required measurement accuracy.
推薦
Battery-Powered Instrument
The MAX396EPI+ can serve battery-powered instruments when low-voltage operation and compact analog routing are priorities. Its single-supply range begins at +2.7 V, allowing operation from a 3.3 V system without dual negative rails, while the 16:1 configuration replaces many point-to-point switch paths. The low-voltage CMOS implementation supports portable measurement equipment, although the exact quiescent current and switching energy must be checked for duty-cycle calculations. Use local supply decoupling and avoid long unprotected analog traces to preserve measurement integrity.
推薦
Bipolar Control Signal Interface
The MAX396EPI+ fits control systems that must select among bipolar command or feedback signals referenced to ground. Dual-supply operation from ±2.7 V to ±8 V permits the switch to handle signals below and above ground while retaining CMOS-compatible address logic. The 100-ohms maximum on-resistance provides a defined insertion resistance for downstream receivers, and the 5-pC maximum charge injection limits control pulses when switching sensitive analog nodes. Validate signal amplitude, common-mode range, and logic thresholds, then keep the analog and digital return paths joined at a controlled ground point.
推薦
推薦產品摘要
工程參考資料,適用於 MAX396EPI+ — 比較、設計指引及合規資訊。
選型指南
Use the MAX396CPI+ when the same electrical and package family is needed for commercial-temperature production after checking the required temperature range. The MAX396EPI is relevant for legacy procurement because it retains the same 28-PDIP footprint and core MAX396 characteristics.
Consider the MAX397CPI+ only when a dual 8-channel arrangement is acceptable, and confirm its truth table. The DG406DJ+ and DG407DJ+ are pin-compatible sourcing alternatives identified by the manufacturer, but their different channel configurations mean that address decoding, truth-table behavior, leakage, switching speed, and electrical limits must be reviewed before substitution.
與替代品比較
| 參數 | 本產品 | MAX396CPI+ | MAX396EPI | MAX397CPI+ | DG406DJ+ | DG407DJ+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-PDIP | 28-PDIP | 28-PDIP | 28-PDIP | 28-PDIP | 28-PDIP |
| Multiplexer Configuration | 16:1 | 16:1 | 16:1 | Dual 8-channel | 4:1 or dual 4:1 | 4:1 or dual 4:1 |
主要差異化特點
- Single 16:1 multiplexing arrangement (對比DG407DJ+)
- Defined channel-to-channel resistance matching (對比DG406DJ+)
- Low charge injection for analog switching (對比MAX396EPI)
- Single and dual low-voltage supply operation (對比MAX397CPI+)
設計說明
Route the 16 analog inputs and common analog output as compact, quiet traces, with the mux positioned close to the sensor or measurement source. Long traces can act as antenna-like pickup paths and add resistance that becomes significant beside the specified 100-ohms maximum on-resistance. Keep digital address lines away from the analog output, provide a continuous ground plane, and place supply-decoupling capacitors near the power pins.
Check source impedance and downstream capacitance before selecting the mux. The 100-ohms maximum on-resistance combines with source resistance and wiring capacitance to form an RC settling network, so a nominally correct switch may require extra acquisition time at high source impedances. For low-current or capacitor-based sensors, also evaluate the 5-pC maximum charge injection because each address transition can create a voltage transient.
Decouple the supply pins locally and select bypass values that suppress ripple on both the single-supply and dual-supply rails used by the design. The device accepts +2.7 V to +16 V or ±2.7 V to ±8 V, but the allowed signal range remains tied to the selected supply configuration. Verify address-logic levels, output limits, and injected switching transients against the exact operating mode in the manufacturer data sheet.
Do not substitute MAX397, DG406, or DG407 parts solely because they use a compatible 28-pin footprint. The MAX397 uses a dual 8-channel arrangement, while the DG406 and DG407 families have different channel configurations and truth tables. Confirm address mapping, selected-channel behavior, electrical limits, temperature grade, and package suffix before treating any listed alternative as a production drop-in replacement.
合規資訊
The manufacturer data sheet identifies ESD protection greater than 2,000 V per Method 3015.7. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses were not established from the cited product information.