MAX399CSE+ - Dual 4:1 Analog Multiplexer | Analog Devices
料号: MAX399CSE+ ✓ 量产中MAX399CSE+ 概述
An analog multiplexer is a semiconductor switching device that connects one common signal path to one of several input or output terminals. The MAX399 uses two independent 4:1 circuits within one package, allowing two analog channels to be selected simultaneously. In the broader component hierarchy, it belongs to analog switches, then interface ICs, then semiconductor devices used to manage signal routing in electronic systems. The MAX399CSE+ therefore sits between the signal source and the downstream measurement or processing circuit.
The principal performance features include on-resistance below 100 ohms and channel matching within 6 ohms. The on-resistance remains flat over the specified analog signal range, helping preserve signal amplitude relationships when different channels are selected. The low-voltage CMOS construction supports portable, battery-powered, and low-voltage data-acquisition systems where power efficiency and compact routing are important. The dual-circuit organization also reduces the number of packages needed when two independently controlled selections are required.
The MAX399 family comprises precision monolithic multiplexers intended for precision analog routing rather than high-speed digital multiplexing. Its two 4:1 sections allow one common node to select among four signal paths per section. This arrangement is useful where several sources share a common amplifier, converter, measurement channel, or system bus. Because the device is monolithic, its channel matching can remain tighter than would typically be expected from separately assembled discrete analog switches.
Typical uses include audio-signal routing, automated test equipment, battery-powered instruments, communication systems, guidance and control systems, heads-up displays, low-voltage data acquisition, military radios, private-branch exchanges, and sample-and-hold circuits. In an automated test system, the MAX399CSE+ can place multiple inputs in sequence on a shared measurement path. In instrumentation, it can route control or sensor signals without duplicating the front-end amplifier. In communication equipment, the dual structure can support two simultaneous routing paths within a compact board layout.
For PCB design, use the manufacturer's pin-description table when assigning traces and keep analog routing paths short and appropriately shielded from switching and digital circuitry. Confirm that each selected source stays within the device's specified analog signal range and supply limits. The low on-resistance is useful for many low-voltage measurements, but system accuracy still depends on source impedance, leakage, switch timing, and the bandwidth requirements of the downstream circuit.
This page combines manufacturer application guidance, package and architecture details, drop-in cross-reference options, and practical selection guidance. It is intended to help engineers identify whether the MAX399CSE+ matches a required routing architecture and how its 16-pin SOIC footprint compares with established multiplexer families.
直接替换替代料: MAX399CSE+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX399CSE+ (相同外形与封装尺寸) ——差异在于 Package, On-Resistance, Multiplexer Configuration, Signal Direction.
MAX398CSE+
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
DG408DY+
✅ 直接替换联系询价
查看数据手册 →DG409DY+
✅ 直接替换联系询价
查看数据手册 →DG508ADY+
✅ 直接替换📋 参考替代料(不在目录中)
DG509ADY+
✅ 直接替换📋 参考替代料(不在目录中)
MAX399CSE+ 规格参数
| Device Type | Precision CMOS analog multiplexer |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | Dual 4:1 |
| On-Resistance | <100 ohm |
| On-Resistance Matching Between Channels | <=6 ohm |
| Maximum On-Resistance Variation | 11 ohm maximum |
| Channel Count | 8 channels configured as two 4:1 circuits |
| 封装 | 16-pin SOIC |
| 安装类型 | Surface mount |
MAX399CSE+ 16-pin soic 引脚配置指南
MAX399CSE+(16-pin soic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX399CSE+.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX399CSE+ 适用于 6 应用s: Automated Test Equipment, Audio Signal Routing, Battery-Powered Instruments, Communication Systems, Guidance and Control Systems, Sample-and-Hold Circuits.
Automated Test Equipment
The MAX399CSE+ suits automated test equipment that must connect multiple analog test points to a shared measurement path. Its two 4:1 circuits can provide two independent selections within one 16-pin SOIC package, reducing routing complexity and component count. The less-than-100-ohm on-resistance and channel matching within 6 ohms help preserve relative signal amplitude across selections. During design, account for switching time and source impedance when defining measurement settling margins, and use the manufacturer's pin-description table to implement the select and enable controls correctly.
推荐
Audio Signal Routing
The MAX399CSE+ can route low-voltage audio signals among multiple sources in audio test and signal-conditioning equipment. Its two 4:1 sections allow independent routing of two related paths while maintaining a monolithic on-resistance match within 6 ohms between channels. This characteristic can help limit level changes when the system switches among sources. The design should still account for insertion resistance, source impedance, downstream amplifier loading, and the specified analog signal range to prevent avoidable attenuation or distortion.
推荐
Battery-Powered Instruments
The MAX399CSE+ is appropriate for battery-powered instruments requiring compact analog routing with low-voltage CMOS characteristics. Its 16-pin SOIC package combines two 4:1 switch sections, allowing one device to manage two selections instead of requiring separate multiplexers. On-resistance below 100 ohms and matching within 6 ohms support consistent signal transfer, although the complete power budget must include quiescent current, control-state current, and leakage. Check the manufacturer operating limits against the instrument's battery range and lowest valid signal level.
推荐
Communication Systems
The MAX399CSE+ can support analog signal selection in communication systems where multiple inputs feed a shared processing path. Two independent 4:1 sections provide flexible routing in a single 16-pin SOIC device, and the family is expressly associated with communication-system applications by Analog Devices. When choosing between mux families, compare insertion loss, off-state isolation, switching time, leakage, and supply requirements rather than using channel count alone. PCB traces connected to the selected analog nodes should remain short and be positioned away from high-energy switching nodes.
推荐
Guidance and Control Systems
The MAX399CSE+ is suitable for guidance and control systems that select several low-voltage analog command or feedback signals through a common interface. Its dual 4:1 organization allows two control paths to be multiplexed in one package, while on-resistance matching within 6 ohms helps maintain consistent control or measurement levels. Designers should verify settling behavior, allowable input levels, and control timing for the exact operating conditions. Use a defined ground and return strategy to prevent common-impedance effects from undermining the mux's channel-matching performance.
推荐
Sample-and-Hold Circuits
The MAX399CSE+ can be used in sample-and-hold systems to place one of several analog inputs onto a shared sampling path. The MAX399 family's two 4:1 sections support selection of more than one source, and its on-resistance below 100 ohms can reduce insertion loss when source impedances are appropriately controlled. Performance still depends on the sampling capacitor, acquisition time, switch leakage, and input capacitance. Confirm settling at the lowest signal frequency and highest source impedance, and account for charge injection or acquisition-error behavior specified for the operating conditions.
推荐
推荐产品汇总
工程参考数据: MAX399CSE+ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX398CSE+ | DG408DY+ | DG409DY+ | DG508ADY+ | DG509ADY+ |
|---|---|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Architecture | Dual 4:1 | 8:1 single-ended | 8:1 | 8:1 | 8:1 | 8:1 |
| Number of Independent Circuits | 2 circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Total Signal Paths | 8 paths | 8 paths | 8 paths | 8 paths | 8 paths | 8 paths |
| Manufacturer Pin Compatibility | MAX399 | Same MAX398/MAX399 family | Identified as pin compatible | Identified as pin compatible | Identified as pin compatible | Identified as pin compatible |
关键差异点
- Two independent 4:1 sections in one package (对比 MAX398CSE+)
- Manufacturer-supported industry-standard pin compatibility (对比 DG408DY+)
- Precision monolithic channel matching (对比 DG509ADY+)
- Compact dual-section routing (对比 DG508ADY+)
设计说明
Use the complete pin-description table in the manufacturer datasheet when assigning the 16-pin SOIC footprint. Keep the common analog terminals, selected inputs, control inputs, supply pins, and ground connection consistent with the intended circuit architecture. Because the MAX399CSE+ contains two 4:1 sections, trace both common nodes independently and verify that replacement-family control polarity and selection logic have been reviewed before populating an alternate device.
Treat the less-than-100-ohm on-resistance as part of the complete signal path rather than as an isolated specification. Calculate the total attenuation using the selected source impedance, switch on-resistance, and downstream input impedance. For precision measurements, also evaluate the stated matching within 6 ohms because a channel-to-channel resistance difference can create level error when source impedance is high. Use short analog traces and a quiet ground reference to minimize additional error.
Do not select a replacement solely because it uses a 16-pin SOIC package or because the family is described as pin compatible. The MAX399 uses two 4:1 circuits, while several established alternatives use an 8:1 arrangement. Confirm the common-node topology, selection truth table, enable behavior, supply limits, switching timing, leakage, and allowable analog range. Prototype the exact ordering code under worst-case source impedance, temperature, and supply conditions before releasing a replacement design.
Confirm the device's supply range, quiescent current, and control-state current against the complete datasheet before using the MAX399CSE+ in a battery-powered design. The low-voltage CMOS architecture is suited to portable equipment, but total power depends on supply voltage, enabled duration, leakage, and the resistance of the connected source network. Provide adequate local supply bypassing and maintain a low-impedance return path to reduce supply noise and common-mode effects at the analog nodes.
合规信息
The manufacturer product page identifies MAX399 as production, but the listed verification does not explicitly establish the required compliance declarations or automotive qualification. Review current manufacturer documentation for the exact ordering code before making a compliance claim.