MAX399CSE+ - Dual 4:1 Analog Multiplexer | Analog Devices
MPN: MAX399CSE+ ✓ פעילMAX399CSE+ סקירה
An analog multiplexer is a semiconductor switching device that connects one common signal path to one of several input or output terminals. The MAX399 uses two independent 4:1 circuits within one package, allowing two analog channels to be selected simultaneously. In the broader component hierarchy, it belongs to analog switches, then interface ICs, then semiconductor devices used to manage signal routing in electronic systems. The MAX399CSE+ therefore sits between the signal source and the downstream measurement or processing circuit.
The principal performance features include on-resistance below 100 ohms and channel matching within 6 ohms. The on-resistance remains flat over the specified analog signal range, helping preserve signal amplitude relationships when different channels are selected. The low-voltage CMOS construction supports portable, battery-powered, and low-voltage data-acquisition systems where power efficiency and compact routing are important. The dual-circuit organization also reduces the number of packages needed when two independently controlled selections are required.
The MAX399 family comprises precision monolithic multiplexers intended for precision analog routing rather than high-speed digital multiplexing. Its two 4:1 sections allow one common node to select among four signal paths per section. This arrangement is useful where several sources share a common amplifier, converter, measurement channel, or system bus. Because the device is monolithic, its channel matching can remain tighter than would typically be expected from separately assembled discrete analog switches.
Typical uses include audio-signal routing, automated test equipment, battery-powered instruments, communication systems, guidance and control systems, heads-up displays, low-voltage data acquisition, military radios, private-branch exchanges, and sample-and-hold circuits. In an automated test system, the MAX399CSE+ can place multiple inputs in sequence on a shared measurement path. In instrumentation, it can route control or sensor signals without duplicating the front-end amplifier. In communication equipment, the dual structure can support two simultaneous routing paths within a compact board layout.
For PCB design, use the manufacturer's pin-description table when assigning traces and keep analog routing paths short and appropriately shielded from switching and digital circuitry. Confirm that each selected source stays within the device's specified analog signal range and supply limits. The low on-resistance is useful for many low-voltage measurements, but system accuracy still depends on source impedance, leakage, switch timing, and the bandwidth requirements of the downstream circuit.
This page combines manufacturer application guidance, package and architecture details, drop-in cross-reference options, and practical selection guidance. It is intended to help engineers identify whether the MAX399CSE+ matches a required routing architecture and how its 16-pin SOIC footprint compares with established multiplexer families.
חלופות תחליף ישיר עבור MAX399CSE+ — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם MAX399CSE+ (אותו גורם צורה וטביעת רגל) — שונים ב Package, On-Resistance, Multiplexer Configuration, Signal Direction.
MAX398CSE+
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
DG408DY+
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DG409DY+
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←DG508ADY+
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
DG509ADY+
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
MAX399CSE+ מפרטים
| Device Type | Precision CMOS analog multiplexer |
| Number of Circuits | 2 circuits |
| Multiplexer Configuration | Dual 4:1 |
| On-Resistance | <100 ohm |
| On-Resistance Matching Between Channels | <=6 ohm |
| Maximum On-Resistance Variation | 11 ohm maximum |
| Channel Count | 8 channels configured as two 4:1 circuits |
| מארז | 16-pin SOIC |
| סוג הרכבה | Surface mount |
מדריך תצורת פינים של MAX399CSE+ 16-pin soic
תצורת פינים עבור MAX399CSE+ (מארזת 16-pin soic). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור MAX399CSE+.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
MAX399CSE+ מתאים עבור 6 יישוםs: Automated Test Equipment, Audio Signal Routing, Battery-Powered Instruments, Communication Systems, Guidance and Control Systems, Sample-and-Hold Circuits.
Automated Test Equipment
The MAX399CSE+ suits automated test equipment that must connect multiple analog test points to a shared measurement path. Its two 4:1 circuits can provide two independent selections within one 16-pin SOIC package, reducing routing complexity and component count. The less-than-100-ohm on-resistance and channel matching within 6 ohms help preserve relative signal amplitude across selections. During design, account for switching time and source impedance when defining measurement settling margins, and use the manufacturer's pin-description table to implement the select and enable controls correctly.
מומלץ
Audio Signal Routing
The MAX399CSE+ can route low-voltage audio signals among multiple sources in audio test and signal-conditioning equipment. Its two 4:1 sections allow independent routing of two related paths while maintaining a monolithic on-resistance match within 6 ohms between channels. This characteristic can help limit level changes when the system switches among sources. The design should still account for insertion resistance, source impedance, downstream amplifier loading, and the specified analog signal range to prevent avoidable attenuation or distortion.
מומלץ
Battery-Powered Instruments
The MAX399CSE+ is appropriate for battery-powered instruments requiring compact analog routing with low-voltage CMOS characteristics. Its 16-pin SOIC package combines two 4:1 switch sections, allowing one device to manage two selections instead of requiring separate multiplexers. On-resistance below 100 ohms and matching within 6 ohms support consistent signal transfer, although the complete power budget must include quiescent current, control-state current, and leakage. Check the manufacturer operating limits against the instrument's battery range and lowest valid signal level.
מומלץ
Communication Systems
The MAX399CSE+ can support analog signal selection in communication systems where multiple inputs feed a shared processing path. Two independent 4:1 sections provide flexible routing in a single 16-pin SOIC device, and the family is expressly associated with communication-system applications by Analog Devices. When choosing between mux families, compare insertion loss, off-state isolation, switching time, leakage, and supply requirements rather than using channel count alone. PCB traces connected to the selected analog nodes should remain short and be positioned away from high-energy switching nodes.
מומלץ
Guidance and Control Systems
The MAX399CSE+ is suitable for guidance and control systems that select several low-voltage analog command or feedback signals through a common interface. Its dual 4:1 organization allows two control paths to be multiplexed in one package, while on-resistance matching within 6 ohms helps maintain consistent control or measurement levels. Designers should verify settling behavior, allowable input levels, and control timing for the exact operating conditions. Use a defined ground and return strategy to prevent common-impedance effects from undermining the mux's channel-matching performance.
מומלץ
Sample-and-Hold Circuits
The MAX399CSE+ can be used in sample-and-hold systems to place one of several analog inputs onto a shared sampling path. The MAX399 family's two 4:1 sections support selection of more than one source, and its on-resistance below 100 ohms can reduce insertion loss when source impedances are appropriately controlled. Performance still depends on the sampling capacitor, acquisition time, switch leakage, and input capacitance. Confirm settling at the lowest signal frequency and highest source impedance, and account for charge injection or acquisition-error behavior specified for the operating conditions.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור MAX399CSE+ — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | MAX398CSE+ | DG408DY+ | DG409DY+ | DG508ADY+ | DG509ADY+ |
|---|---|---|---|---|---|---|
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Architecture | Dual 4:1 | 8:1 single-ended | 8:1 | 8:1 | 8:1 | 8:1 |
| Number of Independent Circuits | 2 circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Total Signal Paths | 8 paths | 8 paths | 8 paths | 8 paths | 8 paths | 8 paths |
| Manufacturer Pin Compatibility | MAX399 | Same MAX398/MAX399 family | Identified as pin compatible | Identified as pin compatible | Identified as pin compatible | Identified as pin compatible |
מבדילים עיקריים
- Two independent 4:1 sections in one package (לעומתMAX398CSE+)
- Manufacturer-supported industry-standard pin compatibility (לעומתDG408DY+)
- Precision monolithic channel matching (לעומתDG509ADY+)
- Compact dual-section routing (לעומתDG508ADY+)
הערות תכנון
Use the complete pin-description table in the manufacturer datasheet when assigning the 16-pin SOIC footprint. Keep the common analog terminals, selected inputs, control inputs, supply pins, and ground connection consistent with the intended circuit architecture. Because the MAX399CSE+ contains two 4:1 sections, trace both common nodes independently and verify that replacement-family control polarity and selection logic have been reviewed before populating an alternate device.
Treat the less-than-100-ohm on-resistance as part of the complete signal path rather than as an isolated specification. Calculate the total attenuation using the selected source impedance, switch on-resistance, and downstream input impedance. For precision measurements, also evaluate the stated matching within 6 ohms because a channel-to-channel resistance difference can create level error when source impedance is high. Use short analog traces and a quiet ground reference to minimize additional error.
Do not select a replacement solely because it uses a 16-pin SOIC package or because the family is described as pin compatible. The MAX399 uses two 4:1 circuits, while several established alternatives use an 8:1 arrangement. Confirm the common-node topology, selection truth table, enable behavior, supply limits, switching timing, leakage, and allowable analog range. Prototype the exact ordering code under worst-case source impedance, temperature, and supply conditions before releasing a replacement design.
Confirm the device's supply range, quiescent current, and control-state current against the complete datasheet before using the MAX399CSE+ in a battery-powered design. The low-voltage CMOS architecture is suited to portable equipment, but total power depends on supply voltage, enabled duration, leakage, and the resistance of the connected source network. Provide adequate local supply bypassing and maintain a low-impedance return path to reduce supply noise and common-mode effects at the analog nodes.
מידע על תאימות
The manufacturer product page identifies MAX399 as production, but the listed verification does not explicitly establish the required compliance declarations or automotive qualification. Review current manufacturer documentation for the exact ordering code before making a compliance claim.