MC34071PG - 44V Single Op Amp, 4.5MHz | onsemi
料号: MC34071PG ✓ 量产中MC34071PG 概述
An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify or buffer signals in electronic systems. The MC34071 belongs to the broader hierarchy of operational amplifiers, analog amplifiers, and signal-chain semiconductors. Its wide supply range allows it to operate from conventional 5 V and 12 V rails as well as higher industrial voltage systems, although the complete circuit must remain within the device's absolute maximum ratings.
Key characteristics include a 4.5 MHz gain-bandwidth product, 13 V/µs slew rate, single-ended input configuration, and a general-purpose amplifier design. The manufacturer describes the MC34071 series as using quality bipolar fabrication and innovative design concepts. The bipolar approach supports conventional op-amp behavior and is useful in applications requiring signal amplification, buffering, active filtering, and general analog control functions.
The device's fast settling performance and 13 V/µs slew rate make it more responsive than slow precision-oriented amplifiers. This is beneficial for instrumentation and feedback loops that need to follow changing input waveforms. Designers should still account for input and output voltage limits, common-mode range, output-current capability, supply decoupling, and stability when driving capacitive or nonlinear loads.
Typical uses include industrial process-control instrumentation, sensor signal conditioning, audio and communications support circuits, active filters, voltage followers, and general laboratory measurement equipment. Because the MC34071PG is a through-hole PDIP device, it is especially convenient for prototyping, educational systems, repair work, and applications where socketed or manually soldered assembly is acceptable.
For reliable operation, decouple the supply pins close to the device and provide stable reference and feedback paths. Avoid forcing the output beyond its rated output-voltage swing, and check the input common-mode range over the complete operating range. Use the manufacturer pin description and electrical characteristics tables when assigning PCB nets and designing around input offset, bias current, supply current, and output-drive limits.
This product page combines manufacturer specifications, package information, design guidance, drop-in alternatives, and a parameter-by-parameter comparison to support faster component selection and PCB-level planning for MC34071PG-based analog circuits.
直接替换替代料: MC34071PG ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MC34071PG (相同外形与封装尺寸) ——差异在于 Mounting Type, Package.
MC34071APG
✅ 直接替换📋 参考替代料(不在目录中)
MC34071P
✅ 直接替换联系询价
查看数据手册 →UA741CPE4
✅ 直接替换📋 参考替代料(不在目录中)
MC34071PG 最大额定值与电气特性
| Product Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Amplifier Type | General-purpose |
| Single-Supply Voltage Range | 3.0 V to 44 V |
| Gain-Bandwidth Product | 4.5 MHz |
| Slew Rate | 13 V/µs |
| Input Configuration | Single-ended |
| Process Technology | Bipolar |
| 封装 | 8-pin PDIP (0.300 in, 7.62 mm pitch) |
| Package Type | PDIP-8 |
| 安装类型 | Through-hole |
| Packaging | Tube |
| Temperature Grade | Commercial |
| Terminal Count | 8 terminals |
| AEC-Q100 Qualification | Not applicable |
MC34071PG pdip-8 引脚配置指南
MC34071PG(pdip-8 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: MC34071PG.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MC34071PG 适用于 6 应用s: Industrial Sensor Signal Conditioning, Active Audio Filter, Precision Test and Measurement Buffer, Communications Interface Buffer, Power Supply Feedback Control, Educational and Prototype Analog Circuit.
Industrial Sensor Signal Conditioning
The MC34071PG fits industrial sensor front ends that need a fast general-purpose amplifier stage between a transducer and a measurement or control circuit. Its 4.5 MHz gain-bandwidth product provides more bandwidth than a slow precision-only amplifier, while 13 V/µs slew rate helps the output follow rapidly changing sensor signals. The 3 V to 44 V single-supply range also supports a broad range of industrial rail conditions. Because the MC34071PG uses a bipolar input stage, the design should include offset-voltage, bias-current, and common-mode checks against the sensor output. Place power-bypass capacitors near the device, keep feedback traces short, and verify the sensor's full output range before choosing the gain and reference network.
推荐
Active Audio Filter
The MC34071PG is suitable for active filtering in audio and communications equipment where a conventional general-purpose op amp with moderate speed is sufficient. Its 4.5 MHz gain-bandwidth product and 13 V/µs slew rate provide ample response for many low- and mid-frequency audio stages, while the single 3 V to 44 V supply simplifies integration with varied rails. The bipolar input architecture supports familiar feedback and compensation methods, although the selected noise-gain topology must remain stable with the intended source impedance and load. Check output swing, output-current demand, and supply headroom at the lowest rail voltage. Short feedback loops and a clean, decoupled supply help limit distortion and unintended oscillation in an active audio filter.
推荐
Precision Test and Measurement Buffer
The MC34071PG can serve as a general-purpose buffer or gain stage in laboratory and test equipment where response speed matters more than ultimate precision. A gain-bandwidth product of 4.5 MHz and slew rate of 13 V/µs allow the amplifier to drive changing waveforms without the slow settling behavior expected from many low-offset devices. For instrumentation-grade measurement, however, the design engineer must still budget the amplifier's input offset, input bias current, and output errors against the required accuracy. The 3 V to 44 V operating range supports laboratory systems using several common supply voltages. Use short, guarded input paths, clean grounding, and stable reference components so the buffer does not degrade the accuracy of the source being measured.
推荐
Communications Interface Buffer
The MC34071PG is appropriate for communications equipment that requires a fast, single-ended buffer between a source and an active stage. Its 13 V/µs slew rate helps preserve signal transitions, and its 4.5 MHz gain-bandwidth product is suitable for many low-frequency control, monitor, and analog-interface paths. The wide 3 V to 44 V single-supply operation makes it useful in industrial communication systems with varied rail architectures. Designers should keep the amplifier stable with the source and load impedances, verify that the input common-mode range covers the full source swing, and provide local supply bypassing. When handling higher-speed or larger-swing signals, compare output-current demand and distortion against the completed circuit rather than relying on gain-bandwidth product alone.
推荐
Power Supply Feedback Control
The MC34071PG can be evaluated for error-amplifier or feedback functions in a regulated power-supply control loop where response speed and supply range are important. Its 4.5 MHz gain-bandwidth product and 13 V/µs slew rate allow relatively quick correction of moderate output disturbances, and the device accepts a 3 V to 44 V single supply for integration with higher-energy industrial rails. Its general-purpose bipolar construction makes it familiar in classic voltage-mode control architectures. The control-loop design must account for output saturation, common-mode limits, compensation, and the amplifier's interaction with switching-node noise. Use a dedicated voltage reference and carefully filtered feedback division. Confirm stability across the intended input, output, and load ranges before using the amplifier near a switching power stage.
推荐
Educational and Prototype Analog Circuit
The MC34071PG is practical for educational laboratories, breadboard prototypes, and repair platforms because it combines a familiar 8-pin PDIP package with a general-purpose 4.5 MHz gain-bandwidth product. The through-hole format makes the amplifier easy to insert and replace without fine-pitch rework equipment, while 13 V/µs slew rate allows demonstration of amplifier response, active filtering, and feedback behavior. The 3 V to 44 V operating range enables operation from common laboratory supplies as well as higher-voltage demonstrations when the instructor confirms the absolute maximum limits. Keep the lesson circuit within the input and output common-mode limits, use a stable bypass capacitor at the supply pin, and avoid connecting outputs together. For permanent production equipment, assess whether a surface-mount package would improve mechanical reliability.
推荐
推荐产品汇总
工程参考数据: MC34071PG ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MC34071APG | MC34071P | UA741CPE4 |
|---|---|---|---|---|
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Brand | onsemi | onsemi | onsemi | Texas Instruments |
| Amplifier Type | General-purpose single op amp | General-purpose MC34071 family variant | General-purpose MC34071 family variant | General-purpose operational amplifier |
| Number of Circuits | 1 | 1 | 1 | 1 |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole |
关键差异点
- Wide single-supply operating range (对比 UA741CPE4)
- Fast response for a general-purpose bipolar amplifier (对比 MC34071P)
- Closest same-family packaged alternative (对比 MC34071APG)
设计说明
Operate the MC34071PG only within its specified 3 V to 44 V single-supply range and verify the absolute maximum supply ratings before energizing the circuit. Place a ceramic bypass capacitor close to the positive supply terminal and connect the negative supply terminal to the ground plane with a short path. For dual-supply operation, calculate the total voltage across the device and confirm that input and output voltages remain inside their permitted common-mode and output-swing limits.
Do not assume that the 4.5 MHz gain-bandwidth product is the usable closed-loop bandwidth at every gain. Stability also depends on noise gain, source impedance, load capacitance, and the feedback components. Check the manufacturer stability guidance before driving capacitive loads, and add an isolation resistor when the output must drive a long cable, connector, or large capacitor.
Keep the input, feedback, and output paths compact and route them away from noisy switching nodes and high-current return paths. Use a continuous ground plane, maintain a common reference between the signal source and the amplifier, and decouple supply pins locally. For instrumentation circuits, guard or shield high-impedance input traces because the bipolar input stage can draw bias current and may couple leakage into nearby nodes.
合规信息
The MC34071PG is a commercial-grade general-purpose operational amplifier in an 8-pin PDIP package. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established from the available manufacturer and distributor records.