MCF5407FT220 - ColdFire V4 32-bit MPU 220MHz 208-FQFP | NXP
料号： MCF5407FT220 ⚠ 最后一次采购| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $34.2 | $342.00 |
| 100 | $28.9 | $2,890.00 |
| 250 | $26.5 | $6,625.00 |
| 500 | $24.1 | $12,050.00 |
MCF5407FT220 概述
A microprocessor (MPU) is an integrated circuit that contains a CPU core plus system peripherals and is typically deployed in applications requiring external memory. Within the ColdFire product hierarchy, the V4 architecture sits between the V3 (lower-cost) and V5 (higher-performance with MMU) families, and belongs to the broader MPU category of digital semiconductors. The ColdFire ISA is a simplified 68k-style variable-length instruction set, providing high code density and predictable execution for C-code embedded firmware.
Key features of the MCF5407FT220 include 220 MHz core frequency, ROMless operation requiring external boot ROM/Flash, on-chip SRAM, an integrated SDRAM/DDR memory controller, Ethernet MAC, PCI interface, multiple UARTs, I2C, and DMA channels. According to DigiKey's listing (DigiKey part number MCF5407FT220-ND), the part is specified for commercial temperature grade with a 208-FQFP (28x28) gull-wing package suitable for high-density PCB designs.
The ColdFire V4 core implements a Harvard-style architecture with separate instruction and data paths and an enhanced multiply-accumulate (EMAC) unit, supporting DSP-like operations. The 220 MHz core delivers approximately 260 MIPS of integer performance, suitable for protocol stacks, RTOS kernels, and modest signal-processing workloads.
Typical applications include industrial Ethernet nodes (EtherCAT, PROFINET slave), serial-protocol bridges (UART, SPI, I2C concentrators), motor-control and HMI controllers, point-of-sale (POS) terminals, networked sensors, and embedded Linux/RTOS gateway platforms. The integrated Ethernet MAC plus PCI bus makes the MCF5407 particularly suited for legacy industrial PC/104 form-factor boards.
When designing with the MCF5407FT220, allocate adequate 4-layer PCB real estate for the 28x28 mm FQFP package, ensure decoupling per reference manual, and validate boot configuration strap pins at reset. Note that this ColdFire V4 MPU requires external boot memory and is software-incompatible with Cortex-M MCUs.
This page synthesizes distributor pricing, drop-in alternative search results, and practical ColdFire V4 design considerations beyond what the manufacturer datasheet alone provides, helping engineers shorten the device-selection step.
直接替换替代料： MCF5407FT220 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MCF5407FT220 （相同外形与封装尺寸） ——差异在于 Mounting Type, PCI Interface, Program Memory Type.
快速对比工具——选择替代料号进行并排对比：
MCF5407FT162
✅ 直接替换📋 参考替代料（不在目录中）
MCF5407FT266
✅ 直接替换📋 参考替代料（不在目录中）
MCF5475VR266
✅ 直接替换✓ 有现货
$26.4 / 个
查看数据手册 →MCF5474VR166
✅ 直接替换📋 参考替代料（不在目录中）
MCF5407FT220 最大额定值与电气特性
| Core Architecture | ColdFire V4 (MCF540x family) |
| 数据总线宽度 | 32-bit |
| Maximum Core Clock | 220 MHz |
| Program Memory Type | ROMless (requires external boot memory) |
| Package Type | 208-FQFP (28x28 mm) |
| 安装类型 | Surface Mount (gull-wing leads) |
| Terminal Count | 208 |
| Package Code | FQFP |
| Temperature Grade | Commercial |
| Family Series | MCF540x |
| Ethernet MAC | Integrated (per family datasheet) |
| PCI Interface | Integrated (per family datasheet) |
| Memory Controller | SDRAM/DDR (per family datasheet) |
| RoHS 状态 | Compliant (lead-free) |
MCF5407FT220 fqfp 引脚配置指南
MCF5407FT220（fqfp 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： MCF5407FT220.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MCF5407FT220 适用于 6 应用s: Industrial Ethernet Node, Serial Protocol Bridge / Concentrator, POS Terminal Controller, Motor Control & HMI Controller, Embedded Linux Gateway, Networked Sensor Hub.
Industrial Ethernet Node
The MCF5407FT220 fits industrial Ethernet nodes because its integrated 10/100 Ethernet MAC plus PCI controller and 220 MHz ColdFire V4 core can sustain EtherCAT, PROFINET, and Modbus TCP protocol stacks. The integrated MAC eliminates an external Ethernet controller, reducing BOM cost on PC/104 or DIN-rail PLC form-factor boards. Placed as the main processor with an external PHY (e.g., BCM5241), 32 MB SDRAM, and 8 MB boot Flash, it manages deterministic cycle times below 1 ms. Unlike Cortex-M alternatives, the ColdFire ISA maintains 68k-style code density useful for legacy ported firmware in factory automation.
推荐
Serial Protocol Bridge / Concentrator
The MCF5407FT220 is well-suited as a serial bridge hub because it provides multiple UARTs, I2C, and SPI peripherals alongside a 220 MHz core capable of running multi-protocol RTOS tasks. In gateway applications it aggregates RS-232/485, I2C sensor buses, and SPI peripherals, then forwards data over Ethernet. The on-chip DMA channels offload serial buffer handling from the CPU, sustaining aggregate throughput over 1 Mbps. Unlike small Cortex-M0 bridges, this MPU supports uClinux, enabling full TCP/IP stack and TLS libraries for secure remote management.
推荐
POS Terminal Controller
The MCF5407FT220 suits point-of-sale terminal main-controller roles due to its PCI bus (for cash drawer and magnetic-stripe peripherals), Ethernet MAC (for payment gateway connectivity), and 220 MHz ColdFire V4 performance running uClinux. The PCI interface simplifies integration of pre-certified payment peripherals that expect a PCI host. Compared with low-end 8-bit MCUs, the ColdFire MPU provides deterministic interrupt latency plus enough RAM headroom for cash-register firmware and TLS libraries. The 208-FQFP package is reflow-compatible with standard SMT lines.
推荐
Motor Control & HMI Controller
The MCF5407FT220 can drive mid-complexity motor-control plus HMI tasks because its 220 MHz ColdFire V4 core executes PWM loops and renders HMI graphics concurrently. The integrated EMAC unit accelerates torque-loop calculations while dedicated timers drive three-phase PWM outputs. Used with an external LCD controller over PCI, the part supports 320x240 color TFT displays for operator panels. Unlike DSP-only controllers, it provides full Ethernet for Industry 4.0 connectivity. Estimated: at 220 MHz and typical 3.3V core voltage, the MPU draws ~1.5 W under full load.
推荐
Embedded Linux Gateway
The MCF5407FT220 is a practical ColdFire V4 platform for uClinux-based Ethernet gateways because it provides an external bus interface for SDRAM plus boot Flash, an integrated MAC, and PCI expansion. Running mClinux 2.6 with the ColdFire ABI, the device serves small-scale IoT aggregation, Modbus/TCP-to-cloud bridges, and edge-protocol converters. The 208-FQFP footprint is preserved across the MCF5407 family, enabling designers to swap speed grades or move to MCF547x without PCB rework. Unlike Cortex-A SoCs, no external DDR controller chip is required.
推荐
Networked Sensor Hub
The MCF5407FT220 fits networked sensor hubs because it integrates Ethernet MAC, multiple UARTs, I2C, and SPI peripherals needed for sensor fan-in, plus a 220 MHz ColdFire V4 core capable of running embedded web servers and JSON/MQTT clients. The PCI bus supports expansion cards such as 4-port serial concentrators or CAN interfaces. Unlike small Cortex-M0 hubs, the ColdFire MPU runs uClinux, supporting TLS and full TCP/IP stacks. The 208-FQFP package provides enough GPIO for keypad and indicator LED drivers in compact DIN-rail enclosures.
推荐
推荐产品汇总
工程参考数据： MCF5407FT220 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MCF5407FT162 | MCF5407FT266 | MCF5475VR266 | MCF5474VR166 |
|---|---|---|---|---|---|
| Package | 208-FQFP (28x28) | 208-FQFP (28x28) - same | 208-FQFP (28x28) - same | 208-FQFP (28x28) - same | 208-FQFP (28x28) - same |
| Brand | NXP Semiconductors | NXP Semiconductors - same brand | NXP Semiconductors - same brand | NXP Semiconductors - same brand | NXP Semiconductors - same brand |
| Core Clock | 220 MHz | 162 MHz | 266 MHz | 266 MHz | 166 MHz |
| Core Architecture | ColdFire V4 | ColdFire V4 | ColdFire V4 | ColdFire V4e | ColdFire V4e |
| Ethernet MAC | Yes (10/100) | Yes (10/100) | Yes (10/100) | Yes (Fast Ethernet + USB) | Yes (Fast Ethernet) |
| PCI Controller | Yes | Yes | Yes | Yes | Yes |
| Program Memory | ROMless | ROMless | ROMless | ROMless | ROMless |
| Temperature Grade | Commercial | Commercial | Commercial | Commercial | Commercial |
| Lifecycle Status | Last-time-buy | Last-time-buy | Last-time-buy | Active (limited) | Last-time-buy |
关键差异点
- Higher core clock than MCF5407FT162 （对比 MCF5407FT162)
- ColdFire V4 core with EMAC DSP extensions （对比 MCF5475VR266)
- Integrated Ethernet MAC and PCI controller （对比 MCF5407FT162)
- Drop-in compatibility across MCF540x family （对比 MCF5407FT266)
设计说明
Estimated: the 208-FQFP (28x28 mm) package with 0.5 mm pitch requires a 4-layer PCB with 0.4 mm via-in-pad or dog-bone fan-out. Allocate at least 1 square inch of unbroken ground plane directly beneath the IC to provide thermal dissipation and reference return paths. Use microvia-in-pad technology if manufacturing budget allows to minimize parasitic inductance on the high-speed external bus signals.
The MCF5407FT220 requires separate 3.3V I/O and 1.5V/2.5V core supplies (consult reference manual for exact rail voltages). Place 10 uF bulk plus 100 nF decoupling within 5 mm of each power pin pair. Estimated: at 220 MHz and full peripheral activity, total power consumption is approximately 1.5-2 W; use a switching regulator with at least 80% efficiency to manage thermal dissipation.
Do not assume the part is pin-compatible with newer i.MX RT or Cortex-M MPUs - the ColdFire ISA and bus interface are different. Always check Mode/Configuration strap pins at reset and verify the boot memory interface (8/16/32-bit) matches your Flash device. Mixing 3.3V and 5V peripherals requires bus transceivers because the MCF5407 I/O is 3.3V tolerant only.
Estimated: at ambient 70C and full 220 MHz load, junction temperature can reach 95C, near the commercial limit. For sealed enclosures without airflow, consider derating to the MCF5407FT162 (162 MHz) or adding a small clip-on heatsink to the exposed die region. Verify with the manufacturer thermal model before finalizing mechanical design.
合规信息
RoHS compliant lead-free package per NXP product data. Not AEC-Q100 qualified - commercial temperature grade only. Halogen-free status not stated in the verified data and should be confirmed with NXP.
