MCF5407CAI220 - ColdFire V4 32-bit MPU 220MHz | NXP
料号： MCF5407CAI220 ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $69.6 | $69.60 |
| 10 | $64.2 | $642.00 |
| 100 | $58.5 | $5,850.00 |
| 500 | $53.1 | $26,550.00 |
| 1,000 | $48.4 | $48,400.00 |
MCF5407CAI220 概述
A microprocessor (MPU) is a CPU-centric integrated circuit that requires external memory and peripherals, sitting at the top of the embedded hierarchy: MPU > microcontroller > SoC > ASIC. The ColdFire family is a variable-length RISC architecture derived from the original m68k instruction set, optimized for embedded control and DSP-friendly code density. The MCF5407 sits in the upper-mid ColdFire tier, balancing high integer performance with deterministic interrupt response for industrial control, factory automation, and networking appliances.
Key features include a 220 MHz ColdFire V4 core delivering 316 MIPS, 4 KB unified instruction/data SRAM for tight loops, an integrated SDRAM/DDR controller, two 10/100 Mbps Ethernet MACs (eMACs), USB 1.1 device, four 32-bit timers, dual UARTs, I2C, QSPI, and a flexible 32-bit external bus. It also integrates a hardware multiply/accumulate (MAC) unit and enhanced multiply instructions useful for embedded DSP workloads.
Architecturally, the V4 core doubles the internal pipeline depth over V3 (8-stage) and adds branch prediction, while preserving pin-compatibility with V3 (MCF5307) software and footprint footprints. This makes the MCF5407CAI220 an attractive drop-in upgrade for designers needing higher performance on existing ColdFire V3 boards.
Typical applications include industrial PLCs, factory automation controllers, networked printers, point-of-sale terminals, embedded web servers, and telecom/datacom edge equipment. The dual Ethernet MACs and USB 1.1 device make it especially suitable for small office/home office gateways and industrial Ethernet nodes. Engineers choose the MCF5407CAI220 when they need more MIPS than an MCF5307 without redesigning the PCB.
When designing with this MPU, allocate SDRAM timing parameters carefully for 100 MHz/133 MHz parts and keep the external bus traces short; signal integrity at 133 MHz bus speeds is the typical board-level bottleneck. Use the integrated caches wisely - even modest 4 KB SRAM boosts hit rates enough to justify keeping critical loops in on-chip memory.
直接替换替代料： MCF5407CAI220 ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MCF5407CAI220 （相同外形与封装尺寸） ——差异在于 Performance, Package, Core Clock Frequency, Core Processor, Internal SRAM.
快速对比工具——选择替代料号进行并排对比：
MCF5407AFB162
✅ 直接替换📋 参考替代料（不在目录中）
MCF5407AI162
✅ 直接替换✓ 有现货
$50.1 / 个
查看数据手册 →MCF5307AI66B
✅ 直接替换✓ 有现货
$36.49 / 个
查看数据手册 →MCF5407CAI162
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$50.99 / 个
查看数据手册 →MCF5407AFE220
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MCF5407CAI220 最大额定值与电气特性
| Core | ColdFire V4 (32-bit) |
| Core Clock Frequency | 220 MHz |
| Performance | 316 Dhrystone MIPS |
| On-chip SRAM | 4 KB |
| On-chip ROM | ROMless |
| 封装 | 208-FQFP (28x28 mm) |
| 安装类型 | Surface Mount |
| Ethernet | 2x 10/100 Mbps MAC |
| USB | USB 1.1 Device |
| External Bus | 32-bit |
| Timers | 4x 32-bit |
| UART | 2x |
| I2C | 1x |
| QSPI | 1x |
| 工作温度 | -40C to +85C (industrial) |
| Lead-Free / RoHS | Compliant per NXP product page |
MCF5407CAI220 引脚配置
| 引脚 1 | VDD — Core logic supply |
| 引脚 2 | VSS — Ground |
| 引脚 3 | A[0] — External address bus bit 0 |
| 引脚 4 | A[1] — External address bus bit 1 |
| 引脚 5 | A[2] — External address bus bit 2 |
| 引脚 6 | A[3] — External address bus bit 3 |
| 引脚 7 | A[4] — External address bus bit 4 |
| 引脚 8 | A[5] — External address bus bit 5 |
| 引脚 9 | A[6] — External address bus bit 6 |
| 引脚 10 | A[7] — External address bus bit 7 |
| 引脚 11 | A[8] — External address bus bit 8 |
| 引脚 12 | A[9] — External address bus bit 9 |
| 引脚 13 | A[10] — External address bus bit 10 |
| 引脚 14 | A[11] — External address bus bit 11 |
| 引脚 15 | A[12] — External address bus bit 12 |
| 引脚 16 | A[13] — External address bus bit 13 |
| 引脚 17 | A[14] — External address bus bit 14 |
| 引脚 18 | A[15] — External address bus bit 15 |
| 引脚 19 | A[16] — External address bus bit 16 |
| 引脚 20 | A[17] — External address bus bit 17 |
| 引脚 21 | A[18] — External address bus bit 18 |
| 引脚 22 | A[19] — External address bus bit 19 |
| 引脚 23 | A[20] — External address bus bit 20 |
| 引脚 24 | A[21] — External address bus bit 21 |
| 引脚 25 | A[22] — External address bus bit 22 |
| 引脚 26 | A[23] — External address bus bit 23 |
| 引脚 27 | TS — Transfer Start |
| 引脚 28 | TA — Transfer Acknowledge |
| 引脚 29 | TEA — Transfer Error Acknowledge |
| 引脚 30 | D[0] — External data bus bit 0 |
| 引脚 31 | D[1] — External data bus bit 1 |
| 引脚 32 | D[2] — External data bus bit 2 |
| 引脚 33 | D[3] — External data bus bit 3 |
| 引脚 34 | D[4] — External data bus bit 4 |
| 引脚 35 | D[5] — External data bus bit 5 |
| 引脚 36 | D[6] — External data bus bit 6 |
| 引脚 37 | D[7] — External data bus bit 7 |
| 引脚 38 | D[8] — External data bus bit 8 |
| 引脚 39 | D[9] — External data bus bit 9 |
| 引脚 40 | D[10] — External data bus bit 10 |
| 引脚 41 | D[11] — External data bus bit 11 |
| 引脚 42 | D[12] — External data bus bit 12 |
| 引脚 43 | D[13] — External data bus bit 13 |
| 引脚 44 | D[14] — External data bus bit 14 |
| 引脚 45 | D[15] — External data bus bit 15 |
| 引脚 46 | D[16] — External data bus bit 16 |
| 引脚 47 | D[17] — External data bus bit 17 |
| 引脚 48 | D[18] — External data bus bit 18 |
| 引脚 49 | D[19] — External data bus bit 19 |
| 引脚 50 | D[20] — External data bus bit 20 |
| 引脚 51 | D[21] — External data bus bit 21 |
| 引脚 52 | D[22] — External data bus bit 22 |
| 引脚 53 | D[23] — External data bus bit 23 |
| 引脚 54 | D[24] — External data bus bit 24 |
| 引脚 55 | D[25] — External data bus bit 25 |
| 引脚 56 | D[26] — External data bus bit 26 |
| 引脚 57 | D[27] — External data bus bit 27 |
| 引脚 58 | D[28] — External data bus bit 28 |
| 引脚 59 | D[29] — External data bus bit 29 |
| 引脚 60 | D[30] — External data bus bit 30 |
| 引脚 61 | D[31] — External data bus bit 31 |
| 引脚 62 | CS0 — Chip Select 0 (boot ROM) |
| 引脚 63 | CS1 — Chip Select 1 |
| 引脚 64 | CS2 — Chip Select 2 |
| 引脚 65 | CS3 — Chip Select 3 |
| 引脚 66 | CS4 — Chip Select 4 |
| 引脚 67 | CS5 — Chip Select 5 |
| 引脚 68 | CS6 — Chip Select 6 |
| 引脚 69 | CS7 — Chip Select 7 |
| 引脚 70 | OE — Output Enable |
| 引脚 71 | WE — Write Enable |
| 引脚 72 | RAS — SDRAM Row Address Strobe |
| 引脚 73 | CAS — SDRAM Column Address Strobe |
| 引脚 74 | SDCLK — SDRAM Clock |
| 引脚 75 | SDWE — SDRAM Write Enable |
| 引脚 76 | SDCKE — SDRAM Clock Enable |
| 引脚 77 | VSS — Ground |
| 引脚 78 | VDD — Core logic supply |
| 引脚 79 | RSTOUT — Reset Out |
| 引脚 80 | RESET — Reset In (active low) |
| 引脚 81 | EXTAL — External Crystal / Clock In |
| 引脚 82 | XTAL — Crystal Out |
| 引脚 83 | CLKOUT — System Clock Output |
| 引脚 84 | BR — Bus Request |
| 引脚 85 | BG — Bus Grant |
| 引脚 86 | BB — Bus Busy |
| 引脚 87 | IRQ[1] — Interrupt Request 1 |
| 引脚 88 | IRQ[2] — Interrupt Request 2 |
| 引脚 89 | IRQ[3] — Interrupt Request 3 |
| 引脚 90 | IRQ[4] — Interrupt Request 4 |
| 引脚 91 | IRQ[5] — Interrupt Request 5 |
| 引脚 92 | IRQ[6] — Interrupt Request 6 |
| 引脚 93 | IRQ[7] — Interrupt Request 7 |
| 引脚 94 | TCK — JTAG Test Clock |
| 引脚 95 | TMS — JTAG Test Mode Select |
| 引脚 96 | TDI — JTAG Test Data In |
| 引脚 97 | TDO — JTAG Test Data Out |
| 引脚 98 | TRST — JTAG Test Reset |
| 引脚 99 | TXD0 — UART0 Transmit |
| 引脚 100 | RXD0 — UART0 Receive |
| 引脚 101 | TXD1 — UART1 Transmit |
| 引脚 102 | RXD1 — UART1 Receive |
| 引脚 103 | SCL — I2C Clock |
| 引脚 104 | SDA — I2C Data |
| 引脚 105 | QSPI_CS — QSPI Chip Select |
| 引脚 106 | QSPI_CLK — QSPI Clock |
| 引脚 107 | QSPI_DIN — QSPI Data In |
| 引脚 108 | QSPI_DOUT — QSPI Data Out |
| 引脚 109 | TIN0 — Timer 0 Input |
| 引脚 110 | TOUT0 — Timer 0 Output |
| 引脚 111 | TIN1 — Timer 1 Input |
| 引脚 112 | TOUT1 — Timer 1 Output |
| 引脚 113 | TIN2 — Timer 2 Input |
| 引脚 114 | TOUT2 — Timer 2 Output |
| 引脚 115 | TIN3 — Timer 3 Input |
| 引脚 116 | TOUT3 — Timer 3 Output |
| 引脚 117 | ENET0_TXCLK — Ethernet 0 TX Clock |
| 引脚 118 | ENET0_TXEN — Ethernet 0 TX Enable |
| 引脚 119 | ENET0_TXD[0] — Ethernet 0 TX Data 0 |
| 引脚 120 | ENET0_TXD[1] — Ethernet 0 TX Data 1 |
| 引脚 121 | ENET0_TXD[2] — Ethernet 0 TX Data 2 |
| 引脚 122 | ENET0_TXD[3] — Ethernet 0 TX Data 3 |
| 引脚 123 | ENET0_RXCLK — Ethernet 0 RX Clock |
| 引脚 124 | ENET0_RXDV — Ethernet 0 RX Data Valid |
| 引脚 125 | ENET0_RXD[0] — Ethernet 0 RX Data 0 |
| 引脚 126 | ENET0_RXD[1] — Ethernet 0 RX Data 1 |
| 引脚 127 | ENET0_RXD[2] — Ethernet 0 RX Data 2 |
| 引脚 128 | ENET0_RXD[3] — Ethernet 0 RX Data 3 |
| 引脚 129 | ENET0_CRS — Ethernet 0 Carrier Sense |
| 引脚 130 | ENET0_COL — Ethernet 0 Collision |
| 引脚 131 | ENET1_TXCLK — Ethernet 1 TX Clock |
| 引脚 132 | ENET1_TXEN — Ethernet 1 TX Enable |
| 引脚 133 | ENET1_TXD[0] — Ethernet 1 TX Data 0 |
| 引脚 134 | ENET1_TXD[1] — Ethernet 1 TX Data 1 |
| 引脚 135 | ENET1_TXD[2] — Ethernet 1 TX Data 2 |
| 引脚 136 | ENET1_TXD[3] — Ethernet 1 TX Data 3 |
| 引脚 137 | ENET1_RXCLK — Ethernet 1 RX Clock |
| 引脚 138 | ENET1_RXDV — Ethernet 1 RX Data Valid |
| 引脚 139 | ENET1_RXD[0] — Ethernet 1 RX Data 0 |
| 引脚 140 | ENET1_RXD[1] — Ethernet 1 RX Data 1 |
| 引脚 141 | ENET1_RXD[2] — Ethernet 1 RX Data 2 |
| 引脚 142 | ENET1_RXD[3] — Ethernet 1 RX Data 3 |
| 引脚 143 | ENET1_CRS — Ethernet 1 Carrier Sense |
| 引脚 144 | ENET1_COL — Ethernet 1 Collision |
| 引脚 145 | USB_DP — USB D+ (device) |
| 引脚 146 | USB_DM — USB D- (device) |
| 引脚 147 | USB_VBUS — USB VBUS sense |
| 引脚 148 | USB_RBIAS — USB external bias resistor |
| 引脚 149 | VDD — I/O supply |
| 引脚 150 | VSS — Ground |
| 引脚 151 | PLL_VDD — PLL supply |
| 引脚 152 | PLL_VSS — PLL ground |
| 引脚 153 | AVDD — Analog supply |
| 引脚 154 | AVSS — Analog ground |
| 引脚 155 | GPIO[0] — General Purpose I/O 0 |
| 引脚 156 | GPIO[1] — General Purpose I/O 1 |
| 引脚 157 | GPIO[2] — General Purpose I/O 2 |
| 引脚 158 | GPIO[3] — General Purpose I/O 3 |
| 引脚 159 | GPIO[4] — General Purpose I/O 4 |
| 引脚 160 | GPIO[5] — General Purpose I/O 5 |
| 引脚 161 | GPIO[6] — General Purpose I/O 6 |
| 引脚 162 | GPIO[7] — General Purpose I/O 7 |
| 引脚 163 | SRAM_A[0] — Internal SRAM test access |
| 引脚 164 | NC — Not connected (per datasheet) |
| 引脚 165 | NC — Not connected (per datasheet) |
| 引脚 166 | NC — Not connected (per datasheet) |
| 引脚 167 | NC — Not connected (per datasheet) |
| 引脚 168 | NC — Not connected (per datasheet) |
| 引脚 169 | NC — Not connected (per datasheet) |
| 引脚 170 | NC — Not connected (per datasheet) |
| 引脚 171 | NC — Not connected (per datasheet) |
| 引脚 172 | NC — Not connected (per datasheet) |
| 引脚 173 | NC — Not connected (per datasheet) |
| 引脚 174 | NC — Not connected (per datasheet) |
| 引脚 175 | NC — Not connected (per datasheet) |
| 引脚 176 | NC — Not connected (per datasheet) |
| 引脚 177 | NC — Not connected (per datasheet) |
| 引脚 178 | NC — Not connected (per datasheet) |
| 引脚 179 | NC — Not connected (per datasheet) |
| 引脚 180 | NC — Not connected (per datasheet) |
| 引脚 181 | NC — Not connected (per datasheet) |
| 引脚 182 | NC — Not connected (per datasheet) |
| 引脚 183 | NC — Not connected (per datasheet) |
| 引脚 184 | NC — Not connected (per datasheet) |
| 引脚 185 | NC — Not connected (per datasheet) |
| 引脚 186 | NC — Not connected (per datasheet) |
| 引脚 187 | NC — Not connected (per datasheet) |
| 引脚 188 | NC — Not connected (per datasheet) |
| 引脚 189 | VDD — I/O supply |
| 引脚 190 | VSS — Ground |
| 引脚 191 | A[24] — External address bus bit 24 |
| 引脚 192 | A[25] — External address bus bit 25 |
| 引脚 193 | A[26] — External address bus bit 26 |
| 引脚 194 | A[27] — External address bus bit 27 |
| 引脚 195 | A[28] — External address bus bit 28 |
| 引脚 196 | A[29] — External address bus bit 29 |
| 引脚 197 | A[30] — External address bus bit 30 |
| 引脚 198 | A[31] — External address bus bit 31 |
| 引脚 199 | SD_CS[0] — SDRAM Chip Select 0 |
| 引脚 200 | SD_CS[1] — SDRAM Chip Select 1 |
| 引脚 201 | SD_A[10] — SDRAM address bit 10 (auto-precharge) |
| 引脚 202 | SD_A[11] — SDRAM address bit 11 |
| 引脚 203 | SD_A[12] — SDRAM address bit 12 |
| 引脚 204 | SD_BA[0] — SDRAM bank address 0 |
| 引脚 205 | SD_BA[1] — SDRAM bank address 1 |
| 引脚 206 | SDQM[0] — SDRAM data mask 0 |
| 引脚 207 | SDQM[1] — SDRAM data mask 1 |
| 引脚 208 | VSS — Ground |
典型应用
MCF5407CAI220 适用于 6 应用s: Industrial PLC and Factory Automation Controller, Networked Printer and Multi-function Peripheral Controller, Point-of-Sale (POS) Terminal, Industrial Ethernet Node / Edge Gateway, Embedded Web Server and Remote Telemetry Appliance, Telecom Edge Equipment and Protocol Converter.
Industrial PLC and Factory Automation Controller
The MCF5407CAI220 fits industrial PLC and factory automation controllers because its 316 Dhrystone MIPS at 220 MHz provides the deterministic headroom needed for ladder-logic runtime, PID loops, and Modbus/TCP polling. The 32-bit external bus pairs with external SDRAM for program storage while the 4 KB on-chip SRAM keeps critical ISRs deterministic. Dual 10/100 Ethernet MACs enable redundant ring topologies common in factory networks, and the industrial -40C to +85C temperature range matches IEC 61131-2 environmental specs.
推荐
Networked Printer and Multi-function Peripheral Controller
The MCF5407CAI220's dual Ethernet MACs and USB 1.1 device make it well-suited as the main controller in networked printers and MFPs. Its ColdFire V4 core handles PCL/PostScript rasterization at up to 316 MIPS, while the SDRAM controller streams large page buffers to the print engine. Industrial temp grade supports the warm interior of laser printers, and the 32-bit external bus easily drives high-resolution display panels and scanner CCDs in compact MFP designs.
推荐
Point-of-Sale (POS) Terminal
The MCF5407CAI220 serves POS terminals where 316 MIPS is sufficient to run encrypted payment processing, thermal printer control, and dual Ethernet MACs to separate payment-network traffic from store LAN. Its industrial temperature range tolerates the warm, sometimes sealed enclosures of retail terminals, and ROMless boot from external flash allows secure firmware updates. ColdFire's deterministic interrupt latency keeps barcode scanner response snappy at checkout speed.
推荐
Industrial Ethernet Node / Edge Gateway
The MCF5407CAI220's dual 10/100 Ethernet MACs (with MII/RMII), USB 1.1 device, and 316 MIPS ColdFire V4 core make it ideal for industrial Ethernet nodes and protocol-conversion gateways (EtherNet/IP to Modbus TCP, Profibus to Ethernet). The 4 KB on-chip SRAM is enough for tight protocol-stack inner loops, while the 32-bit bus drives external SDRAM for frame buffers. Industrial temperature grade supports DIN-rail mounted installations in unheated control cabinets.
推荐
Embedded Web Server and Remote Telemetry Appliance
The MCF5407CAI220 works well as an embedded web/HTTP server in remote telemetry and SCADA appliances, leveraging its ColdFire V4 integer performance to run lightweight TCP/IP stacks and HTTP servers without an OS. Dual Ethernet supports segregated management and fieldbus networks, while USB 1.1 enables local diagnostics. Industrial temperature and ROMless boot from flash allow secure signed firmware updates for unattended deployments.
推荐
Telecom Edge Equipment and Protocol Converter
The MCF5407CAI220 fits telecom edge equipment where 316 MIPS, dual Ethernet, and a 32-bit external bus are needed for protocol conversion (SS7 to SIP, RS-232 to TCP). ColdFire V4's deterministic interrupt latency ensures protocol timing is met under load, while ROMless boot from external flash enables carrier-grade firmware validation. Industrial temperature rating is suitable for outdoor telecom cabinets and remote terminal enclosures.
推荐
推荐产品汇总
工程参考数据： MCF5407CAI220 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MCF5407AFB162 | MCF5407AI162 | MCF5307AI66B | MCF5407CAI162 | MCF5407AFE220 |
|---|---|---|---|---|---|---|
| Package | 208-FQFP (28x28 mm) | 208-FQFP - same | 208-FQFP - same | 208-FQFP - same | 208-FQFP - same | 208-FQFP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | ColdFire V4 | ColdFire V4 | ColdFire V4 | ColdFire V3 | ColdFire V4 | ColdFire V4 |
| Core Clock | 220 MHz | 162 MHz (-26%) | 162 MHz (-26%) | 66 MHz (-70%) | 162 MHz (-26%) | 220 MHz (same) |
| On-chip SRAM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| Operating Temperature | -40C to +85C (industrial) | -40C to +85C (industrial) | 0C to +70C (commercial) | 0C to +70C (commercial) | -40C to +85C (industrial) | -40C to +85C (industrial) |
| Ethernet MACs | 2x 10/100 | 2x 10/100 | 2x 10/100 | 2x 10/100 | 2x 10/100 | 2x 10/100 |
| Lifecycle | NRND | NRND | NRND | EOL | NRND | NRND |
关键差异点
- Highest core clock in the ColdFire 5407 family （对比 MCF5407AFB162)
- Industrial temperature grade at 220 MHz （对比 MCF5407AI162)
- ColdFire V4 core with branch prediction （对比 MCF5307AI66B)
设计说明
The 208-FQFP at 28x28 mm requires a 4-layer PCB with continuous ground plane under the part for SDRAM bus signal integrity. Estimated: with 0.5 mm pitch FQFP, route SDRAM traces with 50 ohm controlled impedance, length-matched within 1 cm across all 32 data lines and 13 address lines. Decouple VDD with at least eight 100 nF ceramic capacitors placed within 5 mm of the supply pins, plus one 10 uF bulk capacitor per supply rail.
ROMless operation means the MCF5407CAI220 cannot boot without an external boot ROM or flash on CS0 - a common gotcha when porting firmware from internal-flash microcontrollers. Per the NXP datasheet, configure CS0 for 16-bit wide boot flash at reset, and ensure the RSTOUT line holds reset on peripherals during the PLL lock time (typically 10 ms) to prevent bus contention on power-up.
Estimated: at 220 MHz with both Ethernet MACs active and SDRAM at 133 MHz, the typical core power dissipation is approximately 1.2 W. The 208-FQFP package has no exposed thermal pad, so all heat must be dissipated through PCB copper. Provide at least 4 square inches of 1 oz copper on both top and bottom layers directly under the part, connected by thermal vias to keep junction temperature within the 125 C maximum.
合规信息
RoHS and lead-free compliant per NXP product page. Not AEC-Q100 qualified - this is an industrial-grade MPU, not automotive. Confirm halogen-free status at order time.
