Microchip Technology

MCP6042-I/MS - Dual 14 kHz Low-Power CMOS Op Amp

料号: MCP6042-I/MS ✓ 量产中
Less than 3 mV Vdss 600 nA per amplifier Id 8-pin MSOP Package
最小起订量: 1 |

MCP6042-I/MS 概述

The Microchip Technology MCP6042-I/MS is a dual, general-purpose operational amplifier with a 14 kHz gain-bandwidth product, 600 nA typical operating current, and less than 3 mV offset voltage, supplied in an 8-pin MSOP package. It combines low-power CMOS operation with rail-to-rail input and output capability, making it suitable for portable instrumentation, sensor interfaces, battery-powered systems, and low-voltage signal-conditioning circuits.

An operational amplifier is an analog amplifier IC that uses high open-loop gain to amplify small input-voltage differences. The MCP6042 belongs to the operational-amplifier hierarchy within amplifier ICs and analog signal-chain processing. Its rail-to-rail input stage accepts signals across most of the supply range, while the rail-to-rail output stage can swing close to the positive and negative supply rails, improving usable dynamic range in low-voltage systems.

Key features include two amplifier channels, a 14 kHz gain-bandwidth product, a 3 V/µs slew rate, 1 pA typical input bias current, and 600 nA typical operating current per amplifier. The 1 pA bias current and low supply current are especially useful for high-impedance sensors, while the 1.4 V minimum operating voltage supports energy-limited and single-cell power systems. Offset voltage below 3 mV helps reduce output error in precision DC applications.

The MCP6042 uses Microchip's advanced CMOS technology to provide low bias current, high open-loop gain, and a rail-to-rail output swing. These characteristics make it more appropriate for portable measurement and sensor-conditioning applications than for high-bandwidth signal processing. Its 14 kHz gain-bandwidth product provides useful bandwidth for low-frequency control loops, filtering, buffering, and general-purpose analog amplification.

Typical uses include battery-powered sensor interfaces, portable medical instruments, industrial transmitters, low-voltage data acquisition, and low-frequency active filters. In these applications, the amplifier may follow a bridge sensor, photodiode, or low-current transducer. The dual configuration can process two related channels, such as a differential sensor input and a reference signal, without requiring two separate packages.

Design with the supply range and output-swing limits in mind, and use the manufacturer's pin-description table when assigning PCB tracks. Decoupling capacitors should be placed close to the supply pins, and sensitive high-impedance inputs should be guarded against leakage and contamination. The 8-pin MSOP footprint also allows a compact implementation, although adequate copper and solder mask clearance remain necessary for assembly.

This page consolidates the manufacturer's core electrical characteristics, verified commercial availability, package details, and practical design considerations into a concise engineering reference. It also distinguishes the same-family MSOP replacement candidates from alternatives that require a different footprint, helping designers evaluate PCB reuse without overlooking thermal, noise, or signal-range requirements.

直接替换替代料: MCP6042-I/MS ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MCP6042-I/MS (相同外形与封装尺寸) ——差异在于 Amplifier Type, Input Common-Mode Range, Input Offset Voltage, Number of Channels, Output Swing.

Microchip Technology
Amplifier Type: Single general-purpose operational amplifier
Input Common-Mode Range: Rail-to-rail
Input Offset Voltage: <3 mV

MCP6042T-E/MS

✅ 直接替换
📦 8-pin MSOP
Same MCP6042 family and 8-pin MSOP footprint; the E ordering code selects the extended-temperature grade, with no change to the stated 14 kHz gain-bandwidth product or 600 nA operating current.

📋 参考替代料(不在目录中)

MCP6042-I/MS 最大额定值与电气特性

Amplifier Type General-purpose operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 14 kHz
Slew Rate 3 V/µs
Typical Operating Current 600 nA per amplifier
Input Bias Current 1 pA typical
Input Offset Voltage Less than 3 mV
Supply Voltage Range 1.4 V to 5.5 V
Output Current 30 mA
Input Common-Mode Range Rail-to-rail input
Output Swing Rail-to-rail output
Process Technology Advanced CMOS
Open-Loop Gain High open-loop gain
封装 8-pin MSOP
安装类型 Surface mount

MCP6042-I/MS 8-pin msop 引脚配置指南

MCP6042-I/MS(8-pin msop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

MCP6042-I/MS 的 8-pin msop 封装引脚图

暂无详细引脚数据: MCP6042-I/MS.

请参阅 数据手册 以查看完整引脚配置。

典型应用

MCP6042-I/MS 适用于 6 应用s: Battery-Powered Sensor Interface, Portable Medical Signal Conditioning, Low-Voltage Data Acquisition, Industrial Transmitter Signal Path, Photodiode and Optical Signal Interface, Portable Instrumentation Buffering.

🧩

Battery-Powered Sensor Interface

The MCP6042-I/MS fits low-power sensor front ends because its 600 nA typical operating current reduces consumption while its 1 pA typical input bias current limits loading on high-impedance sources. Place one channel at the input of a resistive or bridge sensor and use the second channel for buffering a reference or diagnostic signal. Operation from 1.4 V to 5.5 V supports compact battery-powered designs, while rail-to-rail input and output behavior preserves signal range. Keep the input traces short, use guarding on very high-impedance nodes, and verify leakage from the PCB and connectors.

💊

Portable Medical Signal Conditioning

The MCP6042-I/MS is suitable for portable medical signal-conditioning circuits that need low noise-related operating current and high input impedance. Its 1 pA typical input bias current reduces errors when amplifying high-source-impedance biomedical sensors, while the 3 V/µs slew rate supports low-frequency waveforms with limited large-signal distortion. The dual amplifier can process a differential input and provide an intermediate buffer without using two packages. Rail-to-rail operation is valuable in compact systems, although clinical designs must also evaluate noise, accuracy, isolation, and applicable medical requirements independently.

📡

Low-Voltage Data Acquisition

The MCP6042-I/MS can condition low-level signals in compact data-acquisition systems operating from 1.4 V to 5.5 V. Its 14 kHz gain-bandwidth product is appropriate for slowly varying process, environmental, or instrumentation signals rather than wideband waveforms. Two channels can handle complementary sensor outputs or implement active filtering and gain stages. The 600 nA operating current is valuable in field-powered equipment, and the rail-to-rail output provides useful signal swing near low supply limits. Designers should include gain-error, offset, settling-time, and output-swing calculations for their selected closed-loop configuration.

🏭

Industrial Transmitter Signal Path

The MCP6042-I/MS is appropriate for low-frequency transmitter and receiver signal paths that prioritize low power, high input impedance, and compact implementation. The 1 pA typical bias current is useful with resistive or transducer inputs, while the 14 kHz gain-bandwidth product supports slow process-variable signals. Its rail-to-rail input and output operation helps maximize available range in 3.3 V or 5 V industrial electronics. Choose the temperature grade that covers the expected enclosure ambient and verify electromagnetic, surge, isolation, and calibration requirements at the system level rather than treating the op amp as the sole protection element.

📷

Photodiode and Optical Signal Interface

The MCP6042-I/MS can serve as a low-frequency transimpedance or voltage-gain stage in optical sensing systems. Its 1 pA typical input bias current is favorable when handling weak photodiode currents, and its low 600 nA operating current helps conserve power in compact optical modules. The 3 V/µs slew rate is more than adequate for many slow light-measurement channels. The practical design limit will often be photodiode capacitance, feedback-network stability, and input-node leakage rather than nominal gain-bandwidth product; use the manufacturer guidance to evaluate compensation and construct a guard ring around the sensitive input.

🖥️

Portable Instrumentation Buffering

The MCP6042-I/MS is useful for buffering sensor outputs in portable test and measurement instruments where every microamp of supply current can affect battery life. The dual configuration supports two buffered inputs, a differential stage, or a gain-plus-buffer arrangement in one MSOP package. A 14 kHz gain-bandwidth product suits meters, loggers, and low-frequency measurement channels, while rail-to-rail output improves headroom at 1.8 V, 3.3 V, or 5 V. Confirm the required accuracy and settling behavior with the selected feedback network, and use separate precision references or converters when the measurement specification cannot be met by the amplifier alone.

推荐产品汇总

MCP6042 Dual low-power operational-amplifier family 用于: Battery-Powered Sensor Interface, Portable Medical Signal Conditioning, Low-Voltage Data Acquisition, Industrial Transmitter Signal Path, Photodiode and Optical Signal Interface, Portable Instrumentation Buffering MCP6041 Related single-channel family member 用于: Battery-Powered Sensor Interface, Photodiode and Optical Signal Interface MCP6043 Related dual operational-amplifier family member 用于: Battery-Powered Sensor Interface, Low-Voltage Data Acquisition, Portable Instrumentation Buffering MCP6044 Related operational-amplifier family member 用于: Portable Medical Signal Conditioning, Low-Voltage Data Acquisition, Portable Instrumentation Buffering MCP6042T-E/MS Same-family option for extended-temperature assessment 用于: Industrial Transmitter Signal Path
What are the key specifications of MCP6042-I/MS that engineers should know?
The MCP6042-I/MS is a dual CMOS operational amplifier with a 14 kHz gain-bandwidth product, 3 V/µs slew rate, 600 nA typical operating current, and less than 3 mV input offset voltage. According to the Microchip MCP6042 product page, it supports rail-to-rail input and output operation from a 1.4 V to 5.5 V supply and is packaged in an 8-pin MSOP. Its 1 pA typical input bias current makes it suitable for high-impedance sensor interfaces and other leakage-sensitive analog circuits.
What is the supply voltage range of the MCP6042-I/MS?
The MCP6042-I/MS operates from 1.4 V to 5.5 V, allowing operation from low-energy sensor rails and conventional single-cell or regulated low-voltage supplies. According to Microchip's MCP6042 product page, its rail-to-rail input and output characteristics help maximize signal range at these low supply voltages. The available output swing is not completely independent of load current, so designers should check the load-current limits and output-voltage plots in the manufacturer documentation before defining exact logic or sensor-interface limits.
Why is the MCP6042-I/MS suitable for battery-powered sensor circuits?
The MCP6042-I/MS combines 600 nA typical operating current with a 1 pA typical input bias current, reducing both supply load and error caused by source leakage. According to Microchip's MCP6042 product page, the device also supports operation down to 1.4 V and provides rail-to-rail input and output behavior. These characteristics suit battery-powered pH, optical, environmental, and wearable sensor front ends where current consumption and input impedance strongly influence the usable measurement range.
Can MCP6042-I/MS be used with high-impedance sensors?
Yes, the MCP6042-I/MS is appropriate for many high-impedance sensor front ends because its typical input bias current is 1 pA. According to the Microchip MCP6042 product page, the low bias current minimizes the voltage error produced when flowing through a high-value sensor resistor. Practical results also depend on board cleanliness, protective leakage, resistor selection, and connector insulation, because board contamination can dominate the op amp's specified bias current.
What is the gain-bandwidth product and slew rate of MCP6042-I/MS?
The MCP6042-I/MS has a 14 kHz gain-bandwidth product and a 3 V/µs slew rate. According to the Microchip MCP6042 product page and its listed technical characteristics, these figures position it as a low-power, low-frequency amplifier rather than a high-speed signal-processing device. A 14 kHz unity-gain bandwidth is appropriate for slow sensor signals, active filters, buffers, and control loops, while the 3 V/µs slew rate helps limit large-signal output distortion.
Where can I download the MCP6042 datasheet PDF?
The official MCP6042 datasheet and product documentation can be accessed through Microchip's MCP6042 product page at https://www.microchip.com/en-us/product/MCP6042. The device is also listed on Datasheets.com, but the manufacturer page is the preferred starting point for the latest datasheet, package drawings, ordering information, and electrical characteristics. Use the pin-description table and electrical test conditions from the manufacturer document when assigning PCB connections or calculating design margins.
Where can I find the MCP6042 pinout?
Use the pin-description table in the Microchip MCP6042 manufacturer documentation to locate the MCP6042 pinout for the 8-pin MSOP package. The device contains two operational amplifiers, so the drawing identifies the power pins, two noninverting inputs, two inverting inputs, and two outputs. Because a complete verified pin map was not included in the product-page summary, use the manufacturer package drawing for final PCB routing rather than relying on a secondary diagram.
What can replace MCP6042-I/MS?
The MCP6042T-E/MS is a same-family Microchip option in the 8-pin MSOP package and is the closest identified drop-in candidate for MCP6042-I/MS. The distinction is temperature grade rather than circuit topology, so existing MSOP routing can be retained after checking the operating-temperature requirements. Cross-reference searches identify only limited compatible alternatives, and several familiar low-power amplifiers differ substantially in gain-bandwidth product, input bias current, or electrical limits; those devices should not be treated as automatically interchangeable.
Is MCP6042-I/MS the same as MCP6042T-I/MS?
MCP6042-I/MS and MCP6042T-I/MS identify the same MCP6042 dual operational-amplifier family in an 8-pin MSOP configuration, with the ordering suffix also indicating the manufacturer's shipment format. The listed technical characteristics remain those of the MCP6042 family. When replacing a purchased component, confirm the full manufacturer part number, packing method, temperature grade, and reel orientation rather than treating abbreviated ordering codes as separate amplifier designs.
Is MCP6042-I/MS suitable for low-frequency active filters?
Yes, the MCP6042-I/MS is suitable for many low-frequency active-filter stages because it offers a 14 kHz gain-bandwidth product, 3 V/µs slew rate, and rail-to-rail output capability. According to Microchip's MCP6042 product page, its low 600 nA operating current also supports battery-powered filter circuits. Component selection should account for noise gain, closed-loop bandwidth, capacitive loading, and output-swing headroom at the lowest supply voltage.
When should I choose MCP6042-I/MS over MCP6042T-E/MS?
Choose MCP6042-I/MS when the design operates within its specified industrial temperature range and the lower-temperature-grade option is sufficient. Choose MCP6042T-E/MS when the circuit must operate across a wider temperature range while retaining the same MCP6042 family, 8-pin MSOP footprint, and electrical topology. Check the exact temperature ratings and production requirements in the manufacturer documentation before finalizing the ordering code, especially for industrial equipment with elevated enclosure temperatures.
What is the best STMicroelectronics equivalent for MCP6042-I/MS?
Cross-reference information identifies an STMicroelectronics-compatible alternative for the MCP6042, but it does not provide the exact manufacturer part number in the accessible result. A valid drop-in decision requires confirmation of the 8-pin MSOP footprint, pin assignments, common-mode range, output swing, gain-bandwidth product, bias current, and supply limits. Until those details are verified, use Microchip's MCP6042 family rather than assuming an unspecified STMicroelectronics device is electrically and pin compatible.
MCP6042-I/MS vs MCP6042T-E/MS - which is better for industrial equipment?
MCP6042T-E/MS is generally the better candidate for industrial equipment that requires operation across the extended temperature range, while MCP6042-I/MS is suitable when its specified operating range covers the enclosure environment. Both devices belong to the MCP6042 family and use the 8-pin MSOP package, enabling the same PCB footprint. The choice should be based on the exact temperature grade, operating ambient, qualification requirements, and availability rather than on a simple performance difference.
Where can I buy MCP6042-I/MS online?
Use the Request a Quote form on this page to request MCP6042-I/MS pricing, current availability, and lead time. The form allows you to specify the required quantity, package format, and delivery needs without relying on a static listing. For technical validation, confirm that the quoted part number is exactly MCP6042-I/MS and that the shipment format matches the board's assembly process.
What is the price of MCP6042-I/MS?
The current unit price and quantity pricing for MCP6042-I/MS are presented through the Request a Quote form on this page. Use that form to request pricing for the required quantity and obtain a current commercial quotation. The structured pricing attached to this listing reflects the latest exact-part listing captured for comparison, while the quote form provides the appropriate channel for a transaction-specific response.
What is the lead time and stock status for MCP6042-I/MS?
Request the current MCP6042-I/MS stock position, lead time, and minimum order quantity through the Request a Quote form on this page. Commercial inventory can vary with quantity and shipment format, so a current quotation is more useful than a generic availability statement. Include your production quantity, required delivery date, and acceptable packing method when submitting the request.

工程参考数据: MCP6042-I/MS ——对比、设计指导和合规信息。

选型指南

Choose MCP6042-I/MS for compact, low-power analog circuits that need two general-purpose amplifier channels, rail-to-rail input and output behavior, and very low input bias current. It is particularly suitable for battery-operated sensor interfaces, portable instrumentation, and low-frequency data-acquisition channels operating from 1.4 V to 5.5 V. MCP6042T-E/MS is the preferred same-family candidate when the enclosure temperature requires the extended-temperature ordering grade, while retaining the 8-pin MSOP footprint and core electrical characteristics. Other low-power or dual op amps should only be substituted after their pinout, common-mode range, output swing, bias current, gain-bandwidth product, and stability characteristics have been checked. A shared package alone is not sufficient evidence of drop-in compatibility.

与替代料对比

参数 本产品 MCP6042T-E/MS
Package 8-pin MSOP 8-pin MSOP
Brand Microchip Technology Microchip Technology
Number of Channels 2 channels 2 channels
Gain-Bandwidth Product 14 kHz 14 kHz
Slew Rate 3 V/µs 3 V/µs
Typical Operating Current 600 nA per amplifier 600 nA per amplifier
Input Bias Current 1 pA typical 1 pA typical
Input Offset Voltage Less than 3 mV Less than 3 mV
Supply Voltage Range 1.4 V to 5.5 V 1.4 V to 5.5 V
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output
Temperature Ordering Grade I grade E grade

关键差异点

  • Very low operating current for a dual amplifier (对比 MCP6042T-E/MS)
  • Low input bias current for high-impedance sources (对比 MCP6042T-E/MS)
  • Rail-to-rail operation from a 1.4 V supply (对比 MCP6042T-E/MS)
  • Compact dual-channel MSOP implementation (对比 MCP6042T-E/MS)

设计说明

Place the device close to the source and load circuitry, route the two amplifier channels symmetrically, and position input traces away from switching nodes and high-current return paths. For a high-impedance input, use a guard ring driven by the corresponding amplifier output where the application permits. Keep ground returns short and use a solid ground plane. The 8-pin MSOP package saves board area, but its fine pitch still requires aligned land patterns and adequate solder-mask clearance.

Evaluate the complete analog signal path at the minimum available supply voltage. The MCP6042-I/MS operates from 1.4 V to 5.5 V, but rail-to-rail output does not imply zero headroom under every output current or frequency. Confirm the required output level with the load, calculate the amplifier dissipation from the actual supply and output voltages, and ensure the power source can support the application. Add local supply bypass capacitance and route it directly between the supply and ground pins.

Do not treat the 14 kHz gain-bandwidth product as suitable for high-speed waveform amplification. Closed-loop bandwidth, noise gain, capacitive loading, and the 3 V/µs slew rate determine usable large-signal performance. Similarly, the 1 pA input bias current is only meaningful if the PCB, connectors, resistors, and surrounding humidity do not introduce greater leakage. Validate the complete assembly under temperature and humidity conditions relevant to the finished equipment.

Use short, guarded traces for the non-inverting inputs and keep the inverting-input node physically small because parasitic capacitance can alter stability and noise behavior. For transimpedance applications, include the photodiode and feedback capacitance in the stability analysis rather than adding arbitrary capacitance. Confirm settling performance for the intended signal bandwidth and use the manufacturer's application guidance when driving long cables or sampling nodes.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

No definitive environmental or automotive qualification statements were available for the exact MCP6042-I/MS ordering code. The MCP6042 family is associated with automotive-qualified variants, but qualification status must be confirmed for the selected manufacturer part number.

数据核验日期: 2026-11-15 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

mcp6042 datasheet mcp6042 datasheet pdf mcp6042 pinout MCP6042-I/MS datasheet MCP6042-I/MS pinout MCP6042-I/MS equivalent MCP6042-I/MS replacement MCP6042 14 kHz op amp MCP6042 600 nA amplifier MCP6042 8-pin MSOP MCP6042-I/MS price MCP6042-I/MS stock Microchip MCP6042-I/MS MCP6042 vs MCP6042T-E/MS

相关元器件 & 术语

Microchip Technology MCP6042 MCP6042-I/MS MCP6042T-E/MS MCP6041 MCP6043 MCP6044 operational amplifier op amp dual amplifier analog amplifier IC signal-conditioning IC rail-to-rail input rail-to-rail output CMOS 14 kHz gain-bandwidth product 600 nA operating current 1 pA input bias current 3 V/µs slew rate 8-pin MSOP MSOP family surface-mount package sensor interface portable instrumentation low-voltage data acquisition
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情