MX574ALEWI+TCDR - 12-Bit 25µs SAR ADC, 28-SOIC | Maxim Integrated
料号： MX574ALEWI+TCDR ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $28.5 | $28.50 |
| 10 | $25.65 | $256.50 |
| 100 | $22.8 | $2,280.00 |
| 500 | $19.95 | $9,975.00 |
| 1,000 | $17.1 | $17,100.00 |
MX574ALEWI+TCDR 概述
What is a SAR ADC? A successive-approximation-register ADC is a type of data converter that converts an analog input voltage into a digital code using a binary-search algorithm implemented with a comparator, a DAC, and a successive-approximation register. SAR ADCs occupy the sweet spot between slow integrating converters (which offer excellent linearity at low speed) and fast flash ADCs (which offer high speed but consume significant power and pin count). They deliver 8 to 18 bits of resolution at sample rates from a few hundred kSPS to a few MSPS, with deterministic latency, no pipeline delay, and very low power consumption - making them ideal for multiplexed data-acquisition systems, industrial process control, and instrumentation.
Key features of the MX574ALEWI+TCDR include ±1 LSB max integral linearity error (A-grade), 25µs maximum conversion time, a built-in +10V reference with ±0.25% initial accuracy, 12-bit parallel and serial interface options, and three-state output buffers that allow direct connection to microprocessor data buses. The device operates from ±12V or ±15V analog supplies with a +5V digital supply, and its bipolar-input capability simplifies signal-conditioning front ends for industrial sensors and audio equipment.
The MX574A architecture combines a precision thin-film resistor network, a CMOS comparator, a current-mode DAC, and a SAR register, all trimmed at the wafer level. This integration eliminates external trimming and allows designers to use the ADC immediately after power-up without calibration routines, which historically made the MX574A the de-facto industry-standard 12-bit ADC for both standalone and embedded data-acquisition boards.
Typical applications include industrial process control, multiplexed data-acquisition front ends, signal isolation front ends paired with opto-isolators, precision measurement instrumentation, audio digitizers, and embedded board-level designs where +12V supplies are available and -48V telecom battery monitoring is required.
When designing with this part, provide a clean +5V digital supply decoupled with 0.1µF and 10µF capacitors close to the supply pins. Use a separate analog ground plane for the input and reference sections, and route the 12-bit parallel bus away from the analog inputs to prevent digital coupling into the converter.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.
直接替换替代料： MX574ALEWI+TCDR ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： MX574ALEWI+TCDR （相同外形与封装尺寸） ——差异在于 Package, Data Interface, Input Type, Manufacturer, Number of Inputs.
快速对比工具——选择替代料号进行并排对比：
MX674ALEWI+TCDR
✅ 直接替换📋 参考替代料（不在目录中）
AD574AJN
✅ 直接替换📋 参考替代料（不在目录中）
MX574AJEWI+TCDR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MX574AKEWI+TCDR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MX574ACWI+TCDR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
MX574ALEWI+TCDR 最大额定值与电气特性
| Manufacturer | Analog Devices Inc. (formerly Maxim Integrated) |
| MPN | MX574ALEWI+TCDR |
| Converter Type | SAR (Successive Approximation Register) ADC |
| 分辨率 | 12 bit |
| Number of Inputs | 1 |
| Input Type | Single-Ended (unipolar or bipolar ranges via pin strapping) |
| Maximum Conversion Time | 25 µs |
| Sample Rate (max) | 40 kSPS (typ) |
| Analog Input Ranges | 0 to +5 V, 0 to +10 V, ±5 V, ±10 V (software/strap-selectable) |
| Internal Reference | +10 V buried Zener, ±0.25 % initial accuracy (typ) |
| Data Interface | 12-bit parallel, 8-bit parallel, or serial |
| 输出类型 | Three-state (high-Z) CMOS-compatible |
| Integral Nonlinearity (A grade) | ±1 LSB (max) |
| Supply Voltages | V+ = +12 V or +15 V, V- = -12 V or -15 V, VCC (digital) = +5 V |
| Power Consumption | 150 mW (typ, ±15 V supply) |
| 工作温度 | 0 °C to +70 °C (commercial, 'L' grade) |
| 封装 | 28-pin SOIC wide-body (SOIC-28W) |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
| AEC-Q100 | Not qualified (commercial grade) |
MX574ALEWI+TCDR 引脚配置
| 引脚 1 | VCC (+12V/+15V) — Positive analog supply |
| 引脚 2 | GND — Analog ground |
| 引脚 3 | REF OUT — +10V internal reference output |
| 引脚 4 | REF IN — Reference input (decoupled) |
| 引脚 5 | ANALOG IN — Analog input |
| 引脚 6 | BIP OFF — Bipolar offset trim |
| 引脚 7 | GAIN — Gain trim |
| 引脚 8 | VEE (-12V/-15V) — Negative analog supply |
| 引脚 9 | DB0 — Digital output bit 0 (LSB) |
| 引脚 10 | DB1 — Digital output bit 1 |
| 引脚 11 | DB2 — Digital output bit 2 |
| 引脚 12 | DB3 — Digital output bit 3 |
| 引脚 13 | DB4 — Digital output bit 4 |
| 引脚 14 | DB5 — Digital output bit 5 |
| 引脚 15 | DB6 — Digital output bit 6 |
| 引脚 16 | DB7 — Digital output bit 7 |
| 引脚 17 | DB8 — Digital output bit 8 |
| 引脚 18 | DB9 — Digital output bit 9 |
| 引脚 19 | DB10 — Digital output bit 10 |
| 引脚 20 | DB11 (MSB) — Digital output bit 11 (MSB) |
| 引脚 21 | +5V — Digital +5V supply |
| 引脚 22 | DGND — Digital ground |
| 引脚 23 | STS — Status output (active low) |
| 引脚 24 | R/C — Read/Convert input |
| 引脚 25 | CE — Chip enable |
| 引脚 26 | VEE (-12V/-15V) — Negative supply (digital) |
| 引脚 27 | VCC (+12V/+15V) — Positive supply (digital) |
| 引脚 28 | MODE — Mode select (12/8 bit / unipolar/bipolar) |
典型应用
MX574ALEWI+TCDR 适用于 6 应用s: Industrial Process Control Data Acquisition, Multiplexed Data-Acquisition Front Ends, Signal Isolation Front End (Opto-Isolated ADC), Precision Measurement Instrumentation, Audio Band Digitizers and Prosumer Recorders, Embedded Board-Level and Retro-Computing Designs.
Industrial Process Control Data Acquisition
The MX574ALEWI+TCDR fits industrial process-control front ends where 4-20 mA or ±10 V transducer signals must be digitized with 12-bit accuracy at moderate throughput. Its ±10 V bipolar input range accepts signals directly from instrumentation amplifiers and strain-gauge bridges without external scaling, while the 25 µs conversion time (40 kSPS) is more than sufficient for thermal, pressure, and flow-loop update rates. The on-chip +10 V reference eliminates one precision component on the BOM. When deployed on a 16-channel multiplexer, the part can digitize a full rack of PLC analog inputs in well under 1 ms with negligible crosstalk from its 12-bit three-state parallel output.
推荐
Multiplexed Data-Acquisition Front Ends
For multiplexed data-acquisition boards with multiple analog channels, the MX574ALEWI+TCDR serves as the master digitizer driving the parallel bus of a microprocessor. Its 12-bit three-state output connects directly to a microcontroller data bus without glue logic, and its 25 µs conversion allows an 8-channel MUX to be scanned at >400 Hz aggregate rate. The internal +10 V reference and bipolar input range simplify signal conditioning, while the wide-body SOIC-28 package provides good thermal headroom for continuous operation in densely populated backplanes.
推荐
Signal Isolation Front End (Opto-Isolated ADC)
The MX574ALEWI+TCDR pairs naturally with digital isolators or opto-couplers for high-voltage or noise-immune isolation front ends. Place the ADC on the 'field' side of the isolation barrier, run its 12-bit parallel output through opto-isolators or iCouplers, and the high-voltage side of the system becomes immune to ground loops and common-mode surges. The 25 µs conversion latency fits the typical propagation delay of optocouplers, and the SOIC-28 package fits standard industrial isolation board footprints.
推荐
Precision Measurement Instrumentation
Bench-top multimeters, calibrators, and laboratory digitizers benefit from the MX574ALEWI+TCDR's ±1 LSB A-grade linearity and on-chip +10 V reference. The ±10 V bipolar range matches the output of most instrumentation amplifiers used with thermocouples, RTDs, and load cells. The 25 µs conversion time is far faster than the integration time of bench DMMs, allowing oversampling for noise reduction while maintaining real-time throughput for production test systems.
推荐
Audio Band Digitizers and Prosumer Recorders
For audio bandwidth applications up to ~20 kHz, the MX574ALEWI+TCDR provides 12-bit (72 dB) dynamic range in a bipolar ±10 V configuration. While not suitable for high-end studio audio, the part fits consumer and prosumer audio digitizers, automotive head-unit ADC channels, and speech-recognition front ends. The 25 µs conversion time and parallel output allow direct connection to a DSP or microcontroller without buffering, and the SOIC-28 package fits standard 2-layer audio board designs.
推荐
Embedded Board-Level and Retro-Computing Designs
Embedded SBCs, retro-computer expansion boards, and industrial controllers use the MX574ALEWI+TCDR as a parallel-bus ADC that connects directly to 8085/Z80/6800-family microprocessors without glue logic. The 12-bit three-state output interfaces directly to 8-bit or 16-bit data buses via the 8-bit/12-bit mode strapping. The SOIC-28 footprint is also friendly to through-hole prototyping adapter boards, making this part a long-time favorite for educational lab kits and hobby projects that need an industry-standard ADC.
推荐
推荐产品汇总
工程参考数据： MX574ALEWI+TCDR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MX674ALEWI+TCDR | AD574AJN | MX574AJEWI+TCDR |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | SOIC-28W | SOIC-28W - same | SOIC-28W - same | SOIC-28W - same |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit |
| Maximum Conversion Time | 25 µs | 15 µs | 25 µs | 25 µs |
| Sample Rate (max) | 40 kSPS | 67 kSPS | 40 kSPS | 40 kSPS |
| Internal Reference | +10 V | +10 V | +10 V | +10 V |
| Analog Input Range | 0-5 / 0-10 / ±5 / ±10 V | 0-5 / 0-10 / ±5 / ±10 V | 0-5 / 0-10 / ±5 / ±10 V | 0-5 / 0-10 / ±5 / ±10 V |
| Operating Temperature | 0 °C to +70 °C | 0 °C to +70 °C | 0 °C to +70 °C | 0 °C to +70 °C |
| Power Consumption | 150 mW | 150 mW | 150 mW | 150 mW |
关键差异点
- Industry-standard pinout shared across decades of AD574 family （对比 Modern sigma-delta ADCs (e.g. MAX11209))
- On-chip precision +10 V reference （对比 AD574A predecessor with external reference requirement)
- Bipolar input range without external signal conditioning （对比 Single-supply ADCs requiring input scaling)
- 25 µs conversion is faster than legacy integrating ADCs （对比 ICL7106 integrating ADCs (typical 200 ms conversion))
设计说明
The MX574ALEWI+TCDR requires three supplies: V+ (+12 V or +15 V analog), V- (-12 V or -15 V analog), and VCC (+5 V digital). Decouple each analog supply with a 10 µF tantalum in parallel with a 0.1 µF ceramic placed as close as possible to the supply pins. Add a ferrite bead between the analog +5 V rail (used for the reference) and the noisy digital +5 V rail to prevent digital switching noise from coupling into the on-chip +10 V reference and degrading linearity.
Use a four-layer PCB with a continuous analog ground plane beneath the MX574ALEWI+TCDR. Route the 12-bit parallel DB0-DB11 bus on the opposite side of the board from the analog input trace, with each digital line carrying a series 33 Ω damping resistor to reduce switching transients coupling into the analog input. Place the external gain and offset trim potentiometers within 10 mm of pins 6 and 7, and connect their wiper arms directly to the appropriate trim pins with no shared ground noise.
Do not leave the analog input floating during power-up - the input bias current can drift the internal auto-calibration DAC and introduce a DC offset error on the first conversion. Tie the analog input to GND through a 10 kΩ resistor if no signal source is connected. Also, ensure R/C (pin 24) and CE (pin 25) are not both asserted simultaneously during power-up, or the part may latch into an undefined conversion state requiring a power-cycle to recover.
Drive the analog input with a low-impedance buffer op-amp such as the MAX4208 or OPA2277 with a series 10 Ω resistor at the ADC input pin. The MX574ALEWI+TCDR input draws transient current during the internal DAC settling; without the buffer, source impedance above 1 kΩ will degrade linearity and add gain error. Add a 1 nF capacitor in parallel with the 10 Ω resistor at the input pin to absorb the DAC switching transients.
合规信息
RoHS compliant per Maxim Integrated/Analog Devices product page. Commercial temperature grade (0 °C to +70 °C); not AEC-Q100 qualified - choose MAX174/MX574AEWI variants for industrial, MX574AM versions for military.
