NAFE13388-EVB - Evaluation Board for 24-bit 8-ch AFE | NXP
料号： NAFE13388-EVB ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
NAFE13388-EVB 概述
An evaluation board (EVB) is a printed-circuit platform that lets engineers assess an integrated circuit without designing custom hardware. In the data-conversion hierarchy, it belongs to development tools supporting analog front-end ICs: the AFE chip, then the ADC signal chain, then the complete measurement system. EVBs typically expose all signal pins, jumpers for configuration, and connectors to a host controller.
The NAFE13388-EVB is designed for the NAFExx388 family and connects to an NXP LPC54628 MCU board, allowing easy configuration and reading of measurement data through a dedicated PC GUI, per the NXP product page. This shortens the path from lab evaluation to production design.
The underlying NAFE13388 provides 1 Gohm high input impedance and input leakage below 5 nA at 105 C, which, combined with its low-noise, low-offset-drift PGA, makes it well suited for precision temperature measurement with RTD and thermocouple sensors, according to the NXP datasheet (Rev. 4, 2 April 2024). The eight HV analog inputs can be configured from eight single-ended to four differential channels with AICOM or AGND reference.
Typical evaluation scenarios include industrial sensor acquisition modules, battery test equipment, and building automation analog inputs. The integrated excitation sources support direct RTD and current-loop sensor evaluation.
When evaluating, note that the AFE integrates diagnostics; the GUI exposes configuration registers, so review the datasheet register map before scripting automated tests.
This page synthesizes distributor availability data, datasheet highlights, and practical evaluation guidance not consolidated in the manufacturer datasheet.
直接替换替代料： NAFE13388-EVB ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
快速对比工具——选择替代料号进行并排对比：
NAFE13388B-EVB
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
NAFE53388B-EVB
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
NAFE13398-EVB
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
NAFE13388-UADFLIP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
NAFE13388-EVB 规格参数（制造商发布）
| Product Type | Evaluation board (EVB) |
| Target Device | NAFE13388 universal analog front-end (AFE) |
| Analog Input Channels | 8 (configurable to 4 differential) |
| ADC Resolution | 24 bits |
| 输入电压范围 | +/-25 V (HV analog inputs) |
| PGA Gain Range | 0.2 V/V to 16 V/V (8 selectable settings) |
| Input Impedance | 1 Gohm |
| Input Leakage Current | < 5 nA at 105 C |
| Excitation Sources | Integrated (for RTD/sensor excitation) |
| Host Interface | Connects to NXP LPC54628 MCU board |
| Software Support | Dedicated PC GUI for configuration and data readout |
| Application Focus | Precision temperature measurement (RTD, TC), industrial DAQ |
| Manufacturer | NXP Semiconductors |
| Chip Datasheet Revision | Rev. 4, 2 April 2024 |
NAFE13388-EVB 接口与连接器
NAFE13388-EVB 提供制造商发布的以下接口和连接器：扩展 / 总线, 功率输入。扩展排针引脚定义、连接器引脚编号和电气限值在制造商文档中定义。
| 扩展 / 总线 | 24 bits |
| 功率输入 | +/-25 V (HV analog inputs) |
请参阅 制造商文档 以查看完整的扩展排针引脚和连接器引脚编号。
功率与热特性
| 功率输入 | +/-25 V (HV analog inputs) |
NAFE13388-EVB 的功率输入和热参数（由制造商发布）。
典型应用
NAFE13388-EVB 适用于 6 应用s: Industrial Sensor Data Acquisition, Precision Temperature Measurement (RTD), Thermocouple Input Modules, Battery Test and Monitoring Systems, Building Automation Analog Inputs, Process Control and Diagnostics.
Industrial Sensor Data Acquisition
The NAFE13388-EVB lets engineers prototype universal-input industrial DAQ channels using the NAFE13388's eight +/-25 V HV inputs, configurable from eight single-ended to four differential channels. The 24-bit ADC and PGA gains from 0.2 V/V to 16 V/V accommodate millivolt-level thermocouple signals through the +/-25 V tolerance typical of harsh industrial environments. With 1 Gohm input impedance and under 5 nA leakage at 105 C, loading errors on high-impedance sensors stay negligible. Evaluating via the LPC54628 board and NXP GUI lets designers validate register configurations and diagnostics before committing to a production schematic, cutting sensor-front-end development time substantially.
推荐
Precision Temperature Measurement (RTD)
RTD evaluation benefits directly from the EVB's integrated excitation sources: the NAFE13388 can source excitation current to 3-wire or 4-wire RTDs and measure the resulting voltage differentially, eliminating long wire runs of external circuitry. Per the NXP datasheet, the low-noise, low-offset-drift PGA paired with under 5 nA input leakage minimizes excitation-induced errors, supporting sub-degree accuracy designs. The 24-bit converter provides ample resolution over the 100-400 ohm span of a Pt100 or Pt1000 sensor. Using the EVB, engineers can compare gain settings (0.2 to 16 V/V) and verify ratiometric measurement performance before designing the final analog front end.
推荐
Thermocouple Input Modules
Thermocouple front ends demand high input tolerance and microvolt resolution. The NAFE13388's +/-25 V HV inputs survive miswiring and common-mode transients common in thermocouple installations, while the 24-bit ADC with high PGA gains resolves microvolt-level Seebeck signals. The AICOM common-input reference allows many thermocouple channels to share a reference, simplifying multichannel module design. The NAFE13388-EVB with the NXP GUI lets engineers measure noise floor and offset drift at each of the eight gain settings, quantify cold-junction channel requirements, and validate the integrated diagnostic features such as open-sensor detection before productization.
推荐
Battery Test and Monitoring Systems
Battery cell evaluation requires measuring many cells spanning a wide total voltage while each cell stays within a few volts. The NAFE13388's universal inputs tolerate +/-25 V, letting one AFE monitor stacks or individual cells with a shared AICOM reference. Its 1 Gohm inputs prevent cell drain during measurement, important for long-duration characterization. The EVB enables engineers to test differential configurations (up to four differential channels) against cell-voltage tolerances and to exercise the on-chip diagnostics used for open-wire detection in battery packs. The LPC54628 host plus GUI accelerates setup compared to building a custom DAQ harness.
推荐
Building Automation Analog Inputs
Building automation controllers mix universal analog inputs (0-10 V, resistive, thermistor, current loop) that historically required separate conditioning per type. The NAFE13388's universal +/-25 V inputs, programmable 0.2-16 V/V PGA, and integrated excitation sources let a single front-end cover all these modes, reducing BOM complexity. The EVB lets developers verify each input mode with the NXP GUI, from high-voltage 0-10 V signals to NTC thermistor ratiometric readings, and to calibrate channel-to-channel matching. Low 5 nA leakage protects accuracy on high-resistance sensor runs typical in HVAC installations across large buildings.
推荐
Process Control and Diagnostics
Process instrumentation requires both measurement precision and health monitoring. The NAFE13388 integrates various diagnostic features, according to NXP documentation, including sensor and wiring fault detection that the NAFE13388-EVB exposes through the PC GUI. Engineers can inject fault conditions (open sensor, shorted input, out-of-range +/-25 V signals) and observe diagnostic flag behavior at 24-bit resolution, validating alarm thresholds before deploying field hardware. The 8-channel universal architecture maps directly onto multi-loop process transmitters, and the low-power operation suits loop-powered 4-20 mA designs where the AFE's power budget is constrained.
推荐
推荐产品汇总
工程参考数据： NAFE13388-EVB ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | NAFE13388B-EVB | NAFE53388B-EVB | NAFE13398-EVB |
|---|---|---|---|---|
| Board Type | NAFExx388 evaluation board | NAFExx388 evaluation board (calibrated variant) | NAFExx388 evaluation board (high-speed variant) | NAFExx388 evaluation board (no excitation) |
| Package | Evaluation board (EVB form factor) | Evaluation board - same form factor | Evaluation board - same form factor | Evaluation board - same form factor |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Target ADC Resolution | 24 bits | 24 bits | 24 bits | 24 bits |
| Analog Input Range | +/-25 V universal | +/-25 V universal | +/-25 V universal | +/-25 V universal |
| Channels | 8 (to 4 differential) | 8 (to 4 differential) | 8 (to 4 differential) | 8 (to 4 differential) |
| Excitation Sources | Integrated | Integrated | Integrated | Not integrated |
| Speed Class | Low-power | Low-power | High-speed | Low-power |
关键差异点
- Universal +/-25 V inputs with integrated excitation （对比 NAFE13398-EVB)
- Factory-calibrated evaluation option （对比 NAFE13388B-EVB)
- High-speed evaluation path （对比 NAFE53388B-EVB)
设计说明
The NAFE13388-EVB requires the NXP LPC54628 MCU board as its host; it is not standalone. Order the LPC54628 board together with the EVB to avoid evaluation downtime. The dedicated PC GUI handles register configuration, but reviewing the NAFE13388 datasheet (Rev. 4, April 2024) register map is strongly recommended before running automated tests, since diagnostic features and excitation sources are register-controlled.
When evaluating at 24-bit resolution, keep the HV analog input leads short and use differential configuration for low-level signals such as thermocouples. The 1 Gohm input impedance makes the inputs susceptible to pickup; shielded cable and a solid AICOM or AGND reference connection prevent noise from dominating the low-noise PGA performance.
The NAFE13388 is a low-power AFE, but the integrated excitation sources add current draw when driving RTDs. During evaluation, budget excitation current separately from AFE quiescent consumption so measured supply behavior reflects production conditions. Estimated: a Pt100 excitation of 1 mA dominates a sub-mA AFE quiescent current, per typical RTD practice.
合规信息
Compliance data not present in the verified web data for this evaluation board as of 2026-09-13; consult the NXP product page for the latest environmental declarations.