Texas Instruments

OPA137PA - 36V 1MHz J-FET Op Amp | Texas Instruments

料号: OPA137PA ✓ 量产中
36 V Vdss ±10 pA Id 8-pin PDIP Package
最小起订量: 1 |

OPA137PA 概述

Texas Instruments OPA137PA is a single, 36 V, 1 MHz J-FET-input operational amplifier with rail-to-rail input to V+ in an 8-pin PDIP package. It combines very low input bias current, low quiescent current, and high open-loop gain for precision analog signal conditioning. Key operating characteristics include ±10 pA input bias current, 120 µA quiescent current per channel, and 145 dB open-loop gain.

An operational amplifier is a high-gain differential amplifier used to amplify, filter, buffer, or control analog signals. The OPA137 belongs to the operational-amplifier hierarchy within analog signal-chain ICs and power management systems. Its J-FET input stage is especially useful when source impedance can cause bias-current errors, while its low quiescent current suits battery-operated and compact instrumentation.

The amplifier offers a 1 MHz gain-bandwidth product, which makes it appropriate for audio and general-purpose precision applications rather than high-speed signal chains. Its rail-to-rail input range extends to the positive supply rail, allowing the input common-mode range to follow much of the available supply voltage. The 3.5 V/µs slew rate provides useful large-signal response without requiring the bandwidth of a modern high-speed amplifier.

OPA137PA operates from a maximum total supply voltage of 36 V, supporting a nominal ±18 V operating arrangement. The device is specified as a single amplifier rather than a dual or quad configuration. Its J-FET input topology provides low bias current, while the 145 dB open-loop gain supports high-precision closed-loop designs when paired with suitable feedback components.

Typical uses include low-level audio preamplification, photodiode and sensor interfaces, precision current-to-voltage conversion, active filters, and instrumentation buffers. The low input bias current is valuable when the source has high output impedance, while the 1 MHz bandwidth supports audio-band and moderate-frequency signal paths. Single-supply operation can also simplify portable equipment when the signal remains within the rail-to-rail input range.

A primary design consideration is common-mode range: although the input can approach V+, the output range, load, supply voltage, and selected gain must remain within the operating limits. Stable operation also requires suitable output isolation, compensation, and decoupling. Review the manufacturer pin description and typical-application circuits before assigning PCB functions or connecting feedback networks.

This page combines the manufacturer product information, ordering details, package data, application guidance, and verified drop-in alternatives with practical design notes. It also highlights the trade-offs between the OPA137PA's precision and low-bias characteristics and the different bandwidth or input-stage behavior of candidate replacements.

直接替换替代料: OPA137PA ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: OPA137PA (相同外形与封装尺寸) ——差异在于 Input Bias Current, Gain-Bandwidth Product, Open-Loop Gain, Product Family, Quiescent Current.

Texas Instruments
Input Bias Current: 50 pA
Gain-Bandwidth Product: 8 MHz
Open-Loop Gain: 600
对比 OPA137PA →
Texas Instruments
Input Bias Current: ±5 pA typical
Quiescent Current: 120 μA per channel
对比 OPA137PA →

OPA137P

✅ 直接替换
Texas Instruments
📦 8-pin PDIP
Single FET-input operational amplifier · Texas Instruments · To ±18 V · 36 V · 1 MHz · ±5 pA typical · 1.5 mV maximum · 120 μA per channel

联系询价

查看数据手册 →

TL061IP

✅ 直接替换
📦 8-pin PDIP
Same 8-pin PDIP footprint, but bipolar input replaces the J-FET input and input bias current is higher than OPA137PA's ±10 pA; gain-bandwidth and noise also differ

📋 参考替代料(不在目录中)

OPA134PA

✅ 直接替换
Texas Instruments
📦 8-pin PDIP
Single high-performance audio operational amplifier · 1 circuit · 8 MHz · 50 pA · 8 nV/√Hz · 0.00008% · 20 V/µs · 600

联系询价

查看数据手册 →

OPA137PA 最大额定值与电气特性

Amplifier Type Single J-FET-input operational amplifier
Number of Amplifier Channels 1 channel
Maximum Supply Voltage 36 V
Nominal Total Supply Voltage ±18 V
Gain-Bandwidth Product 1 MHz
Open-Loop Gain 145 dB
Input Bias Current ±10 pA
静态电流 120 µA per channel
Slew Rate 3.5 V/µs
Maximum Input Offset Voltage 15 mV
Input Common-Mode Range Rail-to-rail input to V+
封装 8-pin PDIP
Package Type Through-hole PDIP
Product Family MicroAmplifier
RoHS 状态 Compliant

OPA137PA 引脚配置

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
引脚 1 NC — Not connected (per datasheet)
引脚 2 -IN — Inverting input
引脚 3 +IN — Non-inverting input
引脚 4 V- — Negative supply connection
引脚 5 NC — Not connected (per datasheet)
引脚 6 OUT — Output
引脚 7 V+ — Positive supply connection
引脚 8 NC — Not connected (per datasheet)

典型应用

OPA137PA 适用于 6 应用s: Precision Sensor Signal Conditioning, Low-Level Audio Preamplification, Transimpedance Amplification, Active Audio Filters, Battery-Powered Instrumentation, Precision Voltage Buffering.

🧩

Precision Sensor Signal Conditioning

OPA137PA is well suited to high-impedance sensor front ends because its J-FET input stage provides approximately ±10 pA input bias current. That low current reduces the offset generated when the amplifier is connected to photodiodes, electrochemical sensors, or other high-source-impedance nodes. Its 145 dB open-loop gain supports precise closed-loop amplification, while the 1 MHz gain-bandwidth product is appropriate for sensors whose useful bandwidth is well below 1 MHz. Place a suitable feedback network close to the device and verify that sensor biasing keeps the input and output inside the common-mode and output-swing limits shown in the manufacturer datasheet.

🎧

Low-Level Audio Preamplification

The low input bias current and low-power operation of OPA137PA make it suitable for low-level audio preamplifiers, particularly when the source has appreciable impedance. Its ±10 pA input bias current helps prevent excessive DC offset in the signal path, and the 1 MHz gain-bandwidth product comfortably covers audio frequencies. The 36 V maximum supply permits a nominal ±18 V implementation when higher headroom is useful. Designers should still evaluate output swing, distortion, and closed-loop stability at the intended gain and load, because headroom and stability change as the feedback network is adjusted.

📷

Transimpedance Amplification

OPA137PA can serve as the active element in a transimpedance amplifier when very low input bias current is valuable and the required closed-loop bandwidth fits within the 1 MHz gain-bandwidth product. The J-FET input's ±10 pA bias current is helpful when converting microamp-level or nanoamp-level sensor currents into a measurable voltage. Feedback resistance determines the nominal conversion gain, so it must be balanced against input capacitance and the amplifier's noise and stability behavior. Use a guarded, low-leakage feedback node and follow the manufacturer application guidance for practical compensation and bandwidth control.

🔧

Active Audio Filters

OPA137PA is suitable for active filters operating within its approximately 1 MHz gain-bandwidth range, particularly when very high source impedance makes input bias current important. Its 120 µA quiescent current per channel supports compact, low-power analog sections, and the 145 dB open-loop gain can improve closed-loop accuracy near the selected operating frequency. Select resistor and capacitor values so the filter's closed-loop noise gain remains stable with the OPA137PA. The 3.5 V/µs slew rate also helps preserve waveform shape, although large-signal behavior and output loading must be checked at the lowest intended supply voltage.

🔋

Battery-Powered Instrumentation

OPA137PA's 120 µA quiescent current per channel makes it appropriate for low-power instrumentation that must preserve measurement accuracy rather than merely provide gain. Its J-FET input reduces bias-current error at the input, while the 1 MHz bandwidth allows the device to handle audio-band and general measurement signals. A compact implementation still needs careful attention to supply current, regulator noise, grounding, and the input common-mode range. The rail-to-rail input to V+ can help maximize usable signal range in a single-supply system, but output swing and load capability must remain compatible with the selected operating point.

📟

Precision Voltage Buffering

OPA137PA can buffer high-impedance voltage sources where the input must not significantly disturb the source. Its ±10 pA input bias current limits the error introduced by the amplifier input, and the 145 dB open-loop gain supports accurate voltage following. The 1 MHz gain-bandwidth product is suitable for slow control signals and audio-band measurements rather than high-speed data acquisition. In a unity-gain buffer, confirm stability, capacitive-load tolerance, and output-current requirements for the connected source and load, then place the feedback connection directly at the device pins to avoid additional instability.

推荐产品汇总

OPA137 Single-amplifier family for precision sensor interfaces 用于: Precision Sensor Signal Conditioning, Transimpedance Amplification, Active Audio Filters, Battery-Powered Instrumentation, Precision Voltage Buffering OPA2137 Dual-amplifier family option for dual-channel conditioning 用于: Precision Sensor Signal Conditioning, Low-Level Audio Preamplification, Active Audio Filters, Precision Voltage Buffering OPA134 Related J-FET-input audio amplifier family 用于: Low-Level Audio Preamplification OPA4137 Quad-family option for multiple sensor channels 用于: Transimpedance Amplification, Battery-Powered Instrumentation
What are the key specifications of OPA137PA that engineers should know?
The OPA137PA is a single, 36 V, 1 MHz J-FET-input operational amplifier with a rail-to-rail input range extending to V+. Its principal precision characteristics are ±10 pA input bias current, 120 µA quiescent current per channel, and 145 dB open-loop gain. The device also has a 3.5 V/µs slew rate and is supplied in an 8-pin PDIP package. According to the Texas Instruments OPA137 datasheet, these characteristics position it as a low-power general-purpose amplifier for audio, instrumentation, sensor-interface, and filtering circuits.
Where can I download the OPA137PA datasheet PDF?
The OPA137PA datasheet PDF is available from the official Texas Instruments OPA137 product page and the manufacturer's direct document link at https://www.ti.com/lit/ds/symlink/opa137.pdf. The document covers OPA137-family devices and includes the electrical characteristics, ordering information, pin descriptions, and application information needed for design work. Use the package-specific ordering table when confirming that OPA137PA corresponds to the 8-pin PDIP configuration before assigning PCB connections.
Where can I find the OPA137PA pinout?
The OPA137PA pinout is defined in the pin-description section of the Texas Instruments OPA137 datasheet. Its 8-pin PDIP configuration uses the standard operational-amplifier arrangement, including separate positive and negative supply pins and the offset-null, input, and output connections shown by the manufacturer. Use the package drawing and pin-description table together when laying out the PCB because the orderable suffix identifies the mechanical package rather than a generic 8-pin footprint.
What is the operating voltage of OPA137PA?
OPA137PA supports a maximum total supply voltage of 36 V and is commonly described for a nominal ±18 V supply. The manufacturer identifies it as a single 36 V operational amplifier within the OPA137 family. The actual usable supply combination must also satisfy the device's common-mode, output-swing, and power-dissipation requirements. When using a lower supply, verify that the input and output signals remain within the electrical limits stated in the Texas Instruments datasheet.
Why is the low input bias current of OPA137PA important?
The ±10 pA input bias current of OPA137PA reduces the DC error produced when the amplifier senses signals from a high-impedance source. Input bias current flowing through a source impedance creates an offset voltage, so lower current is especially useful with photodiodes, sensors, and high-value feedback networks. According to the Texas Instruments OPA137 datasheet, the J-FET input stage combines this low bias current with a 1 MHz gain-bandwidth product and 120 µA quiescent current per channel.
Is OPA137PA suitable for audio preamplifier applications?
Yes, OPA137PA is suitable for audio preamplifier and general audio-signal conditioning because its J-FET input supports low bias current and its 1 MHz gain-bandwidth product covers the audio range. The 36 V maximum supply also permits a nominal ±18 V analog arrangement, while the rail-to-rail input reaches V+. Actual headroom at the output and the achievable distortion must be checked against the selected gain and load in the manufacturer datasheet.
What is the difference between OPA137PA and OPA137P?
OPA137PA and OPA137P both identify members of the Texas Instruments OPA137 single-amplifier family, and the available ordering information identifies OPA137PA as the 8-pin PDIP configuration. Their exact temperature grade and ordering distinctions should be confirmed from the manufacturer ordering table before treating them as interchangeable. For PCB compatibility, verify that both are the same PDIP package and compare the electrical ratings, lifecycle status, and operating-temperature limits of the exact orderable part.
What can replace OPA137PA?
OPA137PA can be replaced only after confirming package, pinout, supply range, bandwidth, input bias current, offset, slew rate, and output capability. The documented candidates include OPA137P from Texas Instruments, TL061IP from Texas Instruments, and OPA134PA from the same manufacturer family. TL061IP uses a bipolar input stage rather than the OPA137PA's J-FET input, so its bias-current behavior differs significantly; it is suitable only where the changed input characteristics meet the application requirements.
Is OPA137PA the same as TL061IP?
No, OPA137PA and TL061IP are not electrically identical. OPA137PA is a J-FET-input amplifier with approximately ±10 pA input bias current and a 1 MHz gain-bandwidth product, while TL061IP is a bipolar-input JFET-family alternative whose input-bias behavior differs by orders of magnitude. Both can use an 8-pin PDIP footprint, but existing high-impedance sensor circuits must be re-evaluated because bias-current error and noise performance can change materially.
When should I choose OPA137PA over TL061IP?
Choose OPA137PA when very low input bias current is more important than the lower-cost characteristics of a bipolar-input amplifier. Its ±10 pA nominal input bias current is particularly advantageous for high-impedance sensors, long PCB interconnects, or high-value feedback resistors. TL061IP may be suitable for ordinary audio and general-purpose designs where source impedance is low, but its input-current error can degrade accuracy even when the 8-pin PDIP footprint remains unchanged.
What is the best Texas Instruments equivalent for OPA137PA?
OPA137P is the closest same-manufacturer candidate because it belongs to the OPA137 family and uses the same 8-pin PDIP format. It preserves the family’s low-power J-FET-input architecture rather than changing to a bipolar input like TL061IP. Before substitution, compare the exact temperature grade, offset-voltage limit, supply range, and lifecycle status in the manufacturer ordering information. A footprint-compatible device is not automatically guaranteed to preserve every production specification.
Can OPA134PA replace OPA137PA?
OPA134PA can be evaluated as an 8-pin PDIP replacement, but it is not a specification-for-specification match for every OPA137PA design. It uses a J-FET input stage and is associated with low-bias audio applications, making it closer to OPA137PA than a bipolar-input part. Engineers must still compare gain-bandwidth product, input offset, slew rate, supply limits, noise, and load behavior against the circuit requirements before approving the substitution.
Where can I buy OPA137PA and check its current lead time?
Use the Request a Quote form on this page to request OPA137PA pricing, current stock status, minimum order quantity, and lead time. The form allows the request to be matched to the exact 8-pin PDIP orderable MPN rather than a family-level listing. Quote requests also help confirm whether the required quantity is available in production packaging and whether any lifecycle or regional availability changes affect the schedule.
What is the price of OPA137PA?
The current OPA137PA unit price is presented through the Request a Quote form on this page. Price can vary with quantity, order breaks, inventory position, and the exact 8-pin PDIP orderable configuration, so a static amount can become inaccurate. Submit the required quantity and packaging needs through the quote form for current commercial information rather than relying on a family-level starting price.
Is OPA137PA in stock and what is its lead time?
Current OPA137PA inventory and lead time should be requested through the Request a Quote form on this page. Availability can vary by quantity and order code, and a product-page listing does not guarantee that a production quantity is immediately available. Include the target annual usage, prototype or production status, tube requirements, and requested delivery date when submitting the request so procurement can confirm the appropriate schedule.
Does OPA137PA meet RoHS and AEC-Q100 requirements?
OPA137PA is identified as RoHS compliant in the available component comparison information. No explicit AEC-Q100 qualification is identified for this exact orderable device, so the automotive qualification status should be treated as not confirmed rather than inferred from the manufacturer name. For an automotive program, request the exact quality-document and traceability information for the intended orderable part, and separately verify RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation through the manufacturer's compliance records.

工程参考数据: OPA137PA ——对比、设计指导和合规信息。

选型指南

Choose OPA137PA when a low-power, single-channel operational amplifier needs very low input bias current, approximately 145 dB open-loop gain, and a 1 MHz gain-bandwidth product in an 8-pin PDIP package. It is particularly appropriate for high-impedance sensors, precision buffers, audio-band filtering, and low-level audio signal paths. OPA137P is the preferred replacement when the same OPA137 family behavior is required, provided the exact temperature grade and ordering details are confirmed. OPA134PA should be considered for audio-oriented J-FET applications only after comparing offset, bandwidth, noise, slew rate, and supply limits. TL061IP offers an 8-pin PDIP alternative for ordinary low-impedance circuits, but its bipolar input creates substantially higher bias-current error. For every candidate, verify lifecycle status, supply range, common-mode limits, output swing, and production quantity through the Request a Quote process.

与替代料对比

参数 本产品 OPA137P TL061IP OPA134PA
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Channels 1 channel 1 channel 1 channel 1 channel
Input Stage J-FET J-FET Bipolar J-FET

关键差异点

  • Preserves the OPA137 family's low-bias J-FET behavior (对比 TL061IP)
  • Closest same-family architecture and package (对比 OPA134PA)
  • Family-identical replacement path (对比 OPA137P)

设计说明

Do not treat a matching PDIP footprint as proof of electrical interchangeability. OPA137PA uses a low-bias J-FET input, whereas TL061IP uses a bipolar input; replacing it can materially change input offset error, noise, and the usable source impedance. OPA137P is the preferred same-family candidate. For OPA134PA, compare offset voltage, bandwidth, slew rate, noise, and supply limits against the original circuit. Verify every pin function in the manufacturer pin-description table before PCB reuse.

Route the non-inverting and inverting inputs away from high-current supply paths and switching-node copper. For high-impedance sources, minimize leakage through board contamination, protection diodes, and nearby moisture; the OPA137PA's approximately ±10 pA bias current otherwise offers little margin if leakage approaches that level. Keep the feedback components and their sensitive input node compact, and place the supply bypass capacitor close to the V+ and V- pins with a short, low-inductance return path.

Design the feedback network for the operating frequency rather than relying only on the nominal 1 MHz gain-bandwidth product. Noise gain, source capacitance, and capacitive loading can reduce usable closed-loop bandwidth or cause instability. Begin with a conventional feedback topology, check the resulting noise gain across the signal range, and isolate the output from highly capacitive loads when necessary. Keep the 3.5 V/µs slew rate in view when calculating large-signal settling behavior.

Confirm the actual supply combination, output swing, and dissipation at maximum signal and load before choosing an amplifier architecture. OPA137PA supports a maximum total supply voltage of 36 V and a nominal ±18 V arrangement, but allowing the output to reach either rail may violate the usable output-swing limits. Use the manufacturer's typical application circuits as the starting point for supply bypassing, grounding, and feedback layout, then validate stability and thermal behavior in the final enclosure and load configuration.

合规信息

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Qualified
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

RoHS compliance is identified for OPA137PA. No explicit AEC-Q100 qualification is identified for this exact device, so it is recorded as not qualified rather than inferred. REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer's current compliance documentation.

相关搜索

opa137 datasheet OPA137PA datasheet OPA137PA datasheet pdf OPA137PA pinout OPA137PA 8-PDIP pinout OPA137PA specifications OPA137PA 36V 1MHz OPA137PA low input bias current Texas Instruments OPA137PA OPA137PA drop-in replacement OPA137PA vs OPA137P OPA137PA vs TL061IP OPA137PA price OPA137PA lead time OPA137PA application circuit

相关元器件 & 术语

Texas Instruments OPA137PA OPA137P TL061IP OPA134PA OPA137 OPA2137 OPA4137 operational amplifier single operational amplifier J-FET input bipolar input low-dropout power analog signal-chain IC rail-to-rail input input bias current gain-bandwidth product open-loop gain quiescent current slew rate PDIP-8 through-hole package MicroAmplifier RoHS AEC-Q100
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情