OPA705UA - 12V 1MHz Rail-to-Rail CMOS Op Amp | Texas Instruments
料号: OPA705UA ✓ 量产中OPA705UA 概述
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs while presenting high input impedance and low output impedance to the surrounding circuit. Operational amplifiers sit within the amplifier-IC hierarchy and are widely used as closed-loop gain stages, voltage followers, buffers, comparators, filters, and active front ends for sensors and data-conversion systems. The OPA705 combines that general-purpose function with low-cost CMOS construction and a compact SOIC footprint.
The principal features of the OPA705UA are its 1 MHz gain-bandwidth product, rail-to-rail input and output operation, single-supply operation from 4 V to 12 V, dual-supply operation from ±2 V to ±6 V, and a single amplifier channel per package. Rail-to-rail input behavior is valuable when sensing signals near either supply rail, while rail-to-rail output capability provides more usable output range than a conventional amplifier limited to the rails.
OPA705UA is designed for low-cost, general-purpose applications rather than precision instrumentation. The manufacturer classifies the device as a single, 12 V, 1 MHz operational amplifier. Its 8-pin SOIC package provides a familiar pin arrangement and a practical upgrade path from other single-channel SOIC operational amplifiers when the circuit requires compatible supply voltage, input/output range, and signal bandwidth. Input common-mode and output swing limits must still be checked against the actual supply voltage and load.
Typical uses include sensor-signal conditioning, current measurement, low-frequency active filters, audio and communication interfaces, industrial control loops, and low-voltage portable equipment. A unity-gain voltage follower can buffer a high-impedance sensor, while a non-inverting amplifier stage can provide gain without placing substantial current on the sensor. The 1 MHz bandwidth is also appropriate for control and instrumentation paths that do not require the higher bandwidth of a high-speed amplifier.
When using OPA705UA, verify input common-mode range, output swing, stability with capacitive loads, and noise performance at the signal bandwidth of interest. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because this is a low-cost CMOS amplifier, applications demanding very low offset voltage, bias current, distortion, or noise should compare it with precision families before finalizing the design.
This page combines the exact ordering information for OPA705UA with package and pinout guidance, same-footprint replacement options, parameter comparisons, and practical design notes. It is intended to help engineers determine whether the 12 V, 1 MHz, rail-to-rail CMOS amplifier fits the electrical and mechanical requirements of a new analog circuit without overlooking supply-range or stability constraints.
直接替换替代料: OPA705UA ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: OPA705UA (相同外形与封装尺寸) ——差异在于 Dual-Supply Operating Range, Package.
OPA703UA
✅ 直接替换联系询价
查看数据手册 →OPA704UA
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →OPA706UA
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
OPA707UA
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV9101ID
✅ 直接替换📋 参考替代料(不在目录中)
OPA705UA 最大额定值与电气特性
| Number of Amplifier Channels | 1 channel |
| Maximum Total Supply Voltage | 12 V |
| Single-Supply Operating Range | 4 V to 12 V |
| Dual-Supply Operating Range | ±2 V to ±6 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Type | Rail-to-Rail I/O |
| 输出类型 | Rail-to-Rail I/O |
| Process Technology | CMOS |
| Application Classification | Standard general-purpose amplifier |
| 封装 | 8-SOIC, 0.154 in (3.90 mm) wide |
| 安装类型 | Surface mount |
OPA705UA 引脚配置
| 引脚 1 | NC — Not connected |
| 引脚 2 | IN- — Inverting input |
| 引脚 3 | IN+ — Non-inverting input |
| 引脚 4 | V- — Negative supply connection |
| 引脚 5 | NC — Not connected |
| 引脚 6 | OUT — Amplifier output |
| 引脚 7 | V+ — Positive supply connection |
| 引脚 8 | NC — Not connected |
典型应用
OPA705UA 适用于 6 应用s: Low-Voltage Sensor Signal Conditioning, Current Measurement Front End, Low-Frequency Active Filtering, Industrial Control and Instrumentation, Audio and Communication Interface Buffering, Portable and Battery-Powered Equipment.
Low-Voltage Sensor Signal Conditioning
OPA705UA is appropriate for buffering and scaling low-voltage sensor outputs where the amplifier must operate from a compact 4 V to 12 V single supply. Its rail-to-rail input and output architecture provides useful signal range near the supply rails, while the 1 MHz gain-bandwidth product is sufficient for many temperature, pressure, light, and industrial-control sensors. Place the device in a non-inverting or differential stage and confirm that the sensor signal remains inside the amplifier's input common-mode range. Output swing, offset, noise, and capacitive loading should be checked against the required measurement accuracy and sensor cable length.
推荐
Current Measurement Front End
OPA705UA can amplify the small voltage produced by a shunt resistor in low-voltage current-measurement circuits. Its 1 MHz gain-bandwidth product supports bandwidths well beyond ordinary slow current monitoring, and rail-to-rail I/O operation can improve utilization of a restricted supply range. Use the amplifier in a differential or subtractive configuration when the shunt voltage is small relative to offset and noise. Verify shunt heating, amplifier offset, input bias current, output swing, and whether the selected gain and compensation provide stable operation across the expected current range.
推荐
Low-Frequency Active Filtering
OPA705UA is suitable for first-order and moderate-order active filters built around 4 V to 12 V single-supply operation. Its 1 MHz gain-bandwidth product leaves substantial bandwidth margin over filters intended for audio, control, or low-frequency sensor signals, reducing the risk that finite closed-loop bandwidth will distort the intended response. The rail-to-rail input and output characteristics can support filters whose signal range approaches the supply rails. Component tolerances, amplifier noise, input bias current, and capacitive stability should be considered when setting resistor and capacitor values.
推荐
Industrial Control and Instrumentation
OPA705UA can serve as a general-purpose error amplifier in compact industrial control and instrumentation boards operating from a 4 V to 12 V rail. Its single-channel CMOS design fits analog monitoring, actuator-control, and signal-conditioning blocks where a higher-bandwidth amplifier is unnecessary. The 1 MHz bandwidth supports many control loops and low-frequency measurement channels, while the compact 8-SOIC package simplifies assembly. Designers should still review offset, bias current, noise, common-mode range, and output-current capability, particularly when the amplifier drives a sensor, relay driver, or downstream converter.
推荐
Audio and Communication Interface Buffering
OPA705UA can buffer low-level audio or communication signals in compact mixed-signal designs that use a 4 V to 12 V supply. The 1 MHz gain-bandwidth product covers a substantial portion of the audio range and many low-speed interface signals, while rail-to-rail I/O behavior can improve utilization of the available signal range. The device is best suited to low-cost, noncritical channels rather than high-fidelity audio paths with demanding noise and distortion limits. Check output swing into the actual load, input noise, offset, channel separation where relevant, and stability when driving capacitive inputs or long interconnects.
推荐
Portable and Battery-Powered Equipment
OPA705UA is suitable for low-voltage portable equipment that operates within its specified 4 V to 12 V supply range and does not require a very-low-power zero-drift amplifier. A single amplifier in an 8-SOIC package can provide gain or buffering for sensors, interface logic, and control signals. Battery operation makes supply current an important selection criterion, so verify the operating current and current required by the surrounding analog block. Check the amplifier's behavior during battery transitions, confirm common-mode limits at the minimum battery voltage, and assess shutdown requirements if the device is expected to remain connected to a depleted battery.
推荐
推荐产品汇总
工程参考数据: OPA705UA ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | OPA703UA | OPA704UA | OPA706UA | OPA707UA | TLV9101ID |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC - same package | 8-SOIC - same package | 8-SOIC - same package | 8-SOIC - same package | 8-SOIC - same package |
| Amplifier Channels | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Maximum Supply Voltage | 12 V | 12 V | 12 V | 12 V | 12 V | 16 V |
关键差异点
- Low-cost general-purpose rail-to-rail amplifier (对比 OPA703UA)
- Directly identified higher-voltage replacement path (对比 TLV9101ID)
- Single-channel SOIC implementation with rail-to-rail I/O (对比 OPA707UA)
设计说明
Place the supply-bypass capacitors immediately adjacent to the OPA705UA V+ and V- pins, and keep the input, feedback, and output routes compact. The 8-SOIC footprint provides little space, so excessive loop area can increase susceptibility to capacitive feedback. Keep high-current return paths away from the inverting-input node and connect analog ground using a deliberate return strategy rather than allowing high-current ground paths to share a narrow trace with the amplifier.
Do not assume that a rail-to-rail designation makes every input and output condition valid. Check the OPA705UA common-mode range at the lowest operating supply voltage, especially for battery-powered systems, and verify output swing at the required load current. Also account for the difference between single-supply and dual-supply operation: a 12 V single supply is not interchangeable with +12 V and -12 V rails because the total supply span would be 24 V.
The 1 MHz gain-bandwidth product makes OPA705UA suitable for low- and moderate-frequency signal paths, but closed-loop bandwidth does not remove the need for stable compensation. Use the manufacturer's recommended configuration for the intended closed-loop gain and evaluate the complete circuit with realistic sensor capacitance, cable capacitance, and output loading. If the source can present significant capacitance, include an isolation resistor or another documented compensation method and verify stability with oscilloscope measurements.
Operating from 4 V to 12 V places the OPA705UA in a low-voltage analog environment where the bypass network is critical. Use short, low-inductance connections from the supply pins to local capacitors and provide adequate return paths for transient current. When the amplifier follows a switching converter, place the regulator and amplifier on the appropriate power plane partition, keep the switching loop compact, and confirm that residual supply ripple does not consume the signal headroom required by the application.
合规信息
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established for the exact OPA705UA ordering suffix. The OPA705UA is a general-purpose commercial amplifier rather than an AEC-Q100 automotive-qualified option.