PCM1602Y/2K - 24-Bit 6-Channel 192kHz DAC | Texas Instruments
料号: PCM1602Y/2K ✓ 量产中PCM1602Y/2K 概述
An audio DAC is a mixed-signal semiconductor that converts digital PCM audio samples into left- and right-channel analog voltage signals. A six-channel DAC can drive three stereo pairs, making the device suitable for multichannel audio equipment, home-theater systems, digital mixing consoles, and active speaker designs. Within the broader hierarchy, PCM1602Y/2K belongs to the audio DAC, data converter, and signal-conversion IC categories.
The primary features of PCM1602Y/2K include 24-bit resolution, a 192 kHz maximum sampling rate, six output channels, enhanced multilevel delta-sigma architecture, and an I2S interface. The six-channel architecture reduces the number of separate stereo DACs required in a multichannel design, while the 192 kHz capability supports high-resolution audio signal paths. Its 48-LQFP package provides a defined surface-mount footprint for audio equipment with moderate connector density.
The enhanced multilevel delta-sigma architecture performs digital-to-analog conversion by shaping quantization noise away from the signal band and reconstructing the analog waveform through an internal conversion network and output stage. The 3.41 V maximum analog output provides a defined upper limit for the converter's analog output range. Its 400 microsecond nominal settling time describes the response interval associated with the device's settling behavior and is an important consideration when channels must be initialized or updated in a controlled sequence.
Typical uses include six-channel consumer audio receivers, home-theater preamplifiers, digital mixing consoles, multichannel headphone and line-output boards, active loudspeaker electronics, and professional audio interfaces. In each case, the I2S interface can accept digital audio from a source processor, while six analog outputs reduce channel-conversion component count. Stereo-only equipment would use only the required channel pairs, but the unused outputs must still be handled according to the manufacturer’s application guidance.
The most important design consideration is analog-output implementation. Follow the manufacturer’s reference circuit for output filtering, grounding, bypass capacitance, and digital-interface timing, and preserve the specified 3.41 V maximum analog output. Keep high-current digital and switching circuitry away from the analog output network, and use a quiet ground-plane strategy to reduce channel-to-channel noise coupling.
This product page organizes the converter’s verified capabilities, package information, sourcing paths, application guidance, and available same-footprint comparison. It also separates practical design guidance from raw specifications so engineers can evaluate the PCM1602Y/2K for multichannel audio systems before committing to a board design.
直接替换替代料: PCM1602Y/2K ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
PCM1602APTR
✅ 直接替换📋 参考替代料(不在目录中)
PCM1602Y/2K 最大额定值与电气特性
| Converter Type | 24-bit enhanced multilevel delta-sigma audio DAC |
| Number of Output Channels | 6 channels |
| Bit Resolution | 24 bit |
| Maximum Sampling Rate | 192 kHz |
| Digital Audio Interface | I2S |
| Maximum Analog Output | 3.41 V |
| Nominal Settling Time | 400 us |
| 工作温度范围 | -25°C to +85°C |
| 封装 | 48-LQFP, 7 mm x 7 mm |
| Total Pin Count | 48 pins |
| 安装类型 | Surface mount |
| Analog Output Configuration | 6-channel audio DAC |
| Converter Architecture | Enhanced multilevel delta-sigma |
| Audio Application | Multichannel audio conversion |
PCM1602Y/2K 48-lqfp, 7 mm x 7 mm 引脚配置指南
PCM1602Y/2K(48-lqfp, 7 mm x 7 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: PCM1602Y/2K.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PCM1602Y/2K 适用于 6 应用s: Home-Theater Receiver, Digital Mixing Console, Multichannel Audio Preamp, Professional Audio Interface, Active Loudspeaker Electronics, Digital Speaker and Amplifier System.
Home-Theater Receiver
The PCM1602Y/2K fits a home-theater receiver that must convert digital surround-sound audio into six analog outputs. Its six-channel architecture maps to three stereo output pairs, while the 24-bit resolution and 192 kHz maximum sampling rate support high-resolution source material. The I2S interface allows connection to a digital audio processor, and the maximum analog output is specified at 3.41 V. The implementation should follow the manufacturer’s reference circuit for output filtering, bypass placement, and grounding. Engineers should also verify the receiver’s supported sample rates and clock topology before finalizing the digital interface.
推荐
Digital Mixing Console
A digital mixing console can use the PCM1602Y/2K to convert processed digital channels into analog line-level outputs. Six channels provide three stereo busses in a single converter, simplifying synchronization across multiple output pairs. The 192 kHz maximum rate supports high-rate studio workflows, while the 24-bit architecture preserves substantial numerical detail through conversion. Because the 400 microsecond nominal settling time influences channel-update behavior, console designers should confirm timing requirements against the finished signal path. Output filtering, analog grounding, and channel-to-channel isolation should follow the manufacturer’s recommended application layout.
推荐
Multichannel Audio Preamp
The PCM1602Y/2K is suitable for a multichannel preamplifier requiring three synchronized stereo analog outputs. A single six-channel converter reduces the number of audio conversion packages compared with separate stereo DACs, while the I2S input accepts digital audio from a source-control device. Its 24-bit, 192 kHz capability suits modern high-resolution audio paths. The maximum analog output of 3.41 V provides the design boundary for downstream gain stages, but the actual signal level depends on the manufacturer’s output-network implementation. Verify output swing, filtering, and grounding before sizing line-driver and coupling circuitry.
推荐
Professional Audio Interface
The PCM1602Y/2K can support multichannel outputs in a professional audio interface when the interface uses an I2S digital audio path. Six converter outputs allow three stereo monitor or playback channels to share one device, and the maximum 192 kHz rate accommodates high-resolution multichannel workflows. The nominal 400 microsecond settling time is relevant when multiple channels are enabled or updated as a group. For low-noise performance, place the analog outputs and their reconstruction filters away from digital clocks and switching converters. The final channel count and operating mode must be selected from the manufacturer’s supported configuration tables.
推荐
Active Loudspeaker Electronics
The PCM1602Y/2K can serve as the digital-to-analog stage in an active loudspeaker controller or multiway amplifier board that accepts I2S audio. Its six outputs permit three stereo groups to be converted before amplification and crossover processing. The 24-bit resolution and 192 kHz maximum rate support high-fidelity digital source signals, while the 48-LQFP package provides a defined surface-mount implementation. The designer must preserve analog return paths and implement the manufacturer’s required output filtering. For an 8-channel system, two six-channel converters may be needed, subject to valid clocking and channel-mapping requirements.
推荐
Digital Speaker and Amplifier System
The PCM1602Y/2K fits a digital speaker or networked-amplifier system that receives multichannel I2S audio and requires local analog conversion. Three stereo output groups can feed amplification and crossover stages from one converter, reducing package count compared with separate stereo devices. The 192 kHz sampling capability is useful when the upstream system transports high-rate audio, and the 24-bit resolution supports detailed signal reconstruction. Because the converter’s analog output is limited to 3.41 V, downstream amplifier gain must be selected accordingly. Validate the reference output network, channel mapping, and thermal performance of the complete amplifier board.
推荐
推荐产品汇总
工程参考数据: PCM1602Y/2K ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PCM1602APTR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) |
| Converter Type | Enhanced multilevel delta-sigma DAC | Enhanced multilevel delta-sigma DAC |
| Resolution | 24 bit | 24 bit |
| Output Channels | 6 channels | 6 channels |
| Maximum Sampling Rate | 192 kHz | 192 kHz |
| Digital Interface | I2S | I2S |
关键差异点
- Six-channel integration in one converter (对比 PCM1602APTR)
- Direct six-channel I2S audio conversion (对比 PCM1602APTR)
- Defined 3.41 V analog-output boundary (对比 PCM1602APTR)
- Defined nominal settling behavior (对比 PCM1602APTR)
设计说明
Place the PCM1602Y/2K analog-output network and its bypass components close to the converter pins, and route digital clock and data traces away from sensitive output nodes. Use the manufacturer’s reference layout to determine component placement and trace geometry for the 48-LQFP footprint. Continuous ground-plane construction is generally preferable to fragmented return paths because the device combines a high-speed digital interface with analog output stages.
Follow the manufacturer’s supply, bypass-capacitor, and power-sequence recommendations exactly. Decoupling components should be positioned at the relevant supply pins with short, direct connections so switching noise does not propagate into the converter’s analog outputs. Before finalizing amplifier gain or coupling networks, confirm that downstream circuitry remains compatible with the specified 3.41 V maximum analog output and the device’s actual output-swing conditions.
Do not treat PCM1602Y, PCM1602Y/2K, and PCM1602APTR as interchangeable solely because their product names are similar. Confirm the exact ordering suffix, pin functions, package, and interface configuration before releasing a purchase order or replacement. For an existing PCB, use the manufacturer’s pin-description table and application circuit rather than inferring connections from another package or ordering configuration.
合规信息
No compliance declarations were identified in the retrieved product information. The component is an audio converter IC rather than an automotive-qualified device.