PCM1602Y/2K - 24-Bit 6-Channel 192kHz DAC | Texas Instruments
MPN: PCM1602Y/2K ✓ Hoạt độngPCM1602Y/2K Tóm tắt
An audio DAC is a mixed-signal semiconductor that converts digital PCM audio samples into left- and right-channel analog voltage signals. A six-channel DAC can drive three stereo pairs, making the device suitable for multichannel audio equipment, home-theater systems, digital mixing consoles, and active speaker designs. Within the broader hierarchy, PCM1602Y/2K belongs to the audio DAC, data converter, and signal-conversion IC categories.
The primary features of PCM1602Y/2K include 24-bit resolution, a 192 kHz maximum sampling rate, six output channels, enhanced multilevel delta-sigma architecture, and an I2S interface. The six-channel architecture reduces the number of separate stereo DACs required in a multichannel design, while the 192 kHz capability supports high-resolution audio signal paths. Its 48-LQFP package provides a defined surface-mount footprint for audio equipment with moderate connector density.
The enhanced multilevel delta-sigma architecture performs digital-to-analog conversion by shaping quantization noise away from the signal band and reconstructing the analog waveform through an internal conversion network and output stage. The 3.41 V maximum analog output provides a defined upper limit for the converter's analog output range. Its 400 microsecond nominal settling time describes the response interval associated with the device's settling behavior and is an important consideration when channels must be initialized or updated in a controlled sequence.
Typical uses include six-channel consumer audio receivers, home-theater preamplifiers, digital mixing consoles, multichannel headphone and line-output boards, active loudspeaker electronics, and professional audio interfaces. In each case, the I2S interface can accept digital audio from a source processor, while six analog outputs reduce channel-conversion component count. Stereo-only equipment would use only the required channel pairs, but the unused outputs must still be handled according to the manufacturer’s application guidance.
The most important design consideration is analog-output implementation. Follow the manufacturer’s reference circuit for output filtering, grounding, bypass capacitance, and digital-interface timing, and preserve the specified 3.41 V maximum analog output. Keep high-current digital and switching circuitry away from the analog output network, and use a quiet ground-plane strategy to reduce channel-to-channel noise coupling.
This product page organizes the converter’s verified capabilities, package information, sourcing paths, application guidance, and available same-footprint comparison. It also separates practical design guidance from raw specifications so engineers can evaluate the PCM1602Y/2K for multichannel audio systems before committing to a board design.
Bộ thay thế dễ dàng lắp đặt cho PCM1602Y/2K — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
PCM1602APTR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PCM1602Y/2K Tỷ lệ tối đa & tính chất điện
| Converter Type | 24-bit enhanced multilevel delta-sigma audio DAC |
| Number of Output Channels | 6 channels |
| Bit Resolution | 24 bit |
| Maximum Sampling Rate | 192 kHz |
| Digital Audio Interface | I2S |
| Maximum Analog Output | 3.41 V |
| Nominal Settling Time | 400 us |
| Khoảng nhiệt độ hoạt động | -25°C to +85°C |
| Hộp | 48-LQFP, 7 mm x 7 mm |
| Total Pin Count | 48 pins |
| Kiểu lắp đặt | Surface mount |
| Analog Output Configuration | 6-channel audio DAC |
| Converter Architecture | Enhanced multilevel delta-sigma |
| Audio Application | Multichannel audio conversion |
Hướng dẫn cấu hình chân PCM1602Y/2K 48-lqfp, 7 mm x 7 mm
Cấu hình chân cho PCM1602Y/2K (48-lqfp, 7 mm x 7 mm gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho PCM1602Y/2K.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PCM1602Y/2K phù hợp cho 6 Áp dụngs: Home-Theater Receiver, Digital Mixing Console, Multichannel Audio Preamp, Professional Audio Interface, Active Loudspeaker Electronics, Digital Speaker and Amplifier System.
Home-Theater Receiver
The PCM1602Y/2K fits a home-theater receiver that must convert digital surround-sound audio into six analog outputs. Its six-channel architecture maps to three stereo output pairs, while the 24-bit resolution and 192 kHz maximum sampling rate support high-resolution source material. The I2S interface allows connection to a digital audio processor, and the maximum analog output is specified at 3.41 V. The implementation should follow the manufacturer’s reference circuit for output filtering, bypass placement, and grounding. Engineers should also verify the receiver’s supported sample rates and clock topology before finalizing the digital interface.
Được đề xuất
Digital Mixing Console
A digital mixing console can use the PCM1602Y/2K to convert processed digital channels into analog line-level outputs. Six channels provide three stereo busses in a single converter, simplifying synchronization across multiple output pairs. The 192 kHz maximum rate supports high-rate studio workflows, while the 24-bit architecture preserves substantial numerical detail through conversion. Because the 400 microsecond nominal settling time influences channel-update behavior, console designers should confirm timing requirements against the finished signal path. Output filtering, analog grounding, and channel-to-channel isolation should follow the manufacturer’s recommended application layout.
Được đề xuất
Multichannel Audio Preamp
The PCM1602Y/2K is suitable for a multichannel preamplifier requiring three synchronized stereo analog outputs. A single six-channel converter reduces the number of audio conversion packages compared with separate stereo DACs, while the I2S input accepts digital audio from a source-control device. Its 24-bit, 192 kHz capability suits modern high-resolution audio paths. The maximum analog output of 3.41 V provides the design boundary for downstream gain stages, but the actual signal level depends on the manufacturer’s output-network implementation. Verify output swing, filtering, and grounding before sizing line-driver and coupling circuitry.
Được đề xuất
Professional Audio Interface
The PCM1602Y/2K can support multichannel outputs in a professional audio interface when the interface uses an I2S digital audio path. Six converter outputs allow three stereo monitor or playback channels to share one device, and the maximum 192 kHz rate accommodates high-resolution multichannel workflows. The nominal 400 microsecond settling time is relevant when multiple channels are enabled or updated as a group. For low-noise performance, place the analog outputs and their reconstruction filters away from digital clocks and switching converters. The final channel count and operating mode must be selected from the manufacturer’s supported configuration tables.
Được đề xuất
Active Loudspeaker Electronics
The PCM1602Y/2K can serve as the digital-to-analog stage in an active loudspeaker controller or multiway amplifier board that accepts I2S audio. Its six outputs permit three stereo groups to be converted before amplification and crossover processing. The 24-bit resolution and 192 kHz maximum rate support high-fidelity digital source signals, while the 48-LQFP package provides a defined surface-mount implementation. The designer must preserve analog return paths and implement the manufacturer’s required output filtering. For an 8-channel system, two six-channel converters may be needed, subject to valid clocking and channel-mapping requirements.
Được đề xuất
Digital Speaker and Amplifier System
The PCM1602Y/2K fits a digital speaker or networked-amplifier system that receives multichannel I2S audio and requires local analog conversion. Three stereo output groups can feed amplification and crossover stages from one converter, reducing package count compared with separate stereo devices. The 192 kHz sampling capability is useful when the upstream system transports high-rate audio, and the 24-bit resolution supports detailed signal reconstruction. Because the converter’s analog output is limited to 3.41 V, downstream amplifier gain must be selected accordingly. Validate the reference output network, channel mapping, and thermal performance of the complete amplifier board.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PCM1602Y/2K — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PCM1602APTR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) |
| Converter Type | Enhanced multilevel delta-sigma DAC | Enhanced multilevel delta-sigma DAC |
| Resolution | 24 bit | 24 bit |
| Output Channels | 6 channels | 6 channels |
| Maximum Sampling Rate | 192 kHz | 192 kHz |
| Digital Interface | I2S | I2S |
Bảo phân biệt quan trọng
- Six-channel integration in one converter (vsPCM1602APTR)
- Direct six-channel I2S audio conversion (vsPCM1602APTR)
- Defined 3.41 V analog-output boundary (vsPCM1602APTR)
- Defined nominal settling behavior (vsPCM1602APTR)
Ghi chú thiết kế
Place the PCM1602Y/2K analog-output network and its bypass components close to the converter pins, and route digital clock and data traces away from sensitive output nodes. Use the manufacturer’s reference layout to determine component placement and trace geometry for the 48-LQFP footprint. Continuous ground-plane construction is generally preferable to fragmented return paths because the device combines a high-speed digital interface with analog output stages.
Follow the manufacturer’s supply, bypass-capacitor, and power-sequence recommendations exactly. Decoupling components should be positioned at the relevant supply pins with short, direct connections so switching noise does not propagate into the converter’s analog outputs. Before finalizing amplifier gain or coupling networks, confirm that downstream circuitry remains compatible with the specified 3.41 V maximum analog output and the device’s actual output-swing conditions.
Do not treat PCM1602Y, PCM1602Y/2K, and PCM1602APTR as interchangeable solely because their product names are similar. Confirm the exact ordering suffix, pin functions, package, and interface configuration before releasing a purchase order or replacement. For an existing PCB, use the manufacturer’s pin-description table and application circuit rather than inferring connections from another package or ordering configuration.
Thông tin tuân thủ
No compliance declarations were identified in the retrieved product information. The component is an audio converter IC rather than an automotive-qualified device.