PEX8624-BB50RBIF - 24-Lane PCIe Gen 2 Switch | Broadcom
料号: PEX8624-BB50RBIF ✓ 量产中PEX8624-BB50RBIF 概述
A PCI Express switch is a multiport interface IC that connects one upstream host-facing port to multiple downstream ports. Within the PCI Express hierarchy, the PEX8624 belongs to the bridge and switch class of system interconnect devices. It routes ordered transaction layers between a root complex or another switch and attached endpoint devices, allowing storage, networking, accelerator, and capture cards to share a host PCIe slot.
The device provides 24 PCI Express lanes, six switch ports, and a 5.0 GT/s data rate. Its 324-FCBGA package uses a square 19 x 19 mm outline and a fine-pitch ball-grid layout. The high pin count reflects the simultaneous assignment of lane transmitters and receivers, auxiliary signaling, reference-clock connections, power rails, control interfaces, and configuration pins required by a multiport PCIe switch.
PEX8624-BB50RBIF is intended for Gen 2 designs rather than higher-speed Gen 3 or Gen 4 fabrics. At 5.0 GT/s, each lane carries one bit per transfer cycle before line coding and protocol overhead are considered. The six-port topology gives system architects a way to consolidate several PCIe endpoint connections behind a common upstream interface while maintaining deterministic peer-to-peer routing support.
Typical uses include PCIe expansion systems, industrial data-acquisition chassis, high-bandwidth network appliances, external storage controllers, test and measurement platforms, and GPU or FPGA accelerator systems. In these applications, the switch can reduce host-controller scarcity and provide a structured path between multiple endpoint types without redesigning the mechanical enclosure around several discrete adapters.
PCB implementation is the dominant engineering consideration. A 324-FCBGA device requires a fine-pitch land pattern, multilayer PCB construction, controlled impedance routing, solid reference planes, and careful power and ground-plane distribution. The differential PCIe pairs should be routed as length-matched transmission lines with minimal stubs and layer transitions, while the reference clock and PERST# sequencing require deliberate system-level planning.
This page consolidates the confirmed lane count, port count, transfer rate, package outline, sourcing constraints, and practical implementation considerations for PEX8624-BB50RBIF. For a new layout, use the Broadcom PEX8624 datasheet and reference design to validate the complete ball map, power architecture, clock topology, connector assignments, and PCIe training sequence before releasing fabrication files.
直接替换替代料: PEX8624-BB50RBIF ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PEX8624-BB50RBIF (相同外形与封装尺寸) ——差异在于 Temperature Grade.
PEX8624-BB50RBI-F
✅ 直接替换📋 参考替代料(不在目录中)
PEX8624-BB50RBI-G
✅ 直接替换📋 参考替代料(不在目录中)
PEX8624-BB50RBIF 最大额定值与电气特性
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2 |
| Maximum Data Rate | 5.0 GT/s |
| PCI Express Lane Count | 24 lanes |
| Switch Port Count | 6 ports |
| Package Type | 324-FCBGA |
| Package Body Size | 19 x 19 mm |
| Package Shape | Square |
| Terminal Form | Ball |
| Number of Terminals | 324 balls |
| 安装类型 | Surface mount |
| Temperature Grade | Industrial |
PEX8624-BB50RBIF square 引脚配置指南
PEX8624-BB50RBIF(square 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: PEX8624-BB50RBIF.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PEX8624-BB50RBIF 适用于 6 应用s: Industrial Data-Acquisition Systems, PCIe Expansion Enclosures, Network Appliances, External Storage Systems, GPU and FPGA Accelerator Systems, Test and Measurement Platforms.
Industrial Data-Acquisition Systems
The PEX8624-BB50RBIF fits industrial data-acquisition systems that must combine several PCIe acquisition, processing, and communication cards behind one host interface. Its 24 lanes can be distributed across six switch ports, while the 5.0 GT/s Gen 2 rate provides a defined performance ceiling for each active link. The six-port topology helps equipment designers avoid installing multiple root-complex resources when synchronized measurement or control traffic must reach several endpoints. The principal engineering cost is PCB complexity: a 324-FCBGA package requires fine-pitch routing, multilayer power distribution, and controlled-impedance differential pairs. Use the Broadcom reference layout to allocate lane widths, configure downstream links, and preserve clock and reset integrity.
推荐
PCIe Expansion Enclosures
The PEX8624-BB50RBIF is appropriate for a PCIe expansion enclosure that exposes multiple connector slots to a host computer. Six downstream ports can support accelerator, storage, network, and test cards, provided the 24 available lanes are distributed according to the intended link widths. At a maximum 5.0 GT/s, the device keeps the enclosure within PCIe Gen 2 capabilities and supports a more consolidated topology than separate host adapters. Thermal and mechanical design remain essential because a dense switching IC and several high-power endpoint cards can concentrate heat inside a compact enclosure. The 19 x 19 mm FCBGA also requires a multilayer motherboard with careful ball-escape routing and a ground-reference plane beneath the device.
推荐
Network Appliances
The PEX8624-BB50RBIF can support a network appliance that needs several PCIe-connection paths rather than a single endpoint link. Possible downstream functions include Ethernet controllers, NVMe storage, security or compression accelerators, and dedicated processing engines. The switch's 24-lane capacity allows a designer to balance link widths against endpoint count, avoiding the inefficiency of assigning every card a full x16 connection when only a subset requires that bandwidth. Because the device operates at PCIe Gen 2, designs must avoid assuming Gen 3 throughput from the shared host link. Thermal planning, reference-clock distribution, and deterministic PCIe reset sequencing should be developed alongside the PCB layout.
推荐
External Storage Systems
The PEX8624-BB50RBIF is well suited to storage appliances that aggregate multiple PCIe devices, such as NVMe controllers, RAID interface cards, or cache accelerators. Its six-port structure can reduce dependence on scarce host PCIe slots, while 24 lanes provide a practical pool for combining narrower storage links with one wider accelerator link. The switch does not change the underlying Gen 2 limit of 5.0 GT/s, so storage performance must be modeled per lane and per port. Firmware should also account for power-state transitions and coordinated reset behavior when multiple storage paths start or stop. The switch IC's high pin count makes uninterrupted power, reference clock, and ground distribution central to maintaining reliable link training.
推荐
GPU and FPGA Accelerator Systems
The PEX8624-BB50RBIF can be used in systems that connect FPGA-based processing modules or accelerator cards through PCIe. Twenty-four lanes are sufficient to combine several x4 or x8 endpoint links, allowing a host processor to access multiple isolated accelerators without assigning a dedicated root port to every board. The 5.0 GT/s Gen 2 ceiling is important when sizing data paths: sustained transfers must remain within the available per-lane bandwidth after protocol overhead. Accelerator systems may also create substantial simultaneous power and thermal loads, so the switch should not be treated as an isolated low-power interface IC. Signal-integrity work should focus on matched differential routing, solid plane returns, and clock jitter margins.
推荐
Test and Measurement Platforms
The PEX8624-BB50RBIF fits modular test and measurement platforms that connect acquisition engines, signal-processing boards, communication modules, and storage to a single host. Six ports provide a structured PCIe topology while the 24-lane budget permits flexible allocation among instruments with different bandwidth requirements. This arrangement can simplify chassis backplane design compared with assigning every module a separate host controller. A Gen 2 implementation remains appropriate when instrument data rates are well below the 5.0 GT/s per-lane ceiling and deterministic lane sharing is acceptable. The design must still preserve training margins through lossless transitions, controlled reference-clock distribution, and careful reset sequencing, while accounting for heat generated by the switch and adjacent instrumentation modules.
推荐
推荐产品汇总
工程参考数据: PEX8624-BB50RBIF ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PEX8624-BB50RBI-F | PEX8624-BB50RBI-G |
|---|---|---|---|
| Package | 324-FCBGA (19 x 19 mm) | 324-FCBGA (19 x 19 mm) | 324-FCBGA (19 x 19 mm) |
| Brand | Broadcom | Broadcom | Broadcom |
| Product Type | PCI Express switch IC | PCI Express switch IC | PCI Express switch IC |
| PCI Express Generation | Gen 2 | Gen 2 | Gen 2 |
| Maximum Data Rate | 5.0 GT/s | 5.0 GT/s | 5.0 GT/s |
| PCI Express Lane Count | 24 lanes | 24 lanes | 24 lanes |
| Switch Port Count | 6 ports | 6 ports | 6 ports |
| Number of Terminals | 324 balls | 324 balls | 324 balls |
关键差异点
- Consolidates multiple endpoints behind a six-port Gen 2 topology (对比 PEX8624-BB50RBI-G)
- Uses the same 324-FCBGA mechanical format as the directly indexed alternatives (对比 PEX8624-BB50RBI-F)
- Designed specifically for PCIe Gen 2 rather than newer fabric generations (对比 PEX8624-BB50RBI-G)
设计说明
Use the Broadcom PEX8624 reference layout to define the 324-FCBGA footprint and ball escape strategy. The 19 x 19 mm package has a dense ball pitch, so a two-layer escape is unlikely to provide practical routing for all PCIe lanes and power connections. A multilayer board with short high-speed escape paths, uninterrupted reference planes, and manufacturer-qualified via structures should be modeled and reviewed before schematic-to-layout release.
Route every PCI Express differential pair as a controlled-impedance transmission line with matched length within the tolerance defined by the Broadcom layout guidance. Avoid stubs, unnecessary layer changes, and splits beneath high-speed pairs. Pay particular attention to skew between transmit and receive halves of a lane, because a 5.0 GT/s interface still requires sufficient eye and timing margin after connector, package, and PCB losses are combined.
Separate the switch's core, I/O, and auxiliary supply requirements according to the manufacturer power tree, and verify local decoupling at the corresponding balls. Estimate the worst-case dissipation from total supply power, switching activity, and ambient temperature before selecting copper area or thermal solutions. The 324-ball package has many power and ground connections, so plane continuity and via stitching are as important as the quantity of individual capacitors.
Do not assume that the RBIF, RBI-F, and RBI-G ordering suffixes are interchangeable. Confirm the exact Broadcom ordering table, device revision, temperature grade, qualification status, clock configuration, and lifecycle status for the production build. Also avoid treating the 24-lane total as independently available on every port; link widths and usable lane allocation must match the selected switch configuration and endpoint capabilities.
合规信息
The Broadcom product family and industrial temperature grade are identified, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for this exact ordering code.