PEX8624-BB50RBIF - 24-Lane PCIe Gen 2 Switch | Broadcom
MPN: PEX8624-BB50RBIF ✓ فعالPEX8624-BB50RBIF نمای کلی
A PCI Express switch is a multiport interface IC that connects one upstream host-facing port to multiple downstream ports. Within the PCI Express hierarchy, the PEX8624 belongs to the bridge and switch class of system interconnect devices. It routes ordered transaction layers between a root complex or another switch and attached endpoint devices, allowing storage, networking, accelerator, and capture cards to share a host PCIe slot.
The device provides 24 PCI Express lanes, six switch ports, and a 5.0 GT/s data rate. Its 324-FCBGA package uses a square 19 x 19 mm outline and a fine-pitch ball-grid layout. The high pin count reflects the simultaneous assignment of lane transmitters and receivers, auxiliary signaling, reference-clock connections, power rails, control interfaces, and configuration pins required by a multiport PCIe switch.
PEX8624-BB50RBIF is intended for Gen 2 designs rather than higher-speed Gen 3 or Gen 4 fabrics. At 5.0 GT/s, each lane carries one bit per transfer cycle before line coding and protocol overhead are considered. The six-port topology gives system architects a way to consolidate several PCIe endpoint connections behind a common upstream interface while maintaining deterministic peer-to-peer routing support.
Typical uses include PCIe expansion systems, industrial data-acquisition chassis, high-bandwidth network appliances, external storage controllers, test and measurement platforms, and GPU or FPGA accelerator systems. In these applications, the switch can reduce host-controller scarcity and provide a structured path between multiple endpoint types without redesigning the mechanical enclosure around several discrete adapters.
PCB implementation is the dominant engineering consideration. A 324-FCBGA device requires a fine-pitch land pattern, multilayer PCB construction, controlled impedance routing, solid reference planes, and careful power and ground-plane distribution. The differential PCIe pairs should be routed as length-matched transmission lines with minimal stubs and layer transitions, while the reference clock and PERST# sequencing require deliberate system-level planning.
This page consolidates the confirmed lane count, port count, transfer rate, package outline, sourcing constraints, and practical implementation considerations for PEX8624-BB50RBIF. For a new layout, use the Broadcom PEX8624 datasheet and reference design to validate the complete ball map, power architecture, clock topology, connector assignments, and PCIe training sequence before releasing fabrication files.
جایگزینهای drop-in برای PEX8624-BB50RBIF — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای PEX8624-BB50RBIF (همان فرمفاکتور و فوتپرینت) — متفاوت در Temperature Grade.
PEX8624-BB50RBI-F
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PEX8624-BB50RBI-G
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
PEX8624-BB50RBIF حداکثر مقادیر مجاز و مشخصات الکتریکی
| Product Type | PCI Express switch IC |
| PCI Express Generation | Gen 2 |
| Maximum Data Rate | 5.0 GT/s |
| PCI Express Lane Count | 24 lanes |
| Switch Port Count | 6 ports |
| Package Type | 324-FCBGA |
| Package Body Size | 19 x 19 mm |
| Package Shape | Square |
| Terminal Form | Ball |
| Number of Terminals | 324 balls |
| نوع نصب | Surface mount |
| Temperature Grade | Industrial |
راهنمای پیکربندی پین PEX8624-BB50RBIF square
پیکربندی پین برای PEX8624-BB50RBIF (پکیج square). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای PEX8624-BB50RBIF.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
PEX8624-BB50RBIF مناسب است برای 6 کاربردs: Industrial Data-Acquisition Systems, PCIe Expansion Enclosures, Network Appliances, External Storage Systems, GPU and FPGA Accelerator Systems, Test and Measurement Platforms.
Industrial Data-Acquisition Systems
The PEX8624-BB50RBIF fits industrial data-acquisition systems that must combine several PCIe acquisition, processing, and communication cards behind one host interface. Its 24 lanes can be distributed across six switch ports, while the 5.0 GT/s Gen 2 rate provides a defined performance ceiling for each active link. The six-port topology helps equipment designers avoid installing multiple root-complex resources when synchronized measurement or control traffic must reach several endpoints. The principal engineering cost is PCB complexity: a 324-FCBGA package requires fine-pitch routing, multilayer power distribution, and controlled-impedance differential pairs. Use the Broadcom reference layout to allocate lane widths, configure downstream links, and preserve clock and reset integrity.
پیشنهادی
PCIe Expansion Enclosures
The PEX8624-BB50RBIF is appropriate for a PCIe expansion enclosure that exposes multiple connector slots to a host computer. Six downstream ports can support accelerator, storage, network, and test cards, provided the 24 available lanes are distributed according to the intended link widths. At a maximum 5.0 GT/s, the device keeps the enclosure within PCIe Gen 2 capabilities and supports a more consolidated topology than separate host adapters. Thermal and mechanical design remain essential because a dense switching IC and several high-power endpoint cards can concentrate heat inside a compact enclosure. The 19 x 19 mm FCBGA also requires a multilayer motherboard with careful ball-escape routing and a ground-reference plane beneath the device.
پیشنهادی
Network Appliances
The PEX8624-BB50RBIF can support a network appliance that needs several PCIe-connection paths rather than a single endpoint link. Possible downstream functions include Ethernet controllers, NVMe storage, security or compression accelerators, and dedicated processing engines. The switch's 24-lane capacity allows a designer to balance link widths against endpoint count, avoiding the inefficiency of assigning every card a full x16 connection when only a subset requires that bandwidth. Because the device operates at PCIe Gen 2, designs must avoid assuming Gen 3 throughput from the shared host link. Thermal planning, reference-clock distribution, and deterministic PCIe reset sequencing should be developed alongside the PCB layout.
پیشنهادی
External Storage Systems
The PEX8624-BB50RBIF is well suited to storage appliances that aggregate multiple PCIe devices, such as NVMe controllers, RAID interface cards, or cache accelerators. Its six-port structure can reduce dependence on scarce host PCIe slots, while 24 lanes provide a practical pool for combining narrower storage links with one wider accelerator link. The switch does not change the underlying Gen 2 limit of 5.0 GT/s, so storage performance must be modeled per lane and per port. Firmware should also account for power-state transitions and coordinated reset behavior when multiple storage paths start or stop. The switch IC's high pin count makes uninterrupted power, reference clock, and ground distribution central to maintaining reliable link training.
پیشنهادی
GPU and FPGA Accelerator Systems
The PEX8624-BB50RBIF can be used in systems that connect FPGA-based processing modules or accelerator cards through PCIe. Twenty-four lanes are sufficient to combine several x4 or x8 endpoint links, allowing a host processor to access multiple isolated accelerators without assigning a dedicated root port to every board. The 5.0 GT/s Gen 2 ceiling is important when sizing data paths: sustained transfers must remain within the available per-lane bandwidth after protocol overhead. Accelerator systems may also create substantial simultaneous power and thermal loads, so the switch should not be treated as an isolated low-power interface IC. Signal-integrity work should focus on matched differential routing, solid plane returns, and clock jitter margins.
پیشنهادی
Test and Measurement Platforms
The PEX8624-BB50RBIF fits modular test and measurement platforms that connect acquisition engines, signal-processing boards, communication modules, and storage to a single host. Six ports provide a structured PCIe topology while the 24-lane budget permits flexible allocation among instruments with different bandwidth requirements. This arrangement can simplify chassis backplane design compared with assigning every module a separate host controller. A Gen 2 implementation remains appropriate when instrument data rates are well below the 5.0 GT/s per-lane ceiling and deterministic lane sharing is acceptable. The design must still preserve training margins through lossless transitions, controlled reference-clock distribution, and careful reset sequencing, while accounting for heat generated by the switch and adjacent instrumentation modules.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای PEX8624-BB50RBIF — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | PEX8624-BB50RBI-F | PEX8624-BB50RBI-G |
|---|---|---|---|
| Package | 324-FCBGA (19 x 19 mm) | 324-FCBGA (19 x 19 mm) | 324-FCBGA (19 x 19 mm) |
| Brand | Broadcom | Broadcom | Broadcom |
| Product Type | PCI Express switch IC | PCI Express switch IC | PCI Express switch IC |
| PCI Express Generation | Gen 2 | Gen 2 | Gen 2 |
| Maximum Data Rate | 5.0 GT/s | 5.0 GT/s | 5.0 GT/s |
| PCI Express Lane Count | 24 lanes | 24 lanes | 24 lanes |
| Switch Port Count | 6 ports | 6 ports | 6 ports |
| Number of Terminals | 324 balls | 324 balls | 324 balls |
تفاوتهای کلیدی
- Consolidates multiple endpoints behind a six-port Gen 2 topology (در مقابلPEX8624-BB50RBI-G)
- Uses the same 324-FCBGA mechanical format as the directly indexed alternatives (در مقابلPEX8624-BB50RBI-F)
- Designed specifically for PCIe Gen 2 rather than newer fabric generations (در مقابلPEX8624-BB50RBI-G)
یادداشتهای طراحی
Use the Broadcom PEX8624 reference layout to define the 324-FCBGA footprint and ball escape strategy. The 19 x 19 mm package has a dense ball pitch, so a two-layer escape is unlikely to provide practical routing for all PCIe lanes and power connections. A multilayer board with short high-speed escape paths, uninterrupted reference planes, and manufacturer-qualified via structures should be modeled and reviewed before schematic-to-layout release.
Route every PCI Express differential pair as a controlled-impedance transmission line with matched length within the tolerance defined by the Broadcom layout guidance. Avoid stubs, unnecessary layer changes, and splits beneath high-speed pairs. Pay particular attention to skew between transmit and receive halves of a lane, because a 5.0 GT/s interface still requires sufficient eye and timing margin after connector, package, and PCB losses are combined.
Separate the switch's core, I/O, and auxiliary supply requirements according to the manufacturer power tree, and verify local decoupling at the corresponding balls. Estimate the worst-case dissipation from total supply power, switching activity, and ambient temperature before selecting copper area or thermal solutions. The 324-ball package has many power and ground connections, so plane continuity and via stitching are as important as the quantity of individual capacitors.
Do not assume that the RBIF, RBI-F, and RBI-G ordering suffixes are interchangeable. Confirm the exact Broadcom ordering table, device revision, temperature grade, qualification status, clock configuration, and lifecycle status for the production build. Also avoid treating the 24-lane total as independently available on every port; link widths and usable lane allocation must match the selected switch configuration and endpoint capabilities.
اطلاعات انطباق
The Broadcom product family and industrial temperature grade are identified, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for this exact ordering code.