PIC16C65A-20E/PQ - 8-bit 20MHz 7KB OTP MCU 44-MQFP | Microchip
料号： PIC16C65A-20E/PQ ✗ 停产| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $7.45 | $7.45 |
| 10 | $6.85 | $68.50 |
| 100 | $5.95 | $595.00 |
| 500 | $5.3 | $2,650.00 |
| 1,000 | $4.85 | $4,850.00 |
PIC16C65A-20E/PQ 概述
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (ROM/OTP/Flash), data memory (RAM), and peripherals such as timers, ADC, UART, and I/O ports. The PIC16CXX family uses a RISC Harvard architecture with a single accumulator (W register) and separate program and data buses, which allows simultaneous instruction fetch and data access. Microcontrollers sit within the broader hierarchy of microprocessors, embedded systems, and finally electronic control units - they are the computational core of nearly every modern embedded product.
Key features of the PIC16C65A-20E/PQ include a 20 MHz maximum clock rate, 13-bit instruction word, wide operating voltage range, and low-power consumption quoted at 15 uA typical at 5V/4 MHz and 1 uA typical at 3V/32 kHz. The 33 digital I/O pins support direct interfacing to switches, LEDs, sensors, and external peripherals, while on-chip peripherals include multiple timers, a synchronous/asynchronous serial port (USART), capture/compare/PWM modules, and parallel slave port functionality.
The PIC16C65A architecture is fully static, allowing the clock to be stopped without losing register state - useful for low-power sleep and wake-up designs. Its EPROM/ROM-based program memory offers one-time programmable (OTP) flexibility for prototyping and medium-volume production. The 'A' revision adds peripheral and memory enhancements over the original PIC16C65, making it suitable for applications requiring more interrupt sources and additional I/O compared to the PIC16C63 and PIC16C64.
Typical applications include industrial control systems, automotive body and chassis electronics, motor control, sensor interfacing, and consumer appliances. Its extended temperature grade and 33 I/O make it well-suited to harsh-environment embedded designs.
When designing with this device, note that OTP memory cannot be re-programmed in-circuit - confirm firmware before final programming. Use Microchip's MPASM/MPLAB toolchain for assembly development, and ensure in-circuit serial programming (ICSP) pins are brought out for production.
This page synthesizes distributor pricing, drop-in PIC16CXX alternatives, and practical design notes that go beyond the manufacturer datasheet to accelerate evaluation.
直接替换替代料： PIC16C65A-20E/PQ ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC16C65A-20E/PQ （相同外形与封装尺寸） ——差异在于 Package, Core Architecture, Program Memory Type, Program Memory Size, Timers.
快速对比工具——选择替代料号进行并排对比：
PIC16C65A-20/PQ
✅ 直接替换✓ 有现货
$4.61 / 个
查看数据手册 →PIC16C65A-10/PQ
✅ 直接替换✓ 有现货
$6.1 / 个
查看数据手册 →PIC16C64A-20/PQ
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$5.2 / 个
查看数据手册 →PIC16C65A-04/PQ
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$6.2 / 个
查看数据手册 →PIC16C65A-20E/PT
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$11.85 / 个
查看数据手册 →PIC16C65A-10E/PQ
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
$9.75 / 个
查看数据手册 →PIC16C65A-20E/PQ 最大额定值与电气特性
| Product Type | 8-bit Microcontroller (MCU) |
| Core Architecture | PIC16CXX RISC Harvard (8-bit) |
| Program Memory Size | 7 KB (4K x 14) OTP EPROM |
| RAM Size | 192 bytes |
| 最大时钟频率 | 20 MHz |
| I/O Pins | 33 |
| 封装 | 44-MQFP (10x10 mm) |
| Operating Voltage Range | 2.5 V to 6.0 V |
| 工作温度范围 | -40 C to +125 C (Extended, 'E') |
| Supply Current (5V, 4 MHz) | 15 uA typical |
| Supply Current (3V, 32 kHz) | 1 uA typical |
| Instruction Set | 35 instructions, 14-bit width |
| Timers | Multiple 8/16-bit timers |
| Communication Interfaces | USART/SCI, SPI, I2C (SSP), Parallel Slave Port |
| 安装类型 | Surface Mount (MQFP, Gull Wing) |
| RoHS 状态 | Compliant |
| AEC-Q100 | Not explicitly qualified (Automotive grade per temp range) |
PIC16C65A-20E/PQ 引脚配置
| 引脚 1 | OSC1/CLKIN — Oscillator input or external clock in |
| 引脚 2 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| 引脚 3 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| 引脚 4 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| 引脚 5 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / Vref |
| 引脚 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| 引脚 7 | RA5/SS/AN4 — PORTA bit 5 / SPI slave select / analog input 4 |
| 引脚 8 | VSS — Ground reference |
| 引脚 9 | OSC2/CLKOUT — Oscillator output / clock out |
| 引脚 10 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / clock in |
| 引脚 11 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| 引脚 12 | RC2/CCP1 — PORTC bit 2 / CCP1 PWM output |
| 引脚 13 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| 引脚 14 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| 引脚 15 | RC5/SDO — PORTC bit 5 / SPI data out |
| 引脚 16 | RC6/TX/CK — PORTC bit 6 / USART TX / clock |
| 引脚 17 | RC7/RX/DT — PORTC bit 7 / USART RX / data |
| 引脚 18 | VSS — Ground reference |
| 引脚 19 | RD0/PSP0 — PORTD bit 0 / parallel slave port bit 0 |
| 引脚 20 | RD1/PSP1 — PORTD bit 1 / parallel slave port bit 1 |
| 引脚 21 | RD2/PSP2 — PORTD bit 2 / parallel slave port bit 2 |
| 引脚 22 | RD3/PSP3 — PORTD bit 3 / parallel slave port bit 3 |
| 引脚 23 | RC4 (Note: alternate) — Per datasheet - see errata if applicable |
| 引脚 24 | RD4/PSP4 — PORTD bit 4 / parallel slave port bit 4 |
| 引脚 25 | RD5/PSP5 — PORTD bit 5 / parallel slave port bit 5 |
| 引脚 26 | RD6/PSP6 — PORTD bit 6 / parallel slave port bit 6 |
| 引脚 27 | RD7/PSP7 — PORTD bit 7 / parallel slave port bit 7 |
| 引脚 28 | VSS — Ground reference |
| 引脚 29 | RE0/RD/AN5 — PORTE bit 0 / read control / analog input 5 |
| 引脚 30 | RE1/WR/AN6 — PORTE bit 1 / write control / analog input 6 |
| 引脚 31 | RE2/CS/AN7 — PORTE bit 2 / chip select / analog input 7 |
| 引脚 32 | VDD — Positive supply voltage |
| 引脚 33 | RB0/INT — PORTB bit 0 / external interrupt |
| 引脚 34 | RB1 — PORTB bit 1 |
| 引脚 35 | RB2 — PORTB bit 2 |
| 引脚 36 | RB3 — PORTB bit 3 |
| 引脚 37 | RB4 — PORTB bit 4 |
| 引脚 38 | RB5 — PORTB bit 5 |
| 引脚 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| 引脚 40 | RB7/PGD — PORTB bit 7 / ICSP data |
| 引脚 41 | VSS — Ground reference |
| 引脚 42 | VDD — Positive supply voltage |
| 引脚 43 | VDD — Positive supply voltage |
| 引脚 44 | MCLR/VPP — Master clear / programming voltage |
典型应用
PIC16C65A-20E/PQ 适用于 6 应用s: Industrial Motor Control, Automotive Body Electronics, Sensor Interface and Data Acquisition, Consumer Appliance Control, HVAC and Building Automation, Security and Access Control Panels.
Industrial Motor Control
The PIC16C65A-20E/PQ fits industrial motor control applications because its 20 MHz clock and 33 I/O pins provide sufficient throughput to handle PWM generation, quadrature encoder feedback, and closed-loop control of small DC or stepper motors. The capture/compare/PWM modules on board generate the switching waveforms needed for variable-speed drives, while the 192 B RAM supports modest PID controller state. Its -40C to +125C extended temperature range allows deployment near motor housings where ambient temperatures rise. The 7KB OTP program memory holds a complete motion control firmware image including trapezoidal profiles and current-limit routines. Placed on a 44-MQFP carrier board with isolated gate drivers, this MCU drives three-phase inverter stages up to a few hundred watts without DSP hardware.
推荐
Automotive Body Electronics
The PIC16C65A-20E/PQ is well-suited to automotive body modules such as central locking, mirror control, and lighting controllers because its AUTOMOTIVE temperature grade (-40C to +125C) and 33 I/O lines handle multiple switch inputs and relay outputs simultaneously. The on-chip USART enables LIN or K-line communication with body control networks, while the parallel slave port allows connection to a dashboard master MCU. OTP memory is acceptable for body modules where firmware is stable and code protection is desired. With proper reverse-battery and load-dump protection on the supply pin, this MCU reliably drives automotive-grade relays and solenoids in a 44-MQFP footprint suited to under-dash PCB assemblies.
推荐
Sensor Interface and Data Acquisition
For multi-channel sensor interface boards, the PIC16C65A-20E/PQ's 33 I/O pins read multiple digital sensors (Hall-effect, optical encoders, switches) and drive indicator LEDs without external I/O expanders. Its USART and SSP peripherals stream sensor data to a host processor or display, while timers handle precise sampling intervals. The 192 B RAM buffers short data packets before transmission. Operating from 3V or 5V supplies, the MCU interfaces directly to 5V logic sensors with no level shifters, simplifying PCB layout in the 44-MQFP package.
推荐
Consumer Appliance Control
Washing machines, dishwashers, and microwave ovens benefit from the PIC16C65A-20E/PQ's combination of 33 I/O for keypad/scanner interfaces, multiple timers for wash-cycle sequencing, and OTP memory for low-cost mass production. The Extended temperature grade survives the heat of a closed appliance chassis, while the 20 MHz instruction rate drives both the user-interface scan and the motor-control loop. Its low-power modes (1 uA typical at 3V/32 kHz standby) reduce standby power for energy-star appliances.
推荐
HVAC and Building Automation
The PIC16C65A-20E/PQ is deployed in HVAC damper actuators, thermostat base stations, and zone controllers where its automotive-grade temperature tolerance handles attic and rooftop enclosures. The 33 I/O read multiple thermistor inputs and drive triac outputs for fan-speed control, while the USART links to a building automation bus. Its 7KB OTP holds zoning logic and PID control firmware, and the 44-MQFP package simplifies PCB layout with adequate creepage for line-voltage isolation.
推荐
Security and Access Control Panels
Alarm panels, access controllers, and intercom stations leverage the PIC16C65A-20E/PQ's 33 I/O to scan multiple keypads and door sensors while driving sirens and indicator LEDs. The Extended temperature grade accommodates outdoor or unconditioned installations, and the OTP memory prevents firmware tampering in security applications. The on-chip USART connects to a central monitoring station over a dial-up or GSM modem, while timers debounce mechanical inputs.
推荐
推荐产品汇总
工程参考数据： PIC16C65A-20E/PQ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC16C65A-20/PQ | PIC16C65A-10/PQ | PIC16C64A-20/PQ | PIC16C65A-04/PQ |
|---|---|---|---|---|---|
| Package | 44-MQFP (10x10) | 44-MQFP (10x10) - same | 44-MQFP (10x10) - same | 44-MQFP (10x10) - same | 44-MQFP (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 7 KB OTP | 7 KB OTP | 7 KB OTP | 4 KB OTP | 7 KB OTP |
| Maximum Clock | 20 MHz | 20 MHz | 10 MHz | 20 MHz | 4 MHz |
| Temperature Grade | Extended (-40C to +125C) | Commercial (0C to +70C) | Commercial (0C to +70C) | Commercial (0C to +70C) | Commercial (0C to +70C) |
| I/O Pins | 33 | 33 | 33 | 33 | 33 |
| RAM | 192 B | 192 B | 192 B | 128 B | 192 B |
| Approx Unit Price (qty 1) | $7.45 | $5.99 (LCSC) | lower (slower grade) | lower (less memory) | lower (slower grade) |
关键差异点
- Extended automotive-grade temperature range in same 44-MQFP package （对比 PIC16C65A-20/PQ)
- 20 MHz clock speed with full 7 KB OTP memory （对比 PIC16C65A-04/PQ)
- Higher memory density than the PIC16C64A in pin-compatible 44-MQFP （对比 PIC16C64A-20/PQ)
设计说明
Decouple VDD with a 100 nF ceramic capacitor placed within 5 mm of each VDD pin (the 44-MQFP has three VDD pins at 32, 42, 43). Add a bulk 10 uF tantalum or ceramic capacitor at the supply entry point. The PIC16C65A-20E/PQ draws approximately 15 mA at 20 MHz / 5V during active execution, so a linear regulator with at least 100 mA headroom is recommended for noise immunity.
Keep the MCLR/VPP pin trace short and route RB6/PGC and RB7/PGD to a programming header. The 44-MQFP footprint has fine-pitch 0.8 mm gull-wing leads - use a 0.4 mm stencil aperture and reflow profile per J-STD-020. Provide a 4-layer PCB with continuous ground plane under the IC to reduce EMI on the 33 I/O lines.
OTP memory is one-time programmable and cannot be re-flashed after programming - verify firmware with engineering samples (UV-erasable windowed parts) before committing to the production OTP device. The 'E' suffix denotes extended temperature grade (-40C to +125C); do NOT substitute 'E' parts into designs certified only for commercial range, and vice versa, without re-qualifying temperature performance.
When using the parallel slave port (PORTD with PORTE control signals), ensure the host bus driver has adequate drive strength to overcome PORTD's weak pull-ups. Add 10 kohm pull-ups on RE0/RE1/RE2 only if the host bus does not actively drive these lines during reset. For USART communication at 20 MHz clock with 115200 baud, the bit-time error is <2% - safe for reliable asynchronous serial links.
合规信息
RoHS compliant per Microchip product page. AUTOMOTIVE temperature grade per Partstack listing, but explicit AEC-Q100 qualification should be confirmed with Microchip for specific automotive programs. Lifecycle status is NRND - plan migration to flash-based PIC18F equivalents.
