PIC32MM0064GPL036T-I/MV - 32-bit 25MHz 64KB Flash MCU | Microchip
料号： PIC32MM0064GPL036T-I/MV ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $2.18 | $2.18 |
| 10 | $1.96 | $19.60 |
| 100 | $1.62 | $162.00 |
| 500 | $1.38 | $690.00 |
| 1,000 | $1.12 | $1,120.00 |
| 3,000 | $0.96 | $2,880.00 |
PIC32MM0064GPL036T-I/MV 概述
An MCU (microcontroller unit) is a single-chip computer that combines a CPU core, non-volatile program memory, working RAM, and a mix of analog/digital peripherals on one die. The PIC32MM0064GPL036T-I/MV belongs to the 32-bit MCU tier (MIPS32 architecture), more capable than 8/16-bit MCUs in DSP and code density, but more power-efficient than application processors. Within Microchip's portfolio, the PIC32MM GPL family sits between the PIC24/dsPIC33 16-bit line and the higher-end PIC32MX/MK families, optimized for cost-sensitive low-power applications.
Key specifications include a 2.0V to 3.6V operating voltage range, 25 MHz maximum core clock, 64 KB Flash (64K x 8), 8 KB SRAM, four 16-bit timers, two I2C, two SPI, and up to two UART interfaces, plus a 12-bit ADC with up to 200 ksps conversion rate and multiple 10-bit PWM outputs. The on-chip 32 kHz low-power oscillator and wide operating temperature range (-40C to +125C) further reinforce its fitness for industrial, IoT, and consumer products.
The microAptiv UC core implements the MIPS32 instruction set with hardware multiply/divide and a 5-stage pipeline that balances deterministic interrupt response with energy efficiency. Combined with Microchip's peripheral remapping architecture (PPS-like flexible pin assignment), designers gain layout freedom on dense boards while keeping firmware modular and reusable across the PIC32MM family.
Typical applications include IoT sensor nodes, battery-powered wearables, low-cost motor control loops, home automation controllers, and industrial sensor hubs. The 25 MHz core with 64 KB Flash easily accommodates connectivity stacks (BLE, LoRa, sub-GHz proprietary), sensor fusion routines, and small TFT GUIs without external memory.
A core design consideration is PCB layout: the UQFN-40 EP package requires a properly stitched ground pad and thermal vias for heat removal at high CPU loads. Decoupling should follow Microchip's guideline - one 100 nF ceramic per VDD pin plus a bulk 10 uF near the regulator - to keep core supply noise below the core's brown-out threshold.
This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC32MM family, and practical design notes that go beyond the manufacturer datasheet, giving procurement and engineering teams a single decision-ready reference.
直接替换替代料： PIC32MM0064GPL036T-I/MV ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： PIC32MM0064GPL036T-I/MV （相同外形与封装尺寸） ——差异在于 Core Architecture, Package, Timers, ADC, I/O Pins.
快速对比工具——选择替代料号进行并排对比：
PIC32MM0064GPL036-I/MV
✅ 直接替换📋 参考替代料（不在目录中）
PIC32MM0064GPL036-I/MVVAO
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
PIC32MM0064GPL028-I/ML
✅ 直接替换✓ 有现货
$2.25 / 个
查看数据手册 →PIC32MM0032GPL036-E/MV
✅ 直接替换✓ 有现货
$1.21 / 个
查看数据手册 →PIC32MM0064GPM036-I/MV
✅ 直接替换📋 参考替代料（不在目录中）
PIC32MM0064GPL036T-I/MV 最大额定值与电气特性
| Core Architecture | MIPS32 microAptiv UC |
| Core Bit Width | 32-bit |
| Maximum CPU Frequency | 25 MHz |
| Program Memory (Flash) | 64 KB (64K x 8) |
| Data Memory (SRAM) | 8 KB |
| Operating Voltage Range | 2.0 V to 3.6 V |
| 工作温度范围 | -40 C to +125 C |
| 封装 | 40-UQFN (5x5 mm) with exposed pad |
| I/O Pins | 29 |
| ADC | 12-bit, up to 200 ksps |
| Timers | 4 x 16-bit |
| Serial Interfaces | 2x I2C, 2x SPI, 2x UART |
| PWM Outputs | Multiple 10-bit PWM channels |
| Low-Power Feature | XLP with deep-sleep current down to ~500 nA |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
PIC32MM0064GPL036T-I/MV 引脚配置
| 引脚 1 | RB0 — I/O port B, bit 0 (with PPS) |
| 引脚 2 | RB1 — I/O port B, bit 1 (with PPS) |
| 引脚 3 | RB2 — I/O port B, bit 2 (with PPS) |
| 引脚 4 | RB3 — I/O port B, bit 3 (with PPS) |
| 引脚 5 |
典型应用
PIC32MM0064GPL036T-I/MV 适用于 6 应用s: IoT Wireless Sensor Nodes, Battery-Powered Wearable Devices, Low-Cost Motor Control (BLDC / FOC), Home Automation / Smart Home Hubs, Industrial Sensor Hubs, Low-Cost Consumer Electronics.
IoT Wireless Sensor Nodes
The PIC32MM0064GPL036T-I/MV fits IoT wireless sensor nodes because its 25 MHz MIPS32 microAptiv UC core, 64 KB Flash and 8 KB SRAM comfortably host BLE or Sub-GHz proprietary stacks while XLP technology drops quiescent current to roughly 500 nA in deep sleep. The 2.0-3.6 V single-rail supply directly accepts 2x AA or coin cells without a boost converter, and the 12-bit ADC with 200 ksps rate is well matched to common temperature, humidity, and gas sensor outputs. Used as the central MCU between a sensor front-end and a low-power radio, it delivers years of battery life while keeping the BOM lean. Trade-off: the GPL family has no USB, so commissioning is over UART or SWD only.
推荐
Battery-Powered Wearable Devices
Wearables benefit from the PIC32MM0064GPL036T-I/MV's sub-microamp deep-sleep current and 2.0-3.6 V supply, which let it run for weeks on a small Li-ion cell driving sensors and a small OLED. The 64 KB Flash holds RTOS kernels plus BLE stacks and gesture-detection firmware, while the 12-bit ADC reads heart-rate or motion signals at up to 200 ksps with hardware averaging for noise reduction. PPS-style peripheral remapping makes it easy to route I2C, SPI, and PWM onto the few remaining pins inside a small wearable enclosure. Compared to ARM Cortex-M0+ parts, the GPL gives comparable MIPS-per-milliwatt with Microchip's mature MPLAB X toolchain.
推荐
Low-Cost Motor Control (BLDC / FOC)
The PIC32MM0064GPL036T-I/MV drives low-power BLDC or small stepper motors thanks to its 25 MHz core, multiple 10-bit PWM channels, and 4 x 16-bit timers that handle center-aligned complementary PWM with dead-time insertion. With 64 KB Flash it fits sensorless or Hall-sensor FOC reference firmware from Microchip's AN1078 family without resorting to larger PIC32MX devices. The 40-UQFN package exposes enough I/O for three-phase gate drivers, fault inputs, and back-EMF sensing through the 12-bit ADC. For cost-sensitive ceiling fans, pumps, and small drones, this MCU delivers the right balance of performance and BOM cost.
推荐
Home Automation / Smart Home Hubs
Smart-home sensor and actuator hubs benefit from the PIC32MM0064GPL036T-I/MV's mix of 2x I2C, 2x SPI, and 2x UART channels, which let one MCU coordinate multiple radios, sensors, and relay drivers on a single PCB. The 25 MHz core executes Zigbee or Thread-style mesh stacks alongside local control logic, and 64 KB Flash leaves room for secure bootloaders and OTA update partitions. Industrial temperature range -40 C to +125 C supports deployment in unheated attics, garages, and outdoor enclosures. Its XLP sleep current extends battery life for wirelessly-powered push-buttons and door sensors that must run for years.
推荐
Industrial Sensor Hubs
Industrial sensor hubs use the PIC32MM0064GPL036T-I/MV because its -40 C to +125 C rating and 2.0-3.6 V supply tolerate factory-floor transients and 24 V-to-3.3 V regulator rails with margin. The 12-bit ADC at 200 ksps aggregates readings from multiple 4-20 mA loop sensors through external signal conditioning, while the 4 x 16-bit timers handle pulse counting for flow meters and encoders. 64 KB Flash is enough for Modbus RTU slave firmware plus diagnostic logging. Designers often pair this MCU with a small isolation barrier (digital isolator or RS-485 transceiver) to meet IEC 61131-2 industrial requirements.
推荐
Low-Cost Consumer Electronics
Mass-market consumer products - remote controls, small appliances, toys, and personal care devices - rely on the PIC32MM0064GPL036T-I/MV for its sub-$1 price at volume combined with real 32-bit performance. The 64 KB Flash accommodates capacitive-touch libraries and small graphics firmwares, while the 10-bit PWM channels drive LEDs, buzzers, and small DC loads without extra driver ICs. Deep-sleep currents near 500 nA let battery-powered devices sit on a shelf for a year or more without replacement. The 40-UQFN 5x5 mm footprint fits inside enclosures as small as a TV remote or an electric toothbrush.
推荐
推荐产品汇总
工程参考数据： PIC32MM0064GPL036T-I/MV ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC32MM0064GPL036-I/MV | PIC32MM0032GPL036-E/MV | PIC32MM0064GPM036-I/MV | PIC32MM0064GPL028-I/ML |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-UQFN (5x5) | 40-UQFN (5x5) - same | 40-UQFN (5x5) - same | 40-UQFN (5x5) - same | 28-QFN (6x6) - different but PPS-compatible |
| Core / Max Frequency | MIPS32 microAptiv UC / 25 MHz | MIPS32 microAptiv UC / 25 MHz | MIPS32 microAptiv UC / 25 MHz | MIPS32 microAptiv UC / 25 MHz | MIPS32 microAptiv UC / 25 MHz |
| Flash | 64 KB | 64 KB | 32 KB (-50%) | 64 KB | 28 KB (-56%) |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 4 KB |
| USB | No | No | No | Yes (USB 2.0 FS) | No |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Temperature Grade | -40 C to +125 C (industrial) | -40 C to +85 C | -40 C to +125 C (extended) | -40 C to +85 C | -40 C to +85 C |
| Approx Unit Price (qty-1) | $2.18 | $2.10 (tray form) | $1.95 | $2.45 (USB adds cost) | $1.80 |
关键差异点
- Lowest-cost 32-bit XLP option in the PIC32MM family with 64 KB Flash in 40-UQFN （对比 PIC32MM0064GPM036-I/MV)
- Industrial temperature grade in T&R packaging （对比 PIC32MM0064GPL036-I/MV (tray))
- 64 KB Flash at 25 MHz vs 16-bit PIC24F at the same price （对比 PIC24HJ64GP502-I/SO)
设计说明
Estimated: the 40-UQFN exposed pad must be soldered to a continuous ground copper pour with at least 4 thermal vias (0.3 mm drill, 0.5 mm pitch) under the EP for proper thermal and electrical performance. Place a 100 nF X7R ceramic decoupling capacitor on every VDD pin within 2 mm, plus one bulk 10 uF ceramic near the 3.3 V regulator. Keep the ICSP PGECx/PGEDx traces shorter than 50 mm and away from switching nodes to preserve clean in-circuit programming.
Estimated: at 25 MHz and 3.3 V with all peripherals active, the PIC32MM0064GPL036T-I/MV draws roughly 8-10 mA, so a 3.3 V LDO rated for at least 50 mA with 100 mV dropout at 10 mA (e.g., MCP1700) is recommended. For battery-powered designs, switch the MCU core clock to the internal 8 MHz oscillator before sleep and gate peripheral power domains through MOSFETs to push quiescent current toward the 500 nA deep-sleep spec.
Do not assume every PIC32MM GPL variant has the same peripheral mix - the 036 suffix carries 64 KB Flash while 028/020 shrink Flash and pin count. Brown-out resets must be enabled and the BOR voltage set to match the minimum operating rail (2.0 V); otherwise, voltage dips during TX bursts can corrupt Flash or freeze the CPU. When migrating from PIC24/dsPIC33, verify that PPS assignments are re-mapped, since pin function registers are not bit-compatible across families.
合规信息
RoHS and REACH compliance per Microchip PIC32MM product page. Industrial -40 C to +125 C grade (no AEC-Q100); choose PIC32MMxxxGPM family variants for AEC-Q100 qualified automotive designs.
