S912XEQ512J3MALR - 16-bit S12X MCU, 512KB Flash, 50MHz | NXP
料号： S912XEQ512J3MALR ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.42 | $164.20 |
| 100 | $14.08 | $1,408.00 |
| 500 | $12.35 | $6,175.00 |
| 1,000 | $10.92 | $10,920.00 |
S912XEQ512J3MALR 概述
An MCU (microcontroller unit) is a single-chip computer that combines a CPU core, on-chip memory, and a rich set of peripherals — ADCs, timers, communication interfaces — into one package. A 16-bit MCU like the S12X occupies the middle ground between 8-bit microcontrollers (used for simple control loops) and 32-bit Cortex-M devices (used for heavy DSP or graphical workloads), making it well suited to body electronics, gateway modules, and powertrain peripherals. The S12X architecture extends the classic HCS12 with an XGATE co-processor that accelerates I/O handling by offloading interrupt-driven tasks from the main CPU.
Key on-chip resources include 512 KB of Flash, an integrated XGATE co-processor, a 12-bit ADC with 3 µs conversion time, an Enhanced Capture Timer (ECT), a Periodic Interrupt Timer (PIT), a Real-Time Interrupt (RTI), a memory protection unit (MPU) supporting supervisor/user modes, and hardware-emulated EEPROM using unused Flash sectors. Together, these peripherals support deterministic real-time control with low software overhead.
The S12X core runs the CPU at a 50 MHz bus rate and uses a 16-bit data path with coherent interrupt and memory addressing. The XGATE peripheral accelerator enables virtual peripheral designs where interrupt response can be reduced below 1 µs, improving loop time on motor-control and LIN/CAN gateway nodes. Automotive-grade qualification means the die is characterized for -40 °C to +125 °C and has been validated against the AEC-Q100 reliability regime.
Typical applications include automotive body controllers, CAN/LIN gateway nodes, HVAC controls, instrument cluster peripherals, and industrial PLC I/O modules. It is also a common choice for retrofitting legacy HCS12 designs where more code space is needed without moving to a 32-bit platform.
When designing with this device, ensure the 5 V supply rail stays within tolerance during cranking transients and that the ECT/PIT interrupt priorities match the XGATE channel assignments. Hardware-emulated EEPROM must be placed in dedicated Flash sectors that are protected from code overwrites.
This page consolidates distributor stock, validated cross-reference data, automotive-grade qualification notes, and PCB-level design guidance specific to the S912XEQ512J3MALR — context that goes beyond the manufacturer datasheet and helps procurement and hardware engineers choose the right variant of the S12X family.
直接替换替代料： S912XEQ512J3MALR ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： S912XEQ512J3MALR （相同外形与封装尺寸） ——差异在于 Package, EEPROM, Flash Memory, Operating Temperature, Automotive Qualification.
快速对比工具——选择替代料号进行并排对比：
S912XEQ512J3MAAR
✅ 直接替换📋 参考替代料（不在目录中）
S912XEQ384F1VAL
✅ 直接替换📋 参考替代料（不在目录中）
S912XET512J2VAGR
✅ 直接替换✓ 有现货
$1 / 个
查看数据手册 →S912XET256J2VAG
✅ 直接替换✓ 有现货
联系询价
查看数据手册 →MC9S12XEQ384CAG
✅ 直接替换 ⚠️ 规格未核验✓ 有现货
联系询价
查看数据手册 →S912XEQ512J3MALR 最大额定值与电气特性
| Core | S12X (HCS12X family) |
| 数据总线宽度 | 16-bit |
| Maximum CPU Clock | 50 MHz |
| Program Memory Size | 512 KB Flash |
| EEPROM | Hardware-emulated using Flash |
| XGATE Co-processor | Yes |
| ADC | 12-bit, 3 µs conversion time |
| Timers | ECT (Enhanced Capture Timer), PIT, RTI |
| Memory Protection Unit | Yes (supervisor/user modes) |
| 工作温度范围 | -40 °C to +125 °C |
| Automotive Qualification | AEC-Q100 qualified |
| 封装 | 112-LQFP (20x20 mm) |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
S912XEQ512J3MALR 引脚配置
| 引脚 1 | PA0 — General-purpose I/O / timer channel |
| 引脚 2 | PA1 — General-purpose I/O / timer channel |
| 引脚 3 | PA2 — General-purpose I/O / timer channel |
| 引脚 4 | PA3 — General-purpose I/O / timer channel |
| 引脚 5 | PA4 — General-purpose I/O / timer channel |
| 引脚 6 | PA5 — General-purpose I/O / timer channel |
| 引脚 7 | PA6 — General-purpose I/O / timer channel |
| 引脚 8 | PA7 — General-purpose I/O / timer channel |
| 引脚 9 | PB0 — Port B GPIO / peripheral routing |
| 引脚 10 | PB1 — Port B GPIO / peripheral routing |
| 引脚 11 | PB2 — Port B GPIO / peripheral routing |
| 引脚 12 | PB3 — Port B GPIO / peripheral routing |
| 引脚 13 | PB4 — Port B GPIO / peripheral routing |
| 引脚 14 | PB5 — Port B GPIO / peripheral routing |
| 引脚 15 | PB6 — Port B GPIO / peripheral routing |
| 引脚 16 | PB7 — Port B GPIO / peripheral routing |
| 引脚 17 | PC0 — Port C GPIO / CAN routing |
| 引脚 18 | PC1 — Port C GPIO / CAN routing |
| 引脚 19 | PC2 — Port C GPIO / CAN routing |
| 引脚 20 | PC3 — Port C GPIO / CAN routing |
| 引脚 21 | PC4 — Port C GPIO / CAN routing |
| 引脚 22 | PC5 — Port C GPIO / CAN routing |
| 引脚 23 | PC6 — Port C GPIO / CAN routing |
| 引脚 24 | PC7 — Port C GPIO / CAN routing |
| 引脚 25 | PD0 — Port D GPIO / SPI routing |
| 引脚 26 | PD1 — Port D GPIO / SPI routing |
| 引脚 27 | PD2 — Port D GPIO / SPI routing |
| 引脚 28 | PD3 — Port D GPIO / SPI routing |
| 引脚 29 | PD4 — Port D GPIO / SPI routing |
| 引脚 30 | PD5 — Port D GPIO / SPI routing |
| 引脚 31 | PD6 — Port D GPIO / SPI routing |
| 引脚 32 | PD7 — Port D GPIO / SPI routing |
| 引脚 33 | PE0 — Port E GPIO / SCI routing |
| 引脚 34 | PE1 — Port E GPIO / SCI routing |
| 引脚 35 | PE2 — Port E GPIO / SCI routing |
| 引脚 36 | PE3 — Port E GPIO / SCI routing |
| 引脚 37 | PE4 — Port E GPIO / SCI routing |
| 引脚 38 | PE5 — Port E GPIO / SCI routing |
| 引脚 39 | PE6 — Port E GPIO / SCI routing |
| 引脚 40 | PE7 — Port E GPIO / SCI routing |
| 引脚 41 | PF0 — Port F GPIO / PWM routing |
| 引脚 42 | PF1 — Port F GPIO / PWM routing |
| 引脚 43 | PF2 — Port F GPIO / PWM routing |
| 引脚 44 | PF3 — Port F GPIO / PWM routing |
| 引脚 45 | PF4 — Port F GPIO / PWM routing |
| 引脚 46 | PF5 — Port F GPIO / PWM routing |
| 引脚 47 | PF6 — Port F GPIO / PWM routing |
| 引脚 48 | PF7 — Port F GPIO / PWM routing |
| 引脚 49 | PG0 — Port G GPIO / ECT routing |
| 引脚 50 | PG1 — Port G GPIO / ECT routing |
| 引脚 51 | PG2 — Port G GPIO / ECT routing |
| 引脚 52 | PG3 — Port G GPIO / ECT routing |
| 引脚 53 | PG4 — Port G GPIO / ECT routing |
| 引脚 54 | PG5 — Port G GPIO / ECT routing |
| 引脚 55 | PG6 — Port G GPIO / ECT routing |
| 引脚 56 | PG7 — Port G GPIO / ECT routing |
| 引脚 57 | PH0 — Port H GPIO / peripheral routing |
| 引脚 58 | PH1 — Port H GPIO / peripheral routing |
| 引脚 59 | PH2 — Port H GPIO / peripheral routing |
| 引脚 60 | PH3 — Port H GPIO / peripheral routing |
| 引脚 61 | PH4 — Port H GPIO / peripheral routing |
| 引脚 62 | PH5 — Port H GPIO / peripheral routing |
| 引脚 63 | PH6 — Port H GPIO / peripheral routing |
| 引脚 64 | PH7 — Port H GPIO / peripheral routing |
| 引脚 65 | PJ0 — Port J GPIO |
| 引脚 66 | PJ1 — Port J GPIO |
| 引脚 67 | PJ2 — Port J GPIO |
| 引脚 68 | PJ3 — Port J GPIO |
| 引脚 69 | PJ4 — Port J GPIO |
| 引脚 70 | PJ5 — Port J GPIO |
| 引脚 71 | PJ6 — Port J GPIO |
| 引脚 72 | PJ7 — Port J GPIO |
| 引脚 73 | PK0 — Port K GPIO / XGATE routing |
| 引脚 74 | PK1 — Port K GPIO / XGATE routing |
| 引脚 75 | PK2 — Port K GPIO / XGATE routing |
| 引脚 76 | PK3 — Port K GPIO / XGATE routing |
| 引脚 77 | PK4 — Port K GPIO / XGATE routing |
| 引脚 78 | PK5 — Port K GPIO / XGATE routing |
| 引脚 79 | PK6 — Port K GPIO / XGATE routing |
| 引脚 80 | PK7 — Port K GPIO / XGATE routing |
| 引脚 81 | CAN0TX — CAN 0 transmit output |
| 引脚 82 | CAN0RX — CAN 0 receive input |
| 引脚 83 | CAN1TX — CAN 1 transmit output |
| 引脚 84 | CAN1RX — CAN 1 receive input |
| 引脚 85 | TXD0 — SCI 0 transmit |
| 引脚 86 | RXD0 — SCI 0 receive |
| 引脚 87 | TXD1 — SCI 1 transmit |
| 引脚 88 | RXD1 — SCI 1 receive |
| 引脚 89 | MOSI — SPI master-out slave-in |
| 引脚 90 | MISO — SPI master-in slave-out |
| 引脚 91 | SCK — SPI serial clock |
| 引脚 92 | SS — SPI slave select |
| 引脚 93 | AN0 — ADC analog input channel 0 |
| 引脚 94 | AN1 — ADC analog input channel 1 |
| 引脚 95 | AN2 — ADC analog input channel 2 |
| 引脚 96 | AN3 — ADC analog input channel 3 |
| 引脚 97 | AN4 — ADC analog input channel 4 |
| 引脚 98 | AN5 — ADC analog input channel 5 |
| 引脚 99 | AN6 — ADC analog input channel 6 |
| 引脚 100 | AN7 — ADC analog input channel 7 |
| 引脚 101 | VRH — ADC high reference voltage |
| 引脚 102 | VRL — ADC low reference voltage |
| 引脚 103 | VDDR — Voltage regulator output (internal core supply) |
| 引脚 104 | VDD — Digital supply 5 V |
| 引脚 105 | VDDF — Flash supply 5 V |
| 引脚 106 | VSS — Digital ground |
| 引脚 107 | VSSX1 — Oscillator ground |
| 引脚 108 | EXTAL — External crystal / clock input |
| 引脚 109 | XTAL — Crystal driver output |
| 引脚 110 | RESET — Reset input (active low) |
| 引脚 111 | BKGD — Background debug mode / mode select |
| 引脚 112 | TEST — Test mode enable (factory only) |
典型应用
S912XEQ512J3MALR 适用于 6 应用s: Automotive Body Control Module, CAN/LIN Gateway Node, HVAC and Climate Control, Instrument Cluster Peripherals, Industrial PLC I/O Module, Body Electronics Lighting Controller.
Automotive Body Control Module
The S912XEQ512J3MALR fits body control modules where multiple LIN sub-nets, switch inputs, and LED drivers must be coordinated from a single MCU. Its 512 KB Flash accommodates body controller firmware including door/window logic, lighting schedules, and diagnostic stacks without resorting to external memory. The XGATE co-processor services LIN interrupts and PWM updates in under 1 µs, freeing the main CPU for application-level state machines. AEC-Q100 qualification to +125 °C supports placement underhood or behind the dashboard where ambient temperatures can spike.
推荐
CAN/LIN Gateway Node
Gateway modules that bridge CAN, LIN, and diagnostic buses benefit from the S912XEQ512J3MALR's combination of multiple CAN controllers, SCI/LIN channels, and 512 KB of Flash for routing tables and protocol stacks. The S12X core can parse and forward frames between buses while the XGATE engine handles time-critical header acceptance-filtering without CPU intervention. Automotive-grade qualification to AEC-Q100 and the -40 °C to +125 °C operating window matches the underhood gateway environment seen in modern passenger vehicles.
推荐
HVAC and Climate Control
HVAC control modules demand precise temperature sensing, PWM fan control, and LIN actuator networks, all of which the S912XEQ512J3MALR can host on a single chip. The 12-bit ADC delivers 3 µs conversion time for NTC thermistor reads at 10 Hz sample rates, while the Enhanced Capture Timer provides PWM generation up to 50 MHz resolution for variable-speed blower control. The 512 KB Flash supports lookup tables for dew-point compensation and cabin-temperature profiling; AEC-Q100 qualification ensures reliable operation behind the dashboard at +125 °C.
推荐
Instrument Cluster Peripherals
Instrument clusters use the S912XEQ512J3MALR to drive stepper motors for gauges, read analog fuel and temperature sensors, and service cluster CAN messages. The S12X core's deterministic interrupt response helps avoid gauge jitter during heavy bus traffic. Memory protection via the supervisor/user mode supports ASIL-B decomposition when the cluster hosts safety-relevant tell-tales. The 112-LQFP footprint gives enough GPIO for multi-stepper drive without external expanders.
推荐
Industrial PLC I/O Module
In industrial PLCs and remote I/O modules the S912XEQ512J3MALR functions as a local controller that scans digital inputs, drives outputs, and reports back over CAN or EtherCAT. The 512 KB Flash holds protocol stacks and ladder-logic interpreters, while the 12-bit ADC monitors analog process variables like pressure or flow. AEC-Q100 qualification at -40 °C to +125 °C exceeds most industrial temperature windows, enabling shared PCB designs between automotive and factory automation variants.
推荐
Body Electronics Lighting Controller
Lighting controllers handle daytime running lights, turn signals, and adaptive headlamp logic, all of which fit inside the S912XEQ512J3MALR's 512 KB Flash and 12-bit ADC. The Enhanced Capture Timer provides PWM dimming resolution up to 16 bits for smooth LED fade ramps. Multiple PWM channels support matrix-beam headlamp arrays, and the hardware-emulated EEPROM stores user-defined lighting profiles without external memory. AEC-Q100 qualification and -40 °C to +125 °C operation suit exterior-mounted lamp modules.
推荐
推荐产品汇总
工程参考数据： S912XEQ512J3MALR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | S912XEQ512J3MAAR | S912XEQ384F1VAL | S912XET512J2VAGR | S912XET256J2VAG |
|---|---|---|---|---|---|
| Package | 112-LQFP (20x20 mm) | 112-LQFP - same | 112-LQFP - same | 112-LQFP - same | 112-LQFP - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core | S12X (HCS12X) | S12X | S12X | S12X | S12X |
| Flash Memory | 512 KB | 512 KB | 384 KB | 512 KB | 256 KB |
| Max CPU Clock | 50 MHz | 50 MHz | 40 MHz | 50 MHz | 50 MHz |
| XGATE Co-processor | Yes | Yes | Yes | Yes | Yes |
| Automotive Qualification | AEC-Q100 (-40 °C to +125 °C) | AEC-Q100 | AEC-Q100 | Industrial grade | Industrial grade |
| Price (qty 100, USD) | 14.08 | 14.08 | 12.85 | 11.40 | 9.95 |
关键差异点
- Highest on-chip Flash in the S12XE 112-LQFP family （对比 S912XEQ384F1VAL)
- AEC-Q100 automotive-grade qualification （对比 S912XET512J2VAGR)
- XGATE co-processor for sub-microsecond interrupt response （对比 Classic HCS12 (MC9S12DT128MPVE))
设计说明
Power the S912XEQ512J3MALR from a regulated 5 V supply with bulk decoupling of 10 µF tantalum plus 100 nF ceramic near the VDD/VDDF pins. The internal 2.5 V regulator output (VDDR) needs its own 1 µF + 100 nF decoupling network to suppress noise coupling into the analog reference. During automotive cranking events (down to 6 V) add a wide-Vin LDO or SEPIC upstream; the on-chip voltage monitor will assert RESET below the brownout threshold. Estimated: total in-rush current peaks at ~80 mA when XGATE and CAN controllers are active simultaneously.
The 112-LQFP package typically exhibits θJA around 35–40 °C/W on a 4-layer JEDEC test board. At -40 °C to +125 °C operation this is acceptable for body-electronics duty cycle (typically <50 % CPU utilization). Place thermal vias under the exposed pad (when present) and avoid routing high-current traces under the LQFP thermal lands; this prevents copper migration that can cause reliability drift. Always validate with board-level thermal profiling per JESD51 standards.
Route the EXTAL/XTAL traces symmetrically and guard them with a ground ring to limit radiated emissions from the fundamental frequency. Keep CAN differential pairs (CAN0TX/RX, CAN1TX/RX) length-matched within 5 mm and routed over a continuous ground plane to meet IEC 62228-3 EMC requirements. Place the BDM connector (BKGD/RESET) at the board edge to enable in-circuit programming without removing the MCU. Add a 4.7 kΩ pull-up on RESET to allow auto-start behavior on power-up.
Do not allocate reserved Flash sectors (typically upper 32 KB) for application code — those sectors are reserved for the hardware-emulated EEPROM. Ensure the XGATE channel assignments are documented in linker files because vector mismatches cause silent peripheral failures. Watch for inadvertent mode transitions in supervisor/user mode after enabling the MPU — uninitialized region descriptors can lock the CPU. Finally, never assert BKGD low during reset unless intentionally entering BDM.
合规信息
AEC-Q100 qualified per NXP product family documentation. RoHS compliant and lead-free per distributor product pages.
