SN74LS640N - 8-Bit Inverting Bus Transceiver | Texas Instruments
料号: SN74LS640N ✓ 量产中SN74LS640N 概述
A bus transceiver is a bidirectional interface IC that combines two drivers and two receivers on each data path. The octal bus transceiver belongs to the broader 74LS logic family and provides a defined interface between two system buses. Its inverting outputs support systems designed around active-low bus conventions, while the 3-state outputs allow devices to relinquish control of a shared bus when disabled.
The SN74LS640 family provides eight parallel data channels with direction control common to all channels. The DIR input selects the transmission direction, and the enable control provides a means to place the outputs in a high-impedance state. This arrangement supports processor-to-peripheral data transfer, bus isolation during inactive periods, and bidirectional communication between assemblies connected by shared wiring.
The key engineering benefit is integration: eight channels, direction control, enable control, and 3-state output behavior are combined in one standard 20-pin PDIP device. The SN74LS640N is appropriate when a legacy system uses LS-family TTL signaling and requires a byte-wide bidirectional bus interface. The N package identifies the through-hole PDIP form rather than a surface-mount package.
Typical uses include parallel peripheral interfaces, asynchronous data exchange between circuit cards, test-equipment control buses, and embedded systems that retain 74LS-compatible logic levels. The common DIR and enable controls simplify firmware because direction and bus participation can be managed as grouped signals instead of eight independent channels.
For reliable operation, treat unused data inputs as defined logic states and do not allow the DIR and enable control inputs to float. Account for propagation delay and setup/hold requirements at the system level when changing direction near a clock edge. The SN74LS640N can remain powered while its outputs are disabled, allowing another bus master to take control without a complete power-cycle.
This page combines the device function, package and interface details with selection guidance for verified drop-in alternatives, practical bus-control considerations, and a parameter-by-parameter comparison for engineers evaluating replacements.
直接替换替代料: SN74LS640N ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
SN54LS640N
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
SN74LS640A
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
SN74LS640N
✅ 直接替换联系询价
查看数据手册 →SN74LS640N
✅ 直接替换联系询价
查看数据手册 →SN74LS640N 最大额定值与电气特性
| Product Type | Octal bus transceiver |
| Logic Family | 74LS |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Direction Control | DIR input |
| Enable Control | G input |
| 输出配置 | 3-state output |
| Output Polarity | Inverting |
| Communication Mode | Asynchronous two-way communication |
| Bus Interface | A bus and B bus |
| 封装 | 20-PDIP |
| 引脚数量 | 20 pins |
| 安装类型 | Through-hole |
SN74LS640N 20-pdip 引脚配置指南
SN74LS640N(20-pdip 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: SN74LS640N.
请参阅 数据手册 以查看完整引脚配置。
典型应用
SN74LS640N 适用于 6 应用s: Bidirectional Parallel Data Buses, Processor-to-Peripheral Interfaces, Multi-Card Backplane Communication, Test and Measurement Equipment, Industrial Control Modules, Embedded Data Acquisition Systems.
Bidirectional Parallel Data Buses
The SN74LS640N provides eight bidirectional data paths between an A bus and a B bus, making it appropriate for an asynchronous byte-wide interface. The DIR input selects the direction for all eight channels, so control logic can switch the direction with one shared signal rather than eight separate commands. Its 3-state outputs let the transceiver release the bus when disabled, which is useful in systems where another master may periodically take control. The 20-PDIP package also supports straightforward prototype construction and field replacement in legacy 74LS-compatible equipment.
推荐
Processor-to-Peripheral Interfaces
The SN74LS640N can connect a processor-side data bus to a peripheral card when the equipment uses 74LS-compatible parallel signaling. Eight channels support full-byte transfers, while DIR provides a straightforward way to reverse control when the peripheral must respond. The enable function allows the interface to be isolated while another device communicates, reducing contention on a shared bus. Engineers should verify propagation delay and setup timing against the processor clock and confirm that the downstream peripheral accepts the inverting output polarity.
推荐
Multi-Card Backplane Communication
The SN74LS640N is suited to legacy backplanes where several circuit cards share eight data conductors. Its high-impedance output state supports bus isolation, while the common DIR and enable controls let a system manager grant one card temporary control of the bus. The inverting transfer characteristic must match the receiving card's data conventions. Because the device operates at 74LS logic levels, designers should also check noise margins, loading, cable length, and timing margin in the completed backplane rather than relying on device capability alone.
推荐
Test and Measurement Equipment
The SN74LS640N can form the interface between an older instrument controller and a peripheral measurement module. Byte-wide bidirectional transfer is convenient for command and response traffic, while the disable function keeps the controller from driving the bus when another instrument has control. The through-hole 20-PDIP package is useful in laboratory and industrial test systems that retain through-hole construction. Before adoption, confirm the instrument's voltage levels, bus timing, and data polarity, and ensure that no control signal can float during reset or power-up transitions.
推荐
Industrial Control Modules
The SN74LS640N can connect legacy industrial controller boards to expansion modules that use shared asynchronous data lines. Its eight parallel channels provide efficient command transfer, and the three-state outputs support a controlled handoff between modules. The DIR control permits rapid reversal when the addressed peripheral becomes the active transmitter. For industrial deployment, verify the part's rated operating temperature and supply range, maintain adequate grounding, and route the bus to minimize coupling from motor-control and switching-power circuits.
推荐
Embedded Data Acquisition Systems
The SN74LS640N is useful when a legacy acquisition controller must exchange eight-bit commands or data with an external instrument or fixture. The bidirectional arrangement reduces the number of interconnects compared with separate unidirectional devices, and the enable input provides active isolation between subsystems. The inverting data convention should be checked at both ends of the link, and system timing should include the transceiver's propagation delay plus the receiver's setup requirement. The 20-PDIP package is particularly convenient for laboratory adapters and hand-built test fixtures.
推荐
推荐产品汇总
工程参考数据: SN74LS640N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | SN54LS640N | SN74LS640A | SN74LS640N | SN74LS640N |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | Motorola |
| Package | 20-PDIP | 20-PDIP - same footprint | 20-PDIP - same footprint | 20-PDIP - same footprint | 20-PDIP - same footprint |
| Function | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver |
| Number of Data Channels | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Output Polarity | Inverting | Inverting | Inverting | Inverting | Inverting |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state |
| Direction Control | DIR input | DIR input | DIR input | DIR input | DIR input |
| Enable Control | G input | G input | G input | G input | G input |
| Communication Mode | Asynchronous two-way communication | Asynchronous two-way communication | Asynchronous two-way communication | Asynchronous two-way communication | Asynchronous two-way communication |
关键差异点
- Eight inverting channels share one direction control (对比 SN74LS645N)
- Exact onsemi part-number match in the verified cross-reference records (对比 SN74LS640N from onsemi)
- Available temperature-grade differentiation within the same TI family (对比 SN54LS640N)
设计说明
Do not allow DIR or the enable input to float during reset, power-up, or controller loss. A floating control input can place the eight outputs in an unpredictable state and create contention on a shared bus. Add suitable pull resistors or ensure that the controlling logic and its reset defaults explicitly hold the interface disabled. Verify the selected logic levels against the SN74LS640 datasheet before connecting the controls to a newer 3.3 V or 5 V controller.
Sequence direction changes so the currently active driver is disabled before another device or direction is enabled. Account for propagation delay, receiver setup time, and bus-settling time when calculating the interval between DIR changes and valid-data sampling. The shared DIR control changes all eight channels simultaneously, so a single timing decision governs the complete byte. For longer cables or slow buses, add termination and verify signal integrity at the receiver rather than relying only on component timing.
Follow the manufacturer's 20-PDIP pin-description table when assigning PCB nets and preserve the standard through-hole footprint. Keep the A-bus and B-bus routing away from switching nodes, relay contacts, and high-current return paths to prevent bus errors. Place any pull resistors near the devices that control DIR and enable, and use a common ground reference for every interface connected to the bus. Confirm unused-pin treatment and exposed-versus-thermal-pad requirements in the exact package drawing.
The transceiver's supply rail must remain within the device's specified operating range, and the connected logic must share compatible input thresholds and output levels. The enable function can isolate the buses while power remains applied, but it does not remove the need for a valid supply. Avoid relying on the transceiver to absorb ground offsets between separately powered circuit cards; verify common-mode limits and provide a suitable reference strategy before interconnecting equipment.
合规信息
The available product records do not provide explicit compliance declarations for this exact MPN. Automotive qualification is not applicable to this logic transceiver.