Texas Instruments

SN74LS640N - 8-Bit Inverting Bus Transceiver | Texas Instruments

MPN: SN74LS640N ✓ Hoạt động
20-PDIP Package
MOQ: 1 |

SN74LS640N Tóm tắt

Texas Instruments SN74LS640N is an 8-bit inverting bus transceiver with 3-state outputs, designed for asynchronous two-way communication between data buses in a 20-pin PDIP package. It transmits data from the A bus to the B bus or from the B bus to the A bus according to the DIR input, while the enable input can disable the device so the buses are effectively isolated.

A bus transceiver is a bidirectional interface IC that combines two drivers and two receivers on each data path. The octal bus transceiver belongs to the broader 74LS logic family and provides a defined interface between two system buses. Its inverting outputs support systems designed around active-low bus conventions, while the 3-state outputs allow devices to relinquish control of a shared bus when disabled.

The SN74LS640 family provides eight parallel data channels with direction control common to all channels. The DIR input selects the transmission direction, and the enable control provides a means to place the outputs in a high-impedance state. This arrangement supports processor-to-peripheral data transfer, bus isolation during inactive periods, and bidirectional communication between assemblies connected by shared wiring.

The key engineering benefit is integration: eight channels, direction control, enable control, and 3-state output behavior are combined in one standard 20-pin PDIP device. The SN74LS640N is appropriate when a legacy system uses LS-family TTL signaling and requires a byte-wide bidirectional bus interface. The N package identifies the through-hole PDIP form rather than a surface-mount package.

Typical uses include parallel peripheral interfaces, asynchronous data exchange between circuit cards, test-equipment control buses, and embedded systems that retain 74LS-compatible logic levels. The common DIR and enable controls simplify firmware because direction and bus participation can be managed as grouped signals instead of eight independent channels.

For reliable operation, treat unused data inputs as defined logic states and do not allow the DIR and enable control inputs to float. Account for propagation delay and setup/hold requirements at the system level when changing direction near a clock edge. The SN74LS640N can remain powered while its outputs are disabled, allowing another bus master to take control without a complete power-cycle.

This page combines the device function, package and interface details with selection guidance for verified drop-in alternatives, practical bus-control considerations, and a parameter-by-parameter comparison for engineers evaluating replacements.

Bộ thay thế dễ dàng lắp đặt cho SN74LS640N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

SN54LS640N

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 20-PDIP
Same 8-bit inverting 3-state transceiver function and 20-pin pinout; military-temperature grade differs from the commercial SN74LS640N, so temperature coverage is the principal quantified distinction.

📋 Tham chiếu thay thế (không có trong danh mục)

SN74LS640A

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 20-PDIP
Same 8-bit inverting bus-transceiver architecture in a 20-pin package; the A revision can have revised timing or electrical characteristics, so propagation delay and operating limits require comparison.

📋 Tham chiếu thay thế (không có trong danh mục)

SN74LS640N

✅ Drop-In
Texas Instruments
📦 20-PDIP
Octal bus transceiver · 74LS · 1 element · 8 bits · DIR input · G input · 3-state output · Inverting

Liên hệ để biết giá

Xem tài liệu →

SN74LS640N

✅ Drop-In
Texas Instruments
📦 20-PDIP
Octal bus transceiver · 74LS · 1 element · 8 bits · DIR input · G input · 3-state output · Inverting

Liên hệ để biết giá

Xem tài liệu →

SN74LS640N Tỷ lệ tối đa & tính chất điện

Product Type Octal bus transceiver
Logic Family 74LS
Number of Elements 1 element
Bits per Element 8 bits
Direction Control DIR input
Enable Control G input
Cấu hình đầu ra 3-state output
Output Polarity Inverting
Communication Mode Asynchronous two-way communication
Bus Interface A bus and B bus
Hộp 20-PDIP
Số chân 20 pins
Kiểu lắp đặt Through-hole

Hướng dẫn cấu hình chân SN74LS640N 20-pdip

Cấu hình chân cho SN74LS640N (20-pdip gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.

Bảng cấu hình chân 20-pdip cho SN74LS640N

Không có dữ liệu chân cụ thể sẵn có cho SN74LS640N.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

SN74LS640N phù hợp cho 6 Áp dụngs: Bidirectional Parallel Data Buses, Processor-to-Peripheral Interfaces, Multi-Card Backplane Communication, Test and Measurement Equipment, Industrial Control Modules, Embedded Data Acquisition Systems.

🌐

Bidirectional Parallel Data Buses

The SN74LS640N provides eight bidirectional data paths between an A bus and a B bus, making it appropriate for an asynchronous byte-wide interface. The DIR input selects the direction for all eight channels, so control logic can switch the direction with one shared signal rather than eight separate commands. Its 3-state outputs let the transceiver release the bus when disabled, which is useful in systems where another master may periodically take control. The 20-PDIP package also supports straightforward prototype construction and field replacement in legacy 74LS-compatible equipment.

🖥️

Processor-to-Peripheral Interfaces

The SN74LS640N can connect a processor-side data bus to a peripheral card when the equipment uses 74LS-compatible parallel signaling. Eight channels support full-byte transfers, while DIR provides a straightforward way to reverse control when the peripheral must respond. The enable function allows the interface to be isolated while another device communicates, reducing contention on a shared bus. Engineers should verify propagation delay and setup timing against the processor clock and confirm that the downstream peripheral accepts the inverting output polarity.

🏭

Multi-Card Backplane Communication

The SN74LS640N is suited to legacy backplanes where several circuit cards share eight data conductors. Its high-impedance output state supports bus isolation, while the common DIR and enable controls let a system manager grant one card temporary control of the bus. The inverting transfer characteristic must match the receiving card's data conventions. Because the device operates at 74LS logic levels, designers should also check noise margins, loading, cable length, and timing margin in the completed backplane rather than relying on device capability alone.

🔧

Test and Measurement Equipment

The SN74LS640N can form the interface between an older instrument controller and a peripheral measurement module. Byte-wide bidirectional transfer is convenient for command and response traffic, while the disable function keeps the controller from driving the bus when another instrument has control. The through-hole 20-PDIP package is useful in laboratory and industrial test systems that retain through-hole construction. Before adoption, confirm the instrument's voltage levels, bus timing, and data polarity, and ensure that no control signal can float during reset or power-up transitions.

⚡

Industrial Control Modules

The SN74LS640N can connect legacy industrial controller boards to expansion modules that use shared asynchronous data lines. Its eight parallel channels provide efficient command transfer, and the three-state outputs support a controlled handoff between modules. The DIR control permits rapid reversal when the addressed peripheral becomes the active transmitter. For industrial deployment, verify the part's rated operating temperature and supply range, maintain adequate grounding, and route the bus to minimize coupling from motor-control and switching-power circuits.

📡

Embedded Data Acquisition Systems

The SN74LS640N is useful when a legacy acquisition controller must exchange eight-bit commands or data with an external instrument or fixture. The bidirectional arrangement reduces the number of interconnects compared with separate unidirectional devices, and the enable input provides active isolation between subsystems. The inverting data convention should be checked at both ends of the link, and system timing should include the transceiver's propagation delay plus the receiver's setup requirement. The 20-PDIP package is particularly convenient for laboratory adapters and hand-built test fixtures.

What is the SN74LS640N?
The SN74LS640N is an 8-bit inverting bus transceiver with 3-state outputs in a 20-pin PDIP package. According to the Texas Instruments SN74LS640 datasheet, it supports asynchronous two-way communication between A and B data buses, with the DIR input selecting transmission direction and the G enable input isolating the buses when the device is disabled.
How does the DIR input work on the SN74LS640N?
The DIR input controls all eight data channels and selects the direction of bus transmission. According to the Texas Instruments SN74LS640 datasheet, data moves from the A bus to the B bus or from the B bus to the A bus depending on the DIR level. Designers should allow the device to settle before sampling transferred data, particularly when reversing direction near a clock boundary.
What does the 3-state output provide on the SN74LS640N?
The SN74LS640N provides a high-impedance output state so several devices can share a bus without driving it simultaneously. According to the Texas Instruments SN74LS640 datasheet, the enable input can disable the device so the buses are effectively isolated. This feature supports bus arbitration, expansion, and orderly handoff between circuit cards.
What is the difference between the A and B buses on the SN74LS640N?
The A and B buses are the two eight-bit sides of the SN74LS640N transceiver, with each channel providing a path between them. According to the Texas Instruments SN74LS640 datasheet, the DIR input determines whether data is transmitted from A to B or from B to A. The active-low enable function can isolate the interface when neither side should drive the shared connection.
What package and pin count does the SN74LS640N use?
The SN74LS640N uses a 20-pin PDIP through-hole package. The Texas Instruments product listing identifies the device as a 20-PDIP octal bus transceiver, while the N suffix identifies this package configuration. Use the manufacturer pin-description table and package drawing when assigning PCB tracks because individual pin functions and no-connect positions must follow that documentation.
Is the SN74LS640N suitable for an 8-bit parallel interface?
Yes, the SN74LS640N is designed for byte-wide parallel communication because it contains eight data channels in one device. The DIR and enable controls operate across all eight channels, which simplifies control of an asynchronous 8-bit bus. The interface is appropriate where existing electronics use 74LS-compatible signal levels and require bidirectional operation.
Where can I download the SN74LS640N datasheet PDF?
The official SN74LS640N datasheet is available through Texas Instruments at the product literature link for SN74LS640. The manufacturer datasheet describes the octal-bus architecture, DIR and enable controls, electrical characteristics, and package information. Use the manufacturer document for final pin assignments, timing limits, and supply limits before completing a circuit design.
Where can I find the SN74LS640N pinout?
The SN74LS640N pinout is shown in the Texas Instruments SN74LS640 manufacturer datasheet. Use the pin-description table together with the 20-PDIP outline to assign the DIR input, enable control, A-bus and B-bus data pins, ground, and supply connections. Do not infer unused-pin assignments from a generic 74-series socket diagram because devices in the family can use control pins differently.
What can replace the SN74LS640N?
The best replacement is a pin-compatible octal inverting bus transceiver in the same 20-PDIP footprint with equivalent DIR and enable behavior. Verified manufacturer and cross-reference records identify the onsemi and legacy Motorola SN74LS640N entries, while the SN54LS640N family provides a military-temperature option. Confirm supply limits, timing, and temperature requirements before approving any substitute.
Is the SN74LS640N the same as the SN74LS640NS?
The SN74LS640N and SN74LS640NS represent different orderable package or shipping configurations rather than meaningfully different electrical functions. For PCB replacement, use the manufacturer ordering information to confirm whether the installed part is the through-hole N configuration or the surface-mount NS configuration. The SN74LS640NS should not be treated as a drop-in substitute for a 20-PDIP footprint.
What is the best onsemi equivalent for the SN74LS640N?
The onsemi SN74LS640N is the closest identified cross-brand match because it carries the same manufacturer part number and is listed as an octal bus transceiver. Its 20-PDIP compatibility must be confirmed against the onsemi ordering documentation and the Texas Instruments pin description. Validate voltage, temperature, propagation-delay, and enable-polarity requirements before production use.
SN74LS640N versus SN74LS645N: which one should I choose?
Choose the SN74LS640N when the receiving circuitry expects inverted data, and choose the SN74LS645N when non-inverting bus data is required. The SN74LS640N is identified as an inverting 3-state octal transceiver, while the SN74LS645N has a different output polarity. They serve related bus-interface roles but are not interchangeable when downstream logic depends on inversion.
When should I choose the SN74LS640N over a non-inverting transceiver?
Choose the SN74LS640N when the receiving bus expects inverted logic and the system already uses 74LS-family signaling conventions. Its eight channels, shared DIR control, enable isolation, and 3-state outputs suit asynchronous byte-wide buses. Select a non-inverting part only when the receiving logic requires the opposite polarity and timing, voltage, and package requirements are otherwise equivalent.
Is the SN74LS640N suitable for industrial control and test systems?
The SN74LS640N can be suitable in legacy control and test systems that use 74LS-compatible asynchronous buses. Its 20-PDIP through-hole package simplifies repair and prototype construction, while the three-state outputs support shared-bus arrangements. The specific operating temperature, supply voltage, noise margin, and lifecycle requirements must be checked against the environmental needs of the finished equipment.
How should DIR and enable be controlled when the SN74LS640N changes bus direction?
Drive DIR and the enable input from defined logic states and avoid allowing either control input to float. Before reversing direction, disable the outputs and allow the transceiver to settle, then enable the new direction after the receiving bus is ready. The Texas Instruments SN74LS640 datasheet defines the control architecture, while the system timing budget must establish safe setup intervals.
Where can I request a quote for SN74LS640N?
Use the Request a Quote form on this page to request current SN74LS640N commercial terms, stock confirmation, and a quantity lead-time estimate. Quote requests allow the exact MPN and package to be reviewed against your order quantity. Current availability and lead time should be confirmed at the time of quotation rather than inferred from a product-page listing.
What is the current price of the SN74LS640N?
The current SN74LS640N commercial price is not stated as fixed text because it can change with order quantity, supply, and requested delivery terms. Use the Request a Quote form on this page and enter the exact MPN, quantity, and packaging requirement. The structured pricing area on the page should be used for the currently displayed quotation basis.
Is the SN74LS640N in stock and what is its lead time?
Stock and lead time should be confirmed through the Request a Quote form on this page for the exact SN74LS640N and required quantity. Catalog status alone does not guarantee immediate availability, particularly for older LS-series logic in a 20-PDIP package. Provide your schedule and annual usage so the quotation can reflect the appropriate allocation and production lead time.

Dữ liệu tham khảo kỹ thuật cho SN74LS640N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the SN74LS640N when maintaining or designing a legacy system that uses an 8-bit asynchronous bus, requires inverting data, and expects a 20-pin PDIP 74LS-family transceiver. The three-state outputs and common DIR and enable controls make it useful when devices share a bus, but the receiving logic must match its inverting convention. Consider the SN54LS640N when the same electrical function is needed over a wider temperature range. The SN74LS640A may be appropriate when its revision-specific timing characteristics provide a better fit, although the original SN74LS640N remains the direct baseline for an existing design. The onsemi and legacy Motorola SN74LS640N records are exact-part-number alternatives, so compare their current electrical limits, qualification status, and supply before approving a change. Do not select the SN74LS645N as a direct replacement when inversion affects system behavior.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này SN54LS640N SN74LS640A SN74LS640N SN74LS640N
Brand Texas Instruments Texas Instruments Texas Instruments onsemi Motorola
Package 20-PDIP 20-PDIP - same footprint 20-PDIP - same footprint 20-PDIP - same footprint 20-PDIP - same footprint
Function Octal inverting bus transceiver Octal inverting bus transceiver Octal inverting bus transceiver Octal inverting bus transceiver Octal inverting bus transceiver
Number of Data Channels 8 bits 8 bits 8 bits 8 bits 8 bits
Output Polarity Inverting Inverting Inverting Inverting Inverting
Output State 3-state 3-state 3-state 3-state 3-state
Direction Control DIR input DIR input DIR input DIR input DIR input
Enable Control G input G input G input G input G input
Communication Mode Asynchronous two-way communication Asynchronous two-way communication Asynchronous two-way communication Asynchronous two-way communication Asynchronous two-way communication

Bảo phân biệt quan trọng

  • Eight inverting channels share one direction control (vsSN74LS645N)
  • Exact onsemi part-number match in the verified cross-reference records (vsSN74LS640N from onsemi)
  • Available temperature-grade differentiation within the same TI family (vsSN54LS640N)

Ghi chú thiết kế

Do not allow DIR or the enable input to float during reset, power-up, or controller loss. A floating control input can place the eight outputs in an unpredictable state and create contention on a shared bus. Add suitable pull resistors or ensure that the controlling logic and its reset defaults explicitly hold the interface disabled. Verify the selected logic levels against the SN74LS640 datasheet before connecting the controls to a newer 3.3 V or 5 V controller.

Sequence direction changes so the currently active driver is disabled before another device or direction is enabled. Account for propagation delay, receiver setup time, and bus-settling time when calculating the interval between DIR changes and valid-data sampling. The shared DIR control changes all eight channels simultaneously, so a single timing decision governs the complete byte. For longer cables or slow buses, add termination and verify signal integrity at the receiver rather than relying only on component timing.

Follow the manufacturer's 20-PDIP pin-description table when assigning PCB nets and preserve the standard through-hole footprint. Keep the A-bus and B-bus routing away from switching nodes, relay contacts, and high-current return paths to prevent bus errors. Place any pull resistors near the devices that control DIR and enable, and use a common ground reference for every interface connected to the bus. Confirm unused-pin treatment and exposed-versus-thermal-pad requirements in the exact package drawing.

The transceiver's supply rail must remain within the device's specified operating range, and the connected logic must share compatible input thresholds and output levels. The enable function can isolate the buses while power remains applied, but it does not remove the need for a valid supply. Avoid relying on the transceiver to absorb ground offsets between separately powered circuit cards; verify common-mode limits and provide a suitable reference strategy before interconnecting equipment.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The available product records do not provide explicit compliance declarations for this exact MPN. Automotive qualification is not applicable to this logic transceiver.

Tìm kiếm liên quan

SN74LS640N datasheet SN74LS640N pinout SN74LS640N datasheet pdf SN74LS640N equivalent SN74LS640N replacement SN74LS640N cross reference SN74LS640N price SN74LS640N stock Texas Instruments SN74LS640N SN74LS640N 20-PDIP SN74LS640N vs SN74LS645N SN74LS640N DIR enable SN74LS640N bus transceiver SN74LS640N 8-bit 3-state

Các bộ phận và thuật ngữ liên quan

Texas Instruments SN74LS640N SN54LS640N SN74LS640A SN74LS645N onsemi Motorola 74LS logic family octal bus transceiver bidirectional bus interface asynchronous communication three-state output high-impedance state DIR input enable input inverting logic A bus B bus 20-PDIP DIP package family through-hole mounting logic IC bus contention propagation delay data bus isolation
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ