SN74LS640N - 8-Bit Inverting Bus Transceiver | Texas Instruments
부품 번호: SN74LS640N ✓ 활성SN74LS640N 개요
A bus transceiver is a bidirectional interface IC that combines two drivers and two receivers on each data path. The octal bus transceiver belongs to the broader 74LS logic family and provides a defined interface between two system buses. Its inverting outputs support systems designed around active-low bus conventions, while the 3-state outputs allow devices to relinquish control of a shared bus when disabled.
The SN74LS640 family provides eight parallel data channels with direction control common to all channels. The DIR input selects the transmission direction, and the enable control provides a means to place the outputs in a high-impedance state. This arrangement supports processor-to-peripheral data transfer, bus isolation during inactive periods, and bidirectional communication between assemblies connected by shared wiring.
The key engineering benefit is integration: eight channels, direction control, enable control, and 3-state output behavior are combined in one standard 20-pin PDIP device. The SN74LS640N is appropriate when a legacy system uses LS-family TTL signaling and requires a byte-wide bidirectional bus interface. The N package identifies the through-hole PDIP form rather than a surface-mount package.
Typical uses include parallel peripheral interfaces, asynchronous data exchange between circuit cards, test-equipment control buses, and embedded systems that retain 74LS-compatible logic levels. The common DIR and enable controls simplify firmware because direction and bus participation can be managed as grouped signals instead of eight independent channels.
For reliable operation, treat unused data inputs as defined logic states and do not allow the DIR and enable control inputs to float. Account for propagation delay and setup/hold requirements at the system level when changing direction near a clock edge. The SN74LS640N can remain powered while its outputs are disabled, allowing another bus master to take control without a complete power-cycle.
This page combines the device function, package and interface details with selection guidance for verified drop-in alternatives, practical bus-control considerations, and a parameter-by-parameter comparison for engineers evaluating replacements.
드롭인 대체품: SN74LS640N — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
SN54LS640N
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
SN74LS640A
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
SN74LS640N
✅ 드롭인가격 문의
데이터시트 보기 →SN74LS640N
✅ 드롭인가격 문의
데이터시트 보기 →SN74LS640N 최대 정격 & 전기적 특성
| Product Type | Octal bus transceiver |
| Logic Family | 74LS |
| Number of Elements | 1 element |
| Bits per Element | 8 bits |
| Direction Control | DIR input |
| Enable Control | G input |
| 출력 구성 | 3-state output |
| Output Polarity | Inverting |
| Communication Mode | Asynchronous two-way communication |
| Bus Interface | A bus and B bus |
| 패키지 | 20-PDIP |
| 핀 수 | 20 pins |
| 실장 유형 | Through-hole |
SN74LS640N 20-pdip 핀 구성 가이드
SN74LS640N(20-pdip 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: SN74LS640N.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
SN74LS640N 적합 용도: 6 애플리케이션s: Bidirectional Parallel Data Buses, Processor-to-Peripheral Interfaces, Multi-Card Backplane Communication, Test and Measurement Equipment, Industrial Control Modules, Embedded Data Acquisition Systems.
Bidirectional Parallel Data Buses
The SN74LS640N provides eight bidirectional data paths between an A bus and a B bus, making it appropriate for an asynchronous byte-wide interface. The DIR input selects the direction for all eight channels, so control logic can switch the direction with one shared signal rather than eight separate commands. Its 3-state outputs let the transceiver release the bus when disabled, which is useful in systems where another master may periodically take control. The 20-PDIP package also supports straightforward prototype construction and field replacement in legacy 74LS-compatible equipment.
추천
Processor-to-Peripheral Interfaces
The SN74LS640N can connect a processor-side data bus to a peripheral card when the equipment uses 74LS-compatible parallel signaling. Eight channels support full-byte transfers, while DIR provides a straightforward way to reverse control when the peripheral must respond. The enable function allows the interface to be isolated while another device communicates, reducing contention on a shared bus. Engineers should verify propagation delay and setup timing against the processor clock and confirm that the downstream peripheral accepts the inverting output polarity.
추천
Multi-Card Backplane Communication
The SN74LS640N is suited to legacy backplanes where several circuit cards share eight data conductors. Its high-impedance output state supports bus isolation, while the common DIR and enable controls let a system manager grant one card temporary control of the bus. The inverting transfer characteristic must match the receiving card's data conventions. Because the device operates at 74LS logic levels, designers should also check noise margins, loading, cable length, and timing margin in the completed backplane rather than relying on device capability alone.
추천
Test and Measurement Equipment
The SN74LS640N can form the interface between an older instrument controller and a peripheral measurement module. Byte-wide bidirectional transfer is convenient for command and response traffic, while the disable function keeps the controller from driving the bus when another instrument has control. The through-hole 20-PDIP package is useful in laboratory and industrial test systems that retain through-hole construction. Before adoption, confirm the instrument's voltage levels, bus timing, and data polarity, and ensure that no control signal can float during reset or power-up transitions.
추천
Industrial Control Modules
The SN74LS640N can connect legacy industrial controller boards to expansion modules that use shared asynchronous data lines. Its eight parallel channels provide efficient command transfer, and the three-state outputs support a controlled handoff between modules. The DIR control permits rapid reversal when the addressed peripheral becomes the active transmitter. For industrial deployment, verify the part's rated operating temperature and supply range, maintain adequate grounding, and route the bus to minimize coupling from motor-control and switching-power circuits.
추천
Embedded Data Acquisition Systems
The SN74LS640N is useful when a legacy acquisition controller must exchange eight-bit commands or data with an external instrument or fixture. The bidirectional arrangement reduces the number of interconnects compared with separate unidirectional devices, and the enable input provides active isolation between subsystems. The inverting data convention should be checked at both ends of the link, and system timing should include the transceiver's propagation delay plus the receiver's setup requirement. The 20-PDIP package is particularly convenient for laboratory adapters and hand-built test fixtures.
추천
추천 제품 요약
엔지니어링 참조 데이터: SN74LS640N — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | SN54LS640N | SN74LS640A | SN74LS640N | SN74LS640N |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | Motorola |
| Package | 20-PDIP | 20-PDIP - same footprint | 20-PDIP - same footprint | 20-PDIP - same footprint | 20-PDIP - same footprint |
| Function | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver | Octal inverting bus transceiver |
| Number of Data Channels | 8 bits | 8 bits | 8 bits | 8 bits | 8 bits |
| Output Polarity | Inverting | Inverting | Inverting | Inverting | Inverting |
| Output State | 3-state | 3-state | 3-state | 3-state | 3-state |
| Direction Control | DIR input | DIR input | DIR input | DIR input | DIR input |
| Enable Control | G input | G input | G input | G input | G input |
| Communication Mode | Asynchronous two-way communication | Asynchronous two-way communication | Asynchronous two-way communication | Asynchronous two-way communication | Asynchronous two-way communication |
주요 차별점
- Eight inverting channels share one direction control (vs SN74LS645N)
- Exact onsemi part-number match in the verified cross-reference records (vs SN74LS640N from onsemi)
- Available temperature-grade differentiation within the same TI family (vs SN54LS640N)
설계 노트
Do not allow DIR or the enable input to float during reset, power-up, or controller loss. A floating control input can place the eight outputs in an unpredictable state and create contention on a shared bus. Add suitable pull resistors or ensure that the controlling logic and its reset defaults explicitly hold the interface disabled. Verify the selected logic levels against the SN74LS640 datasheet before connecting the controls to a newer 3.3 V or 5 V controller.
Sequence direction changes so the currently active driver is disabled before another device or direction is enabled. Account for propagation delay, receiver setup time, and bus-settling time when calculating the interval between DIR changes and valid-data sampling. The shared DIR control changes all eight channels simultaneously, so a single timing decision governs the complete byte. For longer cables or slow buses, add termination and verify signal integrity at the receiver rather than relying only on component timing.
Follow the manufacturer's 20-PDIP pin-description table when assigning PCB nets and preserve the standard through-hole footprint. Keep the A-bus and B-bus routing away from switching nodes, relay contacts, and high-current return paths to prevent bus errors. Place any pull resistors near the devices that control DIR and enable, and use a common ground reference for every interface connected to the bus. Confirm unused-pin treatment and exposed-versus-thermal-pad requirements in the exact package drawing.
The transceiver's supply rail must remain within the device's specified operating range, and the connected logic must share compatible input thresholds and output levels. The enable function can isolate the buses while power remains applied, but it does not remove the need for a valid supply. Avoid relying on the transceiver to absorb ground offsets between separately powered circuit cards; verify common-mode limits and provide a suitable reference strategy before interconnecting equipment.
규정 준수 정보
The available product records do not provide explicit compliance declarations for this exact MPN. Automotive qualification is not applicable to this logic transceiver.