STM32L4P5VET6 - 120MHz Cortex-M4 MCU, 512KB Flash | STMicroelectronics
料号: STM32L4P5VET6 ✓ 量产中STM32L4P5VET6 概述
An ultra-low-power microcontroller is an integrated semiconductor that combines a processor core, memory, peripherals, and communication interfaces on one device. The STM32L4+ family belongs to the Arm Cortex-M4 microcontroller hierarchy and targets applications where responsive real-time processing must coexist with low standby current, efficient active-mode operation, and compact embedded control.
The STM32L4P5VET6 provides a 120 MHz Arm Cortex-M4 core, 32-bit architecture, and 512 KB of Flash for firmware and application code. Its 100-pin LQFP package supports a broad peripheral complement for sensor acquisition, communications, human-machine interfaces, and connected industrial equipment. The listed feature set includes USB OTG and DFSDM, while the 12-bit ADC and DAC resources support precision measurement and signal generation.
The high-performance Cortex-M4 architecture uses a reduced instruction set and includes floating-point capability for efficient digital signal processing and control-loop calculations. USB OTG supports direct USB connectivity for configuration, data transfer, and peripheral interfacing, while DFSDM provides a dedicated path for high-rate digital signal acquisition from external converters. These integrated functions reduce reliance on external interface devices in compact designs.
Typical applications include industrial sensor hubs, building automation controllers, USB-connected data-acquisition systems, portable medical or test equipment, low-power edge nodes, and compact motor-control or measurement products. The combination of 512 KB Flash, USB connectivity, and 120 MHz processing is particularly useful when local control logic, communications, and signal processing must share one microcontroller.
PCB design should preserve clean separation between analog and digital signals, route high-speed or USB interfaces with controlled impedance, and place decoupling capacitors close to the supply pins. Firmware must also be validated against the device pin definitions and peripheral requirements in the manufacturer datasheet before PCB routing or production release.
This page combines device specifications, practical application guidance, and engineering-focused comparisons to support MCU selection, schematic review, PCB planning, and sourcing decisions for the STM32L4P5VET6.
直接替换替代料: STM32L4P5VET6 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: STM32L4P5VET6 (相同外形与封装尺寸) ——差异在于 ADC Resolution, Package, Processor Core, Product Type.
STM32L451VET6
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
STM32L452VET6
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
STM32L462VET6
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
STM32L471VET6
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →STM32L475VET6
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
STM32L4P5VET6 最大额定值与电气特性
| Manufacturer | STMicroelectronics |
| Product Type | 32-bit ARM Cortex-M4 ultra-low-power microcontroller |
| Processor Core | Arm Cortex-M4 with FPU |
| Maximum CPU Frequency | 120 MHz |
| Architecture | 32-bit RISC |
| Embedded Flash Memory | 512 KB (512K x 8) |
| 工作电源电压 | 3.3 V |
| USB Interface | USB OTG |
| Digital Filter for Sigma-Delta Modulators | DFSDM |
| ADC Resolution | 12-bit |
| DAC Resolution | 12-bit |
| 封装 | 100-pin LQFP (14 mm x 14 mm) |
| 安装类型 | Surface mount |
STM32L4P5VET6 100-pin lqfp (14 mm x 14 mm) 引脚配置指南
STM32L4P5VET6(100-pin lqfp (14 mm x 14 mm) 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: STM32L4P5VET6.
请参阅 数据手册 以查看完整引脚配置。
典型应用
STM32L4P5VET6 适用于 6 应用s: USB Sensor Hub, Industrial Data Acquisition, Building Automation Controller, Portable Medical Monitor, Low-Power Edge Sensor Node, Test and Measurement Instrument.
USB Sensor Hub
The STM32L4P5VET6 fits a USB sensor hub because its 120 MHz Arm Cortex-M4 core can process multiple sensor streams while USB OTG provides a direct device interface. The 512 KB Flash capacity accommodates firmware, configuration data, and device-management code without requiring a separate program-memory device. A practical implementation uses the USB interface for command and data traffic while DFSDM can accept suitable digital sensor streams. Designers should account for connector protection, controlled-impedance USB routing, solid grounding, and firmware scheduling so high-rate transfers do not delay control functions.
Industrial Data Acquisition
The STM32L4P5VET6 is well suited to industrial data-acquisition equipment requiring 12-bit conversion resources, a 120 MHz processing core, and 512 KB of local Flash. Its 100-pin LQFP interface can support analog inputs, digital sensing, communications, and local storage in one controller. DFSDM can provide a dedicated digital acquisition path when the sensor or converter uses a compatible sigma-delta interface. The principal design consideration is maintaining clean analog and digital partitioning while minimizing conversion, reference, and switching-noise errors that can dominate measurement accuracy.
Building Automation Controller
The STM32L4P5VET6 can serve as a building-automation controller where energy management, environmental sensing, and communications must share a compact embedded platform. Its 120 MHz Cortex-M4 core provides headroom for protocol handling and real-time control, while 512 KB of Flash supports application firmware and local configuration. The 100-pin LQFP package offers extensive routing options for serial interfaces, digital inputs, and analog sensing. Firmware should use a deterministic scheduling approach, and PCB layout should isolate sensor inputs and communication interfaces from switching regulators and high-current actuator outputs.
Portable Medical Monitor
The STM32L4P5VET6 is applicable to portable monitoring equipment that combines sensor conditioning, digital processing, USB connectivity, and a compact display interface. Its 120 MHz Cortex-M4 core supports filtering and real-time analysis, and its 512 KB Flash provides room for embedded firmware and parameter sets. USB OTG enables configuration, logging, or synchronization with a host device. For a medical product, the developer must also define signal isolation, patient protection, electrical-safety boundaries, calibration, and regulatory validation independently of the MCU selection.
Low-Power Edge Sensor Node
The STM32L4P5VET6 fits an edge sensor node that must process local measurements while minimizing energy use. Its ultra-low-power STM32L4+ architecture supports duty-cycled sensing and communications, and the 120 MHz core allows time-critical filtering to run without moving every calculation to a higher-power host. The 512 KB Flash supports protocol handlers, event logic, and update-capable firmware. Real deployment should validate sleep-mode current, wake-up latency, analog-front-end noise, and regulator efficiency across the complete environmental test range.
Test and Measurement Instrument
The STM32L4P5VET6 is appropriate for compact test and measurement products that combine fast acquisition, local processing, and USB connectivity. Its 120 MHz Cortex-M4 core can execute digital filtering, calibration routines, and instrument-control logic, while DFSDM supports compatible high-resolution acquisition stages and 12-bit converters support direct analog measurement. The 100-pin LQFP package leaves access to programming and communication interfaces while keeping the device easy to assemble. Calibration tables, reference design, analog-layout discipline, and traceable firmware updates remain essential to measurement quality.
工程参考数据: STM32L4P5VET6 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | STM32L451VET6 | STM32L452VET6 | STM32L462VET6 | STM32L471VET6 | STM32L475VET6 |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 100-pin LQFP (14 mm x 14 mm) | 100-pin LQFP (14 mm x 14 mm) | 100-pin LQFP (14 mm x 14 mm) | 100-pin LQFP (14 mm x 14 mm) | 100-pin LQFP (14 mm x 14 mm) | 100-pin LQFP (14 mm x 14 mm) |
| Processor Core | Arm Cortex-M4 with FPU | Arm Cortex-M4 with FPU | Arm Cortex-M4 with FPU | Arm Cortex-M4 with FPU | Arm Cortex-M4 with FPU | Arm Cortex-M4 with FPU |
| Maximum CPU Frequency | 120 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Embedded Flash Memory | 512 KB (512K x 8) | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB |
| Architecture | 32-bit RISC | 32-bit RISC | 32-bit RISC | 32-bit RISC | 32-bit RISC | 32-bit RISC |
| USB Interface | USB OTG | USB device capability | USB OTG | USB OTG | USB OTG | USB OTG |
| ADC Resolution | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit |
| DAC Resolution | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit | 12-bit |
关键差异点
- Higher processing ceiling within the compared STM32L4 100-pin options (对比 STM32L452VET6)
- USB and DFSDM integration for connected acquisition systems (对比 STM32L451VET6)
- 512 KB Flash with a 120 MHz Cortex-M4 core (对比 STM32L471VET6)
- Performance headroom for local filtering and control (对比 STM32L475VET6)
设计说明
Route USB and other high-speed interfaces as controlled-impedance nets with a continuous reference plane and minimized branch lengths. Keep the USB connector, protection devices, and MCU-side routing in one defined signal region. Avoid placing switching-regulator power paths beneath USB data lines, because inductors and discontinuous current loops can increase radiated emissions and compromise signal integrity.
Do not treat an STM32L4 family pin compatibility claim as a complete replacement qualification. Before substituting the STM32L4P5VET6 with STM32L451VET6, STM32L452VET6, STM32L462VET6, STM32L471VET6, or STM32L475VET6, verify boot configuration, oscillator pins, debug connections, analog functions, communication peripherals, interrupt assignments, and the maximum clock required by the application. A footprint match alone does not guarantee identical firmware behavior.
Place every required decoupling capacitor close to the corresponding power and ground pins, following the capacitor values and network shown in the manufacturer datasheet. Provide adequate bulk charge near the MCU and keep high-current return paths away from sensitive analog inputs. Verify startup voltage, internal-regulator configuration, and the relationship between clock frequency and current draw across the intended temperature range.
Separate analog inputs from digital clocks and switching nodes, and use a continuous ground reference beneath sensitive routes. DFSDM and USB interfaces need short, symmetric connections to their source devices, while ADC inputs may require filtering that interacts with acquisition time and bandwidth. Validate crosstalk, converter reference noise, and sampling timing in hardware rather than relying only on nominal peripheral ratings.
合规信息
Compliance status was not stated in the product information available for this device. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations using the manufacturer product page or applicable declaration documents.