THS4042ID - 165MHz Dual High-Speed Amplifier | Texas Instruments
料号: THS4042ID ✓ 量产中THS4042ID 概述
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. Within the broader hierarchy of analog signal-chain ICs, an operational amplifier functions as a voltage-feedback amplifier and, in this case, as a dual high-speed amplifier. The dual configuration provides two amplifier channels in one package, simplifying board allocation while supporting common high-speed applications.
The THS4042 family's principal performance characteristics include 165 MHz bandwidth, 400 V/µs slew rate, and high output-current capability of 100 mA typical. Its C-stable operation allows use with capacitive loads without requiring an external isolation resistor in the standard application configuration. The manufacturer identifies video-line driving and ADC buffering as typical uses, applications where wide bandwidth and rapid large-signal response are more important than the low-noise characteristics emphasized in precision-only amplifiers.
The voltage-feedback topology supports conventional negative-feedback operation and is well suited to gain and signal-conditioning stages requiring predictable behavior. The C-stable architecture is particularly valuable when the amplifier drives cables, ADC input networks, or other loads that include appreciable capacitance. Its 165 MHz bandwidth provides ample headroom for high-speed instrumentation and video systems, while the 400 V/µs slew rate enables large voltage changes to be reproduced without excessive slew-rate distortion.
Typical deployments include video distribution, high-speed ADC input buffering, active filtering, test and measurement signal conditioning, and general-purpose high-speed analog interfaces. Because the THS4042ID contains two channels, both sides of a balanced signal path can be placed in the same package. This can simplify routing and reduce the number of separate amplifier packages on a board.
Designers should pay particular attention to feedback-loop stability, output swing, input and output impedance, and the power-supply requirements. The feedback network should use short, low-inductance traces, especially when operating near the device's upper bandwidth limit. Decoupling capacitors should be placed close to the supply pins, and the output load must remain compatible with the amplifier's drive capability and recommended operating conditions.
This product page combines the manufacturer's device description with practical guidance for selecting, comparing, and implementing the THS4042ID. It highlights where the dual C-stable voltage-feedback amplifier fits, distinguishes package and ordering options, and identifies the principal electrical checks to perform before releasing a high-speed analog layout.
直接替换替代料: THS4042ID ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: THS4042ID (相同外形与封装尺寸) ——差异在于 Amplifier Type, Package.
THS4042IP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
AD826ARZ
✅ 直接替换📋 参考替代料(不在目录中)
THS4042ID 最大额定值与电气特性
| Amplifier Type | Dual voltage-feedback operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 165 MHz |
| Slew Rate | 400 V/µs |
| Stability | C-stable |
| Output Current | 100 mA typical |
| Total Harmonic Distortion | -75 dBc at 1 MHz |
| 电源电压 | ±16 V/32 V |
| 封装 | 8-SOIC |
| Package Width | 3.90 mm |
| 安装类型 | Surface mount |
THS4042ID 3.90 mm 引脚配置指南
THS4042ID(3.90 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: THS4042ID.
请参阅 数据手册 以查看完整引脚配置。
典型应用
THS4042ID 适用于 6 应用s: Video-Line Driving, High-Speed ADC Input Buffering, Active Video Filtering, Test and Measurement Signal Conditioning, High-Speed Instrumentation Buffer, Communications Interface Conditioning.
Video-Line Driving
The THS4042ID fits video-line interfaces because its 165 MHz bandwidth and 400 V/µs slew rate support rapid signal transitions, while C-stable operation helps accommodate cable and connector capacitance. It can preserve signal amplitude and edge fidelity across short video distribution paths without an external isolation resistor in the standard configuration. Place the device close to the source, use short feedback paths, and verify the target impedance and maximum capacitive load. Board-level grounding and connector return paths should be controlled because long cable runs can introduce reflections beyond the amplifier's bandwidth.
推荐
High-Speed ADC Input Buffering
The dual THS4042ID is appropriate for buffering high-speed converter inputs when the system needs more drive or bandwidth than the source can provide directly. Its 165 MHz bandwidth, 400 V/µs slew rate, and 100 mA typical output current help isolate the ADC input capacitance from the signal source. The two channels can support differential or related signal paths while reducing package count. Validate settling time, kickback behavior, output swing, and stability in the complete source-converter network before production release.
推荐
Active Video Filtering
THS4042ID can implement wideband active filters where the signal path must retain predictable gain and phase performance at video-related frequencies. Its 165 MHz bandwidth provides substantial frequency range for low-pass, band-pass, and signal-conditioning networks, while the C-stable characteristic supports realistic source and load impedances. Keep the feedback network compact and use identical or closely matched components when channel-to-channel phase and gain matching matters. Validate the filter response with the actual source impedance and load because parasitic capacitance can alter the intended cutoff and peaking.
推荐
Test and Measurement Signal Conditioning
The THS4042ID is suitable for high-speed instrumentation buffers that must drive downstream cables, switches, or acquisition inputs without severe slew-rate limiting. Its 165 MHz bandwidth and 400 V/µs slew rate allow it to preserve moderate-amplitude, fast-edge signals in a measurement chain. C-stable operation is beneficial when the amplifier faces capacitive fixtures or long interconnects. Use short, controlled-impedance routing and provide local bypassing so fixture reflections and supply inductance do not dominate the measured result.
推荐
High-Speed Instrumentation Buffer
A dual THS4042ID can buffer balanced or complementary instrumentation signals when the source impedance and downstream loading would otherwise degrade amplitude or settling behavior. Its two channels provide consistent device characteristics within one 8-SOIC package, and the 165 MHz bandwidth is well suited to moderate-speed waveform acquisition. The amplifier's 100 mA typical output drive helps overcome downstream capacitance, but stability must be checked with the full cable and input network. Maintain symmetric routing where timing alignment between channels is important.
推荐
Communications Interface Conditioning
The THS4042ID can condition short-reach communications signals that require more bandwidth or output drive than a general-purpose operational amplifier supplies. Its 165 MHz gain-bandwidth product and 400 V/µs slew rate allow it to handle fast transitions while C-stable operation supports capacitive PCB and connector loads. The dual channel is useful for transmitting and receiving paths on a communications board. The designer should still evaluate protocol bandwidth, return loss, jitter sensitivity, and the complete channel impedance rather than treating the amplifier as a complete communications solution.
推荐
推荐产品汇总
工程参考数据: THS4042ID ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 8-SOIC |
| Brand | Texas Instruments |
| Amplifier Configuration | Dual |
| Gain-Bandwidth Product | 165 MHz |
| Slew Rate | 400 V/µs |
| Output Current | 100 mA typical |
| Total Harmonic Distortion | -75 dBc at 1 MHz |
| Supply Voltage | ±16 V/32 V |
| Stability | C-stable |
设计说明
Place input, output, and feedback components close to the THS4042ID and keep the feedback loop physically small. High-speed voltage-feedback amplifiers can acquire unwanted loop gain when parasitic inductance or capacitance enters the feedback path. Route each channel consistently, minimize shared return-path discontinuity between paired channels, and use a solid ground plane to reduce coupling into sensitive analog nodes.
Use the manufacturer's recommended decoupling arrangement and connect the capacitors directly to the relevant supply and ground pins. High-speed operation can expose the amplifier to supply impedance caused by long traces and inadequate bypassing, even when the external load is light. Use short, low-inductance supply connections and verify the power source can support transient current demanded by the 400 V/µs slew rate.
C-stable operation does not remove the need to evaluate the complete feedback network and load. Cable capacitance, ADC input capacitance, connector parasitics, and output impedance can alter loop stability and frequency response. Check gain-bandwidth and slew-rate requirements with the intended source and load, and avoid assuming that a generic precision-amplifier compensation method applies to this high-speed C-stable device.
合规信息
Compliance status was not stated in the manufacturer or distributor result excerpts. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations with Texas Instruments before qualification.