THS6182DWP - Low-Power ADSL/PLC Line Driver | Texas Instruments
料号: THS6182DWP ✓ 量产中THS6182DWP 概述
An ADSL line driver is an interface IC that converts a differential input signal into a high-current differential output suitable for driving copper telephone or network lines. This device belongs to the broader line-driver and interface-IC hierarchy, where signal integrity, power consumption, thermal performance, and long-term bias stability determine line-card density. The THS6182 series is particularly useful in central-office equipment where many driver channels must operate continuously in a restricted thermal envelope.
The THS6182 provides full-bias, mid-bias, low-bias, and shutdown operating modes. The manufacturer identifies 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. A user-controlled bias-current input allows the system designer to adjust operating conditions, while the architecture supports stable operation down to 1.8 mA per channel. These controls can reduce dissipation when channel activity is low without redesigning the analog signal path.
The current-feedback differential architecture is intended to maintain high linearity across the wide signal swings required by ADSL line interfaces. The device also provides low-noise operation, with the manufacturer specifying an inverting current-noise density of 3.2 nV/√Hz. Low noise helps preserve receiver sensitivity and signal-to-noise ratio in downstream circuitry. The available family information also identifies pin compatibility with EL1503C and EL1508C devices, which can simplify evaluation of alternate line-driver implementations when their electrical ratings and thermal requirements are confirmed against the manufacturer datasheet.
Typical uses include ADSL central-office line cards, splitter and aggregation equipment, power-line communication modems, telephone-network access nodes, and industrial communication interfaces. In these systems, the driver sits between a modulation or source signal stage and the transformer-coupled line. Correct operation depends on suitable supply bypassing, controlled source impedance, output-network design, and thermal management around the exposed pad of the HSOIC package.
A practical design consideration is that lower bias current reduces power dissipation but may reduce output headroom or degrade linearity at the highest demanded line amplitude. Evaluate the required peak differential output current, transformer ratio, supply tolerance, and channel duty cycle before selecting the operating mode. Keep high-current return paths short and provide adequate copper area for heat spreading so the HSOIC package maintains stable operation across the industrial temperature range.
This product page combines the THS6182DWP package and electrical identity with application guidance, operating-mode trade-offs, drop-in candidates, and engineering-focused comparison information. It is intended to help engineers qualify the device for high-density ADSL and PLC line-card designs.
直接替换替代料: THS6182DWP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: THS6182DWP (相同外形与封装尺寸) ——差异在于 Full-Bias Mode Current, Low-Bias Mode Current, Mid-Bias Mode Current, Operating Temperature Range, Package.
THS6182DW
✅ 直接替换联系询价
查看数据手册 →EL1503C
✅ 直接替换📋 参考替代料(不在目录中)
EL1508C
✅ 直接替换📋 参考替代料(不在目录中)
THS6182DWP 规格参数
| Product Type | Differential ADSL and PLC line driver |
| Architecture | Current-feedback differential line driver |
| Differential Output Configuration | 1 driver with complementary outputs |
| Supply Voltage Range | ±5 V to ±15 V |
| Full-Bias Mode Current | 11 mA per channel |
| Mid-Bias Mode Current | 7.5 mA per channel |
| Low-Bias Mode Current | 4 mA per channel |
| Shutdown Mode Current | 0.25 mA per channel |
| Stable Minimum Bias Current | 1.8 mA per channel |
| Inverting Current-Noise Density | 3.2 nV/√Hz |
| 工作温度范围 | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| 封装 | HSOIC (DWP), 20 pins |
| Package Pin Count | 20 pins |
| 安装类型 | Surface mount |
| Bias Current Adjustment | User-controlled through IADJ pin |
| Power Control Modes | Full bias, mid bias, low bias, and shutdown |
THS6182DWP 20 pins 引脚配置指南
THS6182DWP(20 pins 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: THS6182DWP.
请参阅 数据手册 以查看完整引脚配置。
典型应用
THS6182DWP 适用于 6 应用s: Full-Rate ADSL Line Cards, Power-Line Communication Interfaces, Central-Office ADSL Equipment, Telephone Network Access Equipment, Industrial Communication Interfaces, DSL Splitter and Aggregation Modules.
Full-Rate ADSL Line Cards
The THS6182DWP fits the transmit stage of a full-rate ADSL line card because it provides a current-feedback differential driver with selectable operating current. The 20-pin HSOIC DWP package supports compact channel layouts, while the ±5 V to ±15 V supply range accommodates dual-rail line-interface designs. Full-bias mode provides 11 mA per channel when maximum drive is required, whereas mid-bias and low-bias modes consume 7.5 mA and 4 mA per channel for lower-power installations. The primary engineering trade-off is output-current capability versus dissipation, so transformer turns ratio and required differential swing must be evaluated before setting the bias mode.
推荐
Power-Line Communication Interfaces
The THS6182DWP is appropriate for power-line communication interfaces that require a differential current-drive output and adjustable dissipation. Its IADJ input lets the circuit designer control bias current, and the manufacturer identifies stable operation down to 1.8 mA per channel. Low-bias operation at 4 mA per channel can reduce heat in channels with modest activity, while shutdown at 0.25 mA per channel supports inactive periods. In a PLC modem, the driver should still be matched to the coupling network, protection scheme, required bandwidth, and peak line current to avoid clipping.
推荐
Central-Office ADSL Equipment
Central-office ADSL equipment benefits from the THS6182DWP's selectable current modes because channel density directly influences heat dissipation and rack-level power use. The industrial -40 °C to +85 °C rating supports equipment intended for controlled but temperature-variable network environments. Low-bias mode reduces channel current to 4 mA per channel when line activity permits, while full-bias mode supplies 11 mA per channel for maximum drive conditions. The HSOIC DWP footprint requires effective exposed-pad heat spreading, making copper area, via density, and neighboring-component placement important parts of a reliable channel-card design.
推荐
Telephone Network Access Equipment
The THS6182DWP can be used in telephone-network access equipment where a differential line driver conditions a high-amplitude signal before transformer coupling. Its current-feedback architecture supports high linearity, and the 3.2 nV/√Hz inverting current-noise specification helps preserve receiver sensitivity in noise-sensitive signal paths. The ±5 V to ±15 V operating range supports common dual-rail line-card architectures. Designers must verify output swing, source impedance, transformer loading, and channel power dissipation at the highest required line amplitude rather than selecting bias mode solely from nominal channel count.
推荐
Industrial Communication Interfaces
The THS6182DWP's -40 °C to +85 °C industrial temperature range and low-bias controls make it suitable for industrial communication interfaces that must operate continuously in a compact enclosure. At 4 mA per channel in low-bias mode, it can reduce dissipation relative to the 11 mA per channel full-bias setting, improving thermal headroom in multi-channel systems. The design tradeoff is that lower current may not support the same output swing or distortion target as full-bias operation. Final qualification should include worst-case ambient temperature, line load, supply tolerance, and exposed-pad temperature measurement.
推荐
DSL Splitter and Aggregation Modules
Compact DSL splitter and aggregation modules can benefit from the THS6182DWP's 20-pin HSOIC DWP package and selectable current modes. A low-power channel can operate at 4 mA per channel when the downstream line and transformer do not demand maximum drive, reducing the thermal burden across densely populated modules. Shutdown mode at 0.25 mA per channel is useful when a port can be disabled during traffic control. The external transformer and line-network impedance remain important system parameters because they determine required output current and whether the selected bias mode preserves required signal amplitude and linearity.
推荐
推荐产品汇总
工程参考数据: THS6182DWP ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | THS6182DW | EL1503C | EL1508C |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | HSOIC (DWP), 20 pins | HSOIC (DWP), 20 pins | HSOIC (DWP), 20 pins | HSOIC (DWP), 20 pins |
关键差异点
- Four operating modes support both drive and power-management requirements (对比 THS6182DW)
- Manufacturer-identified pin-compatible alternatives broaden sourcing options (对比 EL1503C)
- Low-noise current-feedback operation supports receiver-sensitive line interfaces (对比 EL1508C)
设计说明
Use the HSOIC exposed pad as the principal thermal path and connect it to a low-impedance ground plane with multiple thermal vias. Estimate package dissipation from the selected bias current, supply voltage, quiescent power, and output-current dissipation before assigning channels. Validate the hottest exposed-pad and junction temperatures at maximum ambient temperature, worst-case supply, and maximum channel activity rather than relying on board-level ambient temperature alone.
Keep the driver output path short and place the external line-network or transformer connection according to the manufacturer reference layout. Provide local supply bypassing at the power pins and preserve a low-impedance return for output current. Keep sensitive receiver and feedback traces away from the driven copper path, and avoid routing unrelated digital or switching nodes beneath the analog output section.
Select the operating mode from the required differential output swing and duty cycle, not only from average dissipation. Full bias provides 11 mA per channel, mid bias 7.5 mA per channel, and low bias 4 mA per channel. Measure output clipping and linearity at the required line amplitude, then confirm the IADJ setting and supply rails remain within their manufacturer limits. Use shutdown mode at 0.25 mA per channel only when the line interface can be disconnected safely.
合规信息
The device is an industrial-temperature interface IC rather than an automotive-qualified AEC-Q100 product. Compliance declarations were not identified in the cited manufacturer product-page excerpts.