Texas Instruments

THS6182DWP - Low-Power ADSL/PLC Line Driver | Texas Instruments

MPN: THS6182DWP ✓ सक्रिय
±5 V to ±15 V Vdss 11 mA per channel Id HSOIC (DWP), 20 pins Package
न्यूनतम ऑर्डर मात्रा: 1 |

THS6182DWP अवलोकन

The Texas Instruments THS6182DWP is a low-power differential ADSL and power-line communication line driver with a 20-pin HSOIC DWP package. It is designed for full-rate ADSL systems and PLC equipment where low dissipation, high linearity, and stable bias control are important. The device supports positive and negative supply rails, with an operating supply range stated as ±5 V to ±15 V. Its bias-current architecture provides multiple operating modes for balancing output current against line-driver performance.

An ADSL line driver is an interface IC that converts a differential input signal into a high-current differential output suitable for driving copper telephone or network lines. This device belongs to the broader line-driver and interface-IC hierarchy, where signal integrity, power consumption, thermal performance, and long-term bias stability determine line-card density. The THS6182 series is particularly useful in central-office equipment where many driver channels must operate continuously in a restricted thermal envelope.

The THS6182 provides full-bias, mid-bias, low-bias, and shutdown operating modes. The manufacturer identifies 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. A user-controlled bias-current input allows the system designer to adjust operating conditions, while the architecture supports stable operation down to 1.8 mA per channel. These controls can reduce dissipation when channel activity is low without redesigning the analog signal path.

The current-feedback differential architecture is intended to maintain high linearity across the wide signal swings required by ADSL line interfaces. The device also provides low-noise operation, with the manufacturer specifying an inverting current-noise density of 3.2 nV/√Hz. Low noise helps preserve receiver sensitivity and signal-to-noise ratio in downstream circuitry. The available family information also identifies pin compatibility with EL1503C and EL1508C devices, which can simplify evaluation of alternate line-driver implementations when their electrical ratings and thermal requirements are confirmed against the manufacturer datasheet.

Typical uses include ADSL central-office line cards, splitter and aggregation equipment, power-line communication modems, telephone-network access nodes, and industrial communication interfaces. In these systems, the driver sits between a modulation or source signal stage and the transformer-coupled line. Correct operation depends on suitable supply bypassing, controlled source impedance, output-network design, and thermal management around the exposed pad of the HSOIC package.

A practical design consideration is that lower bias current reduces power dissipation but may reduce output headroom or degrade linearity at the highest demanded line amplitude. Evaluate the required peak differential output current, transformer ratio, supply tolerance, and channel duty cycle before selecting the operating mode. Keep high-current return paths short and provide adequate copper area for heat spreading so the HSOIC package maintains stable operation across the industrial temperature range.

This product page combines the THS6182DWP package and electrical identity with application guidance, operating-mode trade-offs, drop-in candidates, and engineering-focused comparison information. It is intended to help engineers qualify the device for high-density ADSL and PLC line-card designs.

के लिए ड्रॉप-इन विकल्प THS6182DWP — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं THS6182DWP (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Full-Bias Mode Current, Low-Bias Mode Current, Mid-Bias Mode Current, Operating Temperature Range, Package.

Texas Instruments
Full-Bias Mode Current: 11 mA/channel
Low-Bias Mode Current: 4 mA/channel
Mid-Bias Mode Current: 7.5 mA/channel
इसके साथ तुलना करें THS6182DWP →

THS6182DW

✅ ड्रॉप-इन
Texas Instruments
📦 HSOIC (DWP), 20 pins
Low-power differential ADSL/PLC line driver · Current-feedback differential line driver · 1/0 DSL driver · 2 driver functions · 2 bits · 20-pin SOIC · Surface mount · -40°C to +85°C

कीमत के लिए संपर्क करें

डेटाशीट देखें →

EL1503C

✅ ड्रॉप-इन
📦 HSOIC (DWP), 20 pins
Pin-compatible driver with no quantified rating difference stated in the manufacturer product page

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

EL1508C

✅ ड्रॉप-इन
📦 HSOIC (DWP), 20 pins
Pin-compatible driver with no quantified rating difference stated in the manufacturer product page

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

THS6182DWP विशेषताएं

Product Type Differential ADSL and PLC line driver
Architecture Current-feedback differential line driver
Differential Output Configuration 1 driver with complementary outputs
Supply Voltage Range ±5 V to ±15 V
Full-Bias Mode Current 11 mA per channel
Mid-Bias Mode Current 7.5 mA per channel
Low-Bias Mode Current 4 mA per channel
Shutdown Mode Current 0.25 mA per channel
Stable Minimum Bias Current 1.8 mA per channel
Inverting Current-Noise Density 3.2 nV/√Hz
ऑपरेटिंग तापमान रेंज -40 °C to +85 °C
Temperature Grade Industrial
पैकेज HSOIC (DWP), 20 pins
Package Pin Count 20 pins
माउंटिंग प्रकार Surface mount
Bias Current Adjustment User-controlled through IADJ pin
Power Control Modes Full bias, mid bias, low bias, and shutdown

THS6182DWP 20 pins पिन कॉन्फ़िगरेशन गाइड

THS6182DWP (20 pins पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।

THS6182DWP के लिए 20 pins पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: THS6182DWP.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

THS6182DWP के लिए उपयुक्त है 6 अनुप्रयोगs: Full-Rate ADSL Line Cards, Power-Line Communication Interfaces, Central-Office ADSL Equipment, Telephone Network Access Equipment, Industrial Communication Interfaces, DSL Splitter and Aggregation Modules.

🌐

Full-Rate ADSL Line Cards

The THS6182DWP fits the transmit stage of a full-rate ADSL line card because it provides a current-feedback differential driver with selectable operating current. The 20-pin HSOIC DWP package supports compact channel layouts, while the ±5 V to ±15 V supply range accommodates dual-rail line-interface designs. Full-bias mode provides 11 mA per channel when maximum drive is required, whereas mid-bias and low-bias modes consume 7.5 mA and 4 mA per channel for lower-power installations. The primary engineering trade-off is output-current capability versus dissipation, so transformer turns ratio and required differential swing must be evaluated before setting the bias mode.

🏭

Power-Line Communication Interfaces

The THS6182DWP is appropriate for power-line communication interfaces that require a differential current-drive output and adjustable dissipation. Its IADJ input lets the circuit designer control bias current, and the manufacturer identifies stable operation down to 1.8 mA per channel. Low-bias operation at 4 mA per channel can reduce heat in channels with modest activity, while shutdown at 0.25 mA per channel supports inactive periods. In a PLC modem, the driver should still be matched to the coupling network, protection scheme, required bandwidth, and peak line current to avoid clipping.

🖥️

Central-Office ADSL Equipment

Central-office ADSL equipment benefits from the THS6182DWP's selectable current modes because channel density directly influences heat dissipation and rack-level power use. The industrial -40 °C to +85 °C rating supports equipment intended for controlled but temperature-variable network environments. Low-bias mode reduces channel current to 4 mA per channel when line activity permits, while full-bias mode supplies 11 mA per channel for maximum drive conditions. The HSOIC DWP footprint requires effective exposed-pad heat spreading, making copper area, via density, and neighboring-component placement important parts of a reliable channel-card design.

🌐

Telephone Network Access Equipment

The THS6182DWP can be used in telephone-network access equipment where a differential line driver conditions a high-amplitude signal before transformer coupling. Its current-feedback architecture supports high linearity, and the 3.2 nV/√Hz inverting current-noise specification helps preserve receiver sensitivity in noise-sensitive signal paths. The ±5 V to ±15 V operating range supports common dual-rail line-card architectures. Designers must verify output swing, source impedance, transformer loading, and channel power dissipation at the highest required line amplitude rather than selecting bias mode solely from nominal channel count.

🏭

Industrial Communication Interfaces

The THS6182DWP's -40 °C to +85 °C industrial temperature range and low-bias controls make it suitable for industrial communication interfaces that must operate continuously in a compact enclosure. At 4 mA per channel in low-bias mode, it can reduce dissipation relative to the 11 mA per channel full-bias setting, improving thermal headroom in multi-channel systems. The design tradeoff is that lower current may not support the same output swing or distortion target as full-bias operation. Final qualification should include worst-case ambient temperature, line load, supply tolerance, and exposed-pad temperature measurement.

📡

DSL Splitter and Aggregation Modules

Compact DSL splitter and aggregation modules can benefit from the THS6182DWP's 20-pin HSOIC DWP package and selectable current modes. A low-power channel can operate at 4 mA per channel when the downstream line and transformer do not demand maximum drive, reducing the thermal burden across densely populated modules. Shutdown mode at 0.25 mA per channel is useful when a port can be disabled during traffic control. The external transformer and line-network impedance remain important system parameters because they determine required output current and whether the selected bias mode preserves required signal amplitude and linearity.

What is THS6182DWP?
THS6182DWP is a Texas Instruments low-power differential ADSL and PLC line driver packaged in a 20-pin HSOIC DWP package. It is intended for full-rate ADSL equipment and power-line communication interfaces. According to the Texas Instruments product page, the device uses a current-feedback differential architecture, supports user-controlled bias current, and includes multiple power-control modes for balancing dissipation against line-driver performance.
What are the key specifications of THS6182DWP that engineers should know?
The THS6182DWP operates from ±5 V to ±15 V and uses four bias-control modes: 11 mA per channel for full bias, 7.5 mA per channel for mid bias, 4 mA per channel for low bias, and 0.25 mA per channel for shutdown. Texas Instruments specifies an industrial temperature range of -40 °C to +85 °C, a 20-pin HSOIC package, and 3.2 nV/√Hz inverting current-noise density.
Where can I download the THS6182DWP datasheet PDF?
The official THS6182 product page provides access to the Texas Instruments data sheet and supporting technical documentation. The device family is documented as a low-power dissipation ADSL line driver. Use the manufacturer page at https://www.ti.com/product/THS6182 for the current revision, then use the ordering information to confirm that THS6182DWP denotes the 20-pin HSOIC DWP package.
Where can I find the THS6182DWP pinout?
The THS6182DWP pinout and pin functions are shown in the pin-configuration section of the manufacturer data sheet. The orderable device has 20 pins in an HSOIC DWP package, including power connections, differential inputs, complementary outputs, bias-control functions, and a thermal exposed pad. Use the manufacturer pin-description table when assigning PCB nets and confirming exposed-pad grounding.
How much power does THS6182DWP consume in each bias mode?
The THS6182DWP can be placed into full-bias, mid-bias, low-bias, or shutdown operation. Texas Instruments specifies 11 mA per channel in full bias, 7.5 mA per channel in mid bias, 4 mA per channel in low bias, and 0.25 mA per channel in shutdown. These figures are bias currents rather than total board power, so actual dissipation also depends on supply voltage, output swing, load current, and channel activity.
Can THS6182DWP be used for power-line communication equipment?
Yes, the THS6182DWP is suitable for power-line communication line-driver stages where low dissipation and controlled output current are needed. Its differential current-feedback architecture, selectable bias modes, and IADJ control support line-interface designs requiring different levels of output drive. The external transformer, coupling network, protection elements, and signal bandwidth must still be designed for the selected PLC operating band.
When should I choose THS6182DWP over THS6182DW?
Choose THS6182DWP when the assembled PCB is intended for the 20-pin HSOIC DWP package and industrial temperature range. The manufacturer lists THS6182DW as a related 20-pin device, but the mechanical package option must be checked before treating it as a direct board-level substitution. THS6182DWP is the appropriate selection when the DWP footprint and its exposed-pad layout match the PCB.
What is the difference between THS6182DWP and THS6182DWPR?
THS6182DWP identifies the 20-pin HSOIC DWP device configuration, while THS6182DWPR identifies the tape-and-reel order form associated with the DW package option. The family-level electrical function remains a low-power ADSL line driver. Because reel and tape designations primarily affect order packaging, engineers should compare the actual package suffix and exposed-pad requirements before treating the two orderable MPNs as separate circuit designs.
What is the best drop-in replacement for THS6182DWP?
The Texas Instruments product page identifies pin compatibility with EL1503C and EL1508C, making them the most relevant candidates to evaluate for a replacement. A valid drop-in decision still requires matching the 20-pin footprint, exposed-pad arrangement, supply rating, output-current capability, bias-control implementation, and thermal limits. Use the manufacturer data sheets for both devices before approving a substitution.
Can EL1503C replace THS6182DWP?
EL1503C is identified by Texas Instruments as pin compatible with THS6182, so it is a candidate for THS6182DWP replacement. The devices must still be checked for equivalent supply range, bias modes, output-drive capability, and thermal performance at the selected operating point. The compatibility statement supports footprint evaluation, but circuit-level qualification remains necessary for production use.
Can EL1508C replace THS6182DWP?
EL1508C is also identified as pin compatible with THS6182 and can be considered for THS6182DWP replacement. Compare its output stage, bias-control method, maximum differential swing, quiescent current, and thermal limits against the original design. The manufacturer data sheet should be used to confirm compatibility across the required supply voltage, line frequency, and ambient temperature.
Where can I buy THS6182DWP online?
Use the Request a Quote form on this page to request THS6182DWP availability, commercial terms, and lead time for the exact 20-pin HSOIC DWP orderable device. The form lets engineers confirm current supply without relying on a stale catalog price. For design qualification, obtain the manufacturer data sheet and the exact package drawing from the official Texas Instruments product page.
What is the price of THS6182DWP?
The current commercial price for THS6182DWP should be requested through the Request a Quote form on this page. Submit the exact MPN, required quantity, shipment destination, and target delivery date so the quote reflects the correct DWP package and order terms. Requesting a formal quote avoids presenting an outdated catalog price as current inventory or lead-time information.
What is the lead time and stock status for THS6182DWP?
Request the current stock position, minimum order quantity, and lead time for THS6182DWP through the Request a Quote form on this page. Lead time can depend on package demand, production scheduling, and shipment quantity, so it should be confirmed for the exact orderable MPN rather than inferred from a generic product-page status. Include your required schedule in the request for an actionable response.
Is THS6182DWP suitable for industrial ADSL line cards?
The THS6182DWP is rated for an industrial temperature range of -40 °C to +85 °C and is identified as an ADSL and PLC line driver. It is suitable for industrial line-card designs requiring differential line-drive capability and selectable bias modes. Final suitability depends on line amplitude, transformer topology, channel density, ambient conditions, and the thermal design of the HSOIC exposed pad.
Does THS6182DWP include thermal protection?
The THS6182DWP must be operated within the limits defined by its manufacturer data sheet, including its supply, bias-current, output, and temperature ratings. Its 20-pin HSOIC package uses an exposed pad that requires careful PCB heat spreading to dissipate package power effectively. Use the manufacturer's maximum dissipation and junction-temperature information when establishing the allowable channel count and copper area.

के लिए इंजीनियरिंग संदर्भ डेटा THS6182DWP — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose THS6182DWP for a 20-pin HSOIC ADSL or PLC line-driver design that needs selectable dissipation and user-controlled bias current. Its 11, 7.5, 4, and 0.25 mA per-channel modes allow the circuit to balance output drive against thermal load. THS6182DW is the closely related order option to evaluate when the manufacturer package designation matches the PCB, but engineers should verify the exact mechanical suffix rather than assuming a reel or temperature code is electrically identical. EL1503C and EL1508C are useful replacement candidates because Texas Instruments identifies pin compatibility with THS6182; however, confirm output-current capability, supply range, bias implementation, distortion, and thermal limits against the manufacturer data sheets before approving either part. For production designs, prioritize exposed-pad layout, transformer and line-network compatibility, worst-case output swing, and the operating temperature required by the target ADSL central-office, PLC, or industrial communication equipment.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद THS6182DW EL1503C EL1508C
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package HSOIC (DWP), 20 pins HSOIC (DWP), 20 pins HSOIC (DWP), 20 pins HSOIC (DWP), 20 pins

मुख्य विशेषताएँ

  • Four operating modes support both drive and power-management requirements (बनामTHS6182DW)
  • Manufacturer-identified pin-compatible alternatives broaden sourcing options (बनामEL1503C)
  • Low-noise current-feedback operation supports receiver-sensitive line interfaces (बनामEL1508C)

डिज़ाइन नोट्स

Use the HSOIC exposed pad as the principal thermal path and connect it to a low-impedance ground plane with multiple thermal vias. Estimate package dissipation from the selected bias current, supply voltage, quiescent power, and output-current dissipation before assigning channels. Validate the hottest exposed-pad and junction temperatures at maximum ambient temperature, worst-case supply, and maximum channel activity rather than relying on board-level ambient temperature alone.

Keep the driver output path short and place the external line-network or transformer connection according to the manufacturer reference layout. Provide local supply bypassing at the power pins and preserve a low-impedance return for output current. Keep sensitive receiver and feedback traces away from the driven copper path, and avoid routing unrelated digital or switching nodes beneath the analog output section.

Select the operating mode from the required differential output swing and duty cycle, not only from average dissipation. Full bias provides 11 mA per channel, mid bias 7.5 mA per channel, and low bias 4 mA per channel. Measure output clipping and linearity at the required line amplitude, then confirm the IADJ setting and supply rails remain within their manufacturer limits. Use shutdown mode at 0.25 mA per channel only when the line interface can be disconnected safely.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The device is an industrial-temperature interface IC rather than an automotive-qualified AEC-Q100 product. Compliance declarations were not identified in the cited manufacturer product-page excerpts.

डेटा सत्यापन तिथि: 2026-11-20 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

THS6182DWP datasheet THS6182DWP pinout THS6182DWP datasheet pdf THS6182DWP specifications THS6182DWP HSOIC DWP THS6182DWP ADSL line driver THS6182DWP PLC driver THS6182DWP replacement THS6182DWP equivalent THS6182DWP price THS6182DWP stock Texas Instruments THS6182DWP

संबंधित कंपोनेंट्स और शब्द

Texas Instruments THS6182DWP THS6182DW EL1503C EL1508C ADSL line driver PLC line driver differential driver current-feedback amplifier line driver IC interface IC semiconductor HSOIC DWP 20-pin surface-mount package power supply bias current IADJ pin shutdown mode output noise inverting current-noise density central-office line card power-line communication industrial temperature grade
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें