THS6182DWP - Low-Power ADSL/PLC Line Driver | Texas Instruments
N.º de pieza: THS6182DWP ✓ ActivoTHS6182DWP Descripción general
An ADSL line driver is an interface IC that converts a differential input signal into a high-current differential output suitable for driving copper telephone or network lines. This device belongs to the broader line-driver and interface-IC hierarchy, where signal integrity, power consumption, thermal performance, and long-term bias stability determine line-card density. The THS6182 series is particularly useful in central-office equipment where many driver channels must operate continuously in a restricted thermal envelope.
The THS6182 provides full-bias, mid-bias, low-bias, and shutdown operating modes. The manufacturer identifies 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. A user-controlled bias-current input allows the system designer to adjust operating conditions, while the architecture supports stable operation down to 1.8 mA per channel. These controls can reduce dissipation when channel activity is low without redesigning the analog signal path.
The current-feedback differential architecture is intended to maintain high linearity across the wide signal swings required by ADSL line interfaces. The device also provides low-noise operation, with the manufacturer specifying an inverting current-noise density of 3.2 nV/√Hz. Low noise helps preserve receiver sensitivity and signal-to-noise ratio in downstream circuitry. The available family information also identifies pin compatibility with EL1503C and EL1508C devices, which can simplify evaluation of alternate line-driver implementations when their electrical ratings and thermal requirements are confirmed against the manufacturer datasheet.
Typical uses include ADSL central-office line cards, splitter and aggregation equipment, power-line communication modems, telephone-network access nodes, and industrial communication interfaces. In these systems, the driver sits between a modulation or source signal stage and the transformer-coupled line. Correct operation depends on suitable supply bypassing, controlled source impedance, output-network design, and thermal management around the exposed pad of the HSOIC package.
A practical design consideration is that lower bias current reduces power dissipation but may reduce output headroom or degrade linearity at the highest demanded line amplitude. Evaluate the required peak differential output current, transformer ratio, supply tolerance, and channel duty cycle before selecting the operating mode. Keep high-current return paths short and provide adequate copper area for heat spreading so the HSOIC package maintains stable operation across the industrial temperature range.
This product page combines the THS6182DWP package and electrical identity with application guidance, operating-mode trade-offs, drop-in candidates, and engineering-focused comparison information. It is intended to help engineers qualify the device for high-density ADSL and PLC line-card designs.
Alternativas directas para THS6182DWP — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con THS6182DWP (mismo factor de forma y huella) — difiere en Full-Bias Mode Current, Low-Bias Mode Current, Mid-Bias Mode Current, Operating Temperature Range, Package.
THS6182DW
✅ Sustitución directaConsulte el precio
Ver hoja de datos →EL1503C
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
EL1508C
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
THS6182DWP Especificaciones
| Product Type | Differential ADSL and PLC line driver |
| Architecture | Current-feedback differential line driver |
| Differential Output Configuration | 1 driver with complementary outputs |
| Supply Voltage Range | ±5 V to ±15 V |
| Full-Bias Mode Current | 11 mA per channel |
| Mid-Bias Mode Current | 7.5 mA per channel |
| Low-Bias Mode Current | 4 mA per channel |
| Shutdown Mode Current | 0.25 mA per channel |
| Stable Minimum Bias Current | 1.8 mA per channel |
| Inverting Current-Noise Density | 3.2 nV/√Hz |
| Rango de temperatura de funcionamiento | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| Encapsulado | HSOIC (DWP), 20 pins |
| Package Pin Count | 20 pins |
| Tipo de montaje | Surface mount |
| Bias Current Adjustment | User-controlled through IADJ pin |
| Power Control Modes | Full bias, mid bias, low bias, and shutdown |
Guía de configuración de pines de THS6182DWP 20 pins
Configuración de pines para THS6182DWP (encapsulado 20 pins). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para THS6182DWP.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
THS6182DWP es adecuado para 6 aplicacións: Full-Rate ADSL Line Cards, Power-Line Communication Interfaces, Central-Office ADSL Equipment, Telephone Network Access Equipment, Industrial Communication Interfaces, DSL Splitter and Aggregation Modules.
Full-Rate ADSL Line Cards
The THS6182DWP fits the transmit stage of a full-rate ADSL line card because it provides a current-feedback differential driver with selectable operating current. The 20-pin HSOIC DWP package supports compact channel layouts, while the ±5 V to ±15 V supply range accommodates dual-rail line-interface designs. Full-bias mode provides 11 mA per channel when maximum drive is required, whereas mid-bias and low-bias modes consume 7.5 mA and 4 mA per channel for lower-power installations. The primary engineering trade-off is output-current capability versus dissipation, so transformer turns ratio and required differential swing must be evaluated before setting the bias mode.
Recomendado
Power-Line Communication Interfaces
The THS6182DWP is appropriate for power-line communication interfaces that require a differential current-drive output and adjustable dissipation. Its IADJ input lets the circuit designer control bias current, and the manufacturer identifies stable operation down to 1.8 mA per channel. Low-bias operation at 4 mA per channel can reduce heat in channels with modest activity, while shutdown at 0.25 mA per channel supports inactive periods. In a PLC modem, the driver should still be matched to the coupling network, protection scheme, required bandwidth, and peak line current to avoid clipping.
Recomendado
Central-Office ADSL Equipment
Central-office ADSL equipment benefits from the THS6182DWP's selectable current modes because channel density directly influences heat dissipation and rack-level power use. The industrial -40 °C to +85 °C rating supports equipment intended for controlled but temperature-variable network environments. Low-bias mode reduces channel current to 4 mA per channel when line activity permits, while full-bias mode supplies 11 mA per channel for maximum drive conditions. The HSOIC DWP footprint requires effective exposed-pad heat spreading, making copper area, via density, and neighboring-component placement important parts of a reliable channel-card design.
Recomendado
Telephone Network Access Equipment
The THS6182DWP can be used in telephone-network access equipment where a differential line driver conditions a high-amplitude signal before transformer coupling. Its current-feedback architecture supports high linearity, and the 3.2 nV/√Hz inverting current-noise specification helps preserve receiver sensitivity in noise-sensitive signal paths. The ±5 V to ±15 V operating range supports common dual-rail line-card architectures. Designers must verify output swing, source impedance, transformer loading, and channel power dissipation at the highest required line amplitude rather than selecting bias mode solely from nominal channel count.
Recomendado
Industrial Communication Interfaces
The THS6182DWP's -40 °C to +85 °C industrial temperature range and low-bias controls make it suitable for industrial communication interfaces that must operate continuously in a compact enclosure. At 4 mA per channel in low-bias mode, it can reduce dissipation relative to the 11 mA per channel full-bias setting, improving thermal headroom in multi-channel systems. The design tradeoff is that lower current may not support the same output swing or distortion target as full-bias operation. Final qualification should include worst-case ambient temperature, line load, supply tolerance, and exposed-pad temperature measurement.
Recomendado
DSL Splitter and Aggregation Modules
Compact DSL splitter and aggregation modules can benefit from the THS6182DWP's 20-pin HSOIC DWP package and selectable current modes. A low-power channel can operate at 4 mA per channel when the downstream line and transformer do not demand maximum drive, reducing the thermal burden across densely populated modules. Shutdown mode at 0.25 mA per channel is useful when a port can be disabled during traffic control. The external transformer and line-network impedance remain important system parameters because they determine required output current and whether the selected bias mode preserves required signal amplitude and linearity.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para THS6182DWP — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | THS6182DW | EL1503C | EL1508C |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | HSOIC (DWP), 20 pins | HSOIC (DWP), 20 pins | HSOIC (DWP), 20 pins | HSOIC (DWP), 20 pins |
Diferenciadores clave
- Four operating modes support both drive and power-management requirements (frente a THS6182DW)
- Manufacturer-identified pin-compatible alternatives broaden sourcing options (frente a EL1503C)
- Low-noise current-feedback operation supports receiver-sensitive line interfaces (frente a EL1508C)
Notas de diseño
Use the HSOIC exposed pad as the principal thermal path and connect it to a low-impedance ground plane with multiple thermal vias. Estimate package dissipation from the selected bias current, supply voltage, quiescent power, and output-current dissipation before assigning channels. Validate the hottest exposed-pad and junction temperatures at maximum ambient temperature, worst-case supply, and maximum channel activity rather than relying on board-level ambient temperature alone.
Keep the driver output path short and place the external line-network or transformer connection according to the manufacturer reference layout. Provide local supply bypassing at the power pins and preserve a low-impedance return for output current. Keep sensitive receiver and feedback traces away from the driven copper path, and avoid routing unrelated digital or switching nodes beneath the analog output section.
Select the operating mode from the required differential output swing and duty cycle, not only from average dissipation. Full bias provides 11 mA per channel, mid bias 7.5 mA per channel, and low bias 4 mA per channel. Measure output clipping and linearity at the required line amplitude, then confirm the IADJ setting and supply rails remain within their manufacturer limits. Use shutdown mode at 0.25 mA per channel only when the line interface can be disconnected safely.
Información de cumplimiento
The device is an industrial-temperature interface IC rather than an automotive-qualified AEC-Q100 product. Compliance declarations were not identified in the cited manufacturer product-page excerpts.