TLV07IDR - 36V Precision Rail-to-Rail Op Amp | Texas Instruments
料号： TLV07IDR ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $0.9256 | $0.93 |
| 10 | $0.85 | $8.50 |
| 100 | $0.72 | $72.00 |
| 500 | $0.61 | $305.00 |
| 1,000 | $0.54 | $540.00 |
TLV07IDR 概述
A precision operational amplifier is a voltage-feedback analog IC that amplifies the difference between two input voltages while using negative feedback to set the closed-loop gain. The TLV07 belongs to the operational amplifier hierarchy, which sits within analog signal-chain ICs and broader semiconductor devices. It is intended for instrumentation, buffering, signal conditioning, and precision control paths that require low offset and low noise.
The TLV07 combines a wide 36 V operating range with rail-to-rail output capability, allowing the output to approach the supply rails under suitable load conditions. Its 1 MHz gain-bandwidth product supports moderate-bandwidth closed-loop amplifier designs, while the 0.7 V/µs slew rate is useful for signals requiring controlled transitions. The low-noise architecture is particularly relevant when small sensor, measurement, or control signals must be amplified without adding excessive broadband noise.
The input common-mode range and output-swing behavior must be checked against the actual supply and load conditions. In designs using high supply voltages, input-current limiting is important: the manufacturer data recommends limiting input current to 10 mA. The 8-SOIC package facilitates conventional surface-mount assembly, while the exposed thermal considerations depend on the board footprint and operating dissipation rather than the package alone.
Typical uses include industrial instrumentation, low-level sensor amplification, analog measurement chains, precision buffer stages, process-control interfaces, and low-noise signal conditioning. The TLV07IDR is preferable where a single op amp and a 36 V-capable supply simplify the design, but application engineers should confirm input range, output swing, noise, stability, and load-drive requirements against the datasheet and their specific operating conditions.
For PCB implementation, place decoupling capacitors close to the supply pins and route feedback and signal paths away from switching nodes. Stable feedback-network component values and careful grounding help preserve precision performance. This page combines manufacturer information, distributor availability, package details, pricing context, and design guidance for faster engineering evaluation.
直接替换替代料： TLV07IDR ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
快速对比工具——选择替代料号进行并排对比：
TLV07IDR
✅ 直接替换✓ 有现货
$0.54 / 个
查看数据手册 →TLV07IP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
TLV07IPDR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
TLV07IDGTR
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
TLV07IN
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
TLV07IDR 最大额定值与电气特性
| Product Type | Precision operational amplifier |
| Number of Circuits | 1 circuit |
| Supply Voltage Range, Single | 4.5 V to 36 V |
| Supply Voltage Range, Dual | ±2.25 V to ±18 V |
| Maximum Supply Voltage | 36 V |
| Rail-to-Rail Output | Yes |
| Input Offset Voltage, Typical | 20 µV |
| Input Offset Voltage, Maximum | 150 µV |
| Input Offset Drift, Typical | 1 µV/°C |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 0.7 V/µs |
| 工作温度范围 | -40°C to +125°C |
| 封装 | 8-SOIC, 0.154 inch width, 3.90 mm width |
| 安装类型 | Surface Mount |
| Amplifier Type | General-purpose precision amplifier |
| Input Current Limit Recommendation | 10 mA maximum recommended application limit |
TLV07IDR 8-soic, 0.154 inch width, 3.90 mm width 引脚配置指南
TLV07IDR（8-soic, 0.154 inch width, 3.90 mm width 封装）的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据： TLV07IDR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TLV07IDR 适用于 6 应用s: Industrial Sensor Signal Conditioning, 24 V Process-Control Interfaces, Precision Analog Measurement, Low-Noise Buffering, Data-Acquisition Front Ends, Audio and Low-Level Signal Paths.
Industrial Sensor Signal Conditioning
The TLV07IDR fits industrial sensor signal conditioning because it combines a typical 20 µV input offset with a 1 µV/°C typical offset drift and a 36 V maximum supply. It can amplify low-level differential sensor signals in 24 V-class measurement systems while keeping the output swing closer to the supply rails. The device’s 1 MHz gain-bandwidth product is adequate for many moderate-bandwidth instrumentation stages. Use stable feedback values, check the input common-mode range, and protect the inputs from transients. The performance benefit is reduced input-referred offset error compared with a general-purpose amplifier, while the tradeoff is a supply range and bias requirements that must be verified against the sensor source.
推荐
24 V Process-Control Interfaces
The TLV07IDR is useful in 24 V process-control interfaces because its verified single-supply operating range extends to 36 V and its output is rail-to-rail. It can buffer or amplify controller signals where the input signal is smaller than the available control-rail span. The 0.7 V/µs slew rate provides controlled transitions for many analog control paths, while the typical 20 µV offset helps preserve small command signals. Input protection remains important because industrial wiring can introduce transients, and the 10 mA application input-current recommendation should be enforced. Verify common-mode range and load current before selecting the feedback topology.
推荐
Precision Analog Measurement
For precision analog measurement, the TLV07IDR provides a low-offset single op amp in an 8-SOIC package. The typical 20 µV offset and 1 µV/°C drift are concrete benefits when the measured signal is small and temperature variation matters. Its 1 MHz gain-bandwidth product can support measurement-bandwidth requirements, but the system’s resistor noise, source impedance, input bias current, and amplifier noise must be included in the error budget. A low-noise device such as the NE5532D may be preferable where noise dominates, while TLV07IDR is appropriate where supply range and precision offset are more important.
推荐
Low-Noise Buffering
TLV07IDR can provide a unity-gain buffer stage for low-level analog signals because it is specified as a precision, low-noise operational amplifier. Buffering prevents a high-impedance source from being loaded by the next stage and can isolate downstream circuitry from source impedance effects. The 1 MHz gain-bandwidth product and 0.7 V/µs slew rate support many moderate-speed buffers, but capacitive loading and feedback layout can affect stability. Keep the buffer input and output paths short, use a defined ground reference, and verify the load capacitance against the manufacturer’s guidance. The advantage is integration of precision offset control and wide supply operation in a standard 8-SOIC footprint.
推荐
Data-Acquisition Front Ends
The TLV07IDR can serve as the first active stage of a data-acquisition front end when the input signal is differential and requires amplification before digitization. Its typical 20 µV offset and 1 µV/°C drift help limit systematic error, while the 36 V maximum supply supports higher-voltage acquisition systems. The 1 MHz bandwidth is sufficient for many multiplexed or sensor-level signals but may be insufficient for wideband sampling chains. Designers should account for common-mode range, input capacitance, source impedance, settling time, and ADC driver requirements. A dedicated low-noise amplifier may be better when the ADC requires substantially higher bandwidth or lower integrated noise.
推荐
Audio and Low-Level Signal Paths
TLV07IDR is a candidate for low-level audio and instrumentation signal paths where the system needs a precision amplifier with rail-to-rail output on a higher-voltage supply. The rail-to-rail output can provide more available signal swing in single-supply circuitry, and the typical 20 µV offset helps reduce DC error in gain stages. However, the supplied verified data does not state a numeric noise-density specification, so audio designers should confirm the complete input-referred noise and bandwidth requirements from the manufacturer datasheet. The 1 MHz bandwidth is not a substitute for a dedicated wideband audio amplifier. Use short, quiet signal paths and suitable coupling or filtering stages.
推荐
推荐产品汇总
工程参考数据： TLV07IDR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TLV07IDR | TLV07IP | TLV07IPDR | TLV07IDGTR | TLV07IN |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same, suffix verification required | 8-SOIC - same, suffix verification required | 8-SOIC - same, suffix verification required | 8-SOIC - same, suffix verification required |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Precision operational amplifier | Precision operational amplifier | TLV07 family amplifier; exact ordering variant requires datasheet | TLV07 family amplifier; exact ordering variant requires datasheet | TLV07 family amplifier; exact ordering variant requires datasheet | TLV07 family amplifier; exact ordering variant requires datasheet |
关键差异点
- Higher supply-voltage capability than typical low-voltage precision amplifiers （对比 LM358N)
- Precision offset characteristics for low-level amplification （对比 LM358N)
- Rail-to-rail output for improved single-supply signal swing （对比 LM358N)
设计说明
Place the supply bypass capacitors close to the TLV07IDR power pins and return their ground ends through a low-impedance path. Keep the feedback resistors and signal traces short, and avoid routing precision input lines beneath or beside switching-conductor paths. The 36 V supply capability does not remove the need for normal decoupling; high supply voltage can increase coupling and fault-energy concerns. Confirm the package pinout against the official TLV07 datasheet before finalizing the PCB because the supplied search snippets do not provide authoritative pin assignments.
Do not assume that rail-to-rail output means the input common-mode range is also rail-to-rail. The verified data explicitly identifies rail-to-rail output only. Check the datasheet input common-mode limits, output swing, load current, and stability conditions for the intended feedback network. Also enforce the manufacturer recommendation to limit application input current to 10 mA, particularly during power sequencing or fault conditions when an external source could back-feed the op amp.
For small-signal measurement, begin by calculating the complete error budget rather than relying only on the 20 µV typical input offset. Include resistor tolerance and noise, source impedance, input bias current, temperature drift, output loading, and the selected closed-loop bandwidth. The verified 1 MHz gain-bandwidth product and 0.7 V/µs slew rate define useful performance limits, but settling and noise must be evaluated for the actual gain, feedback values, source impedance, and load.
合规信息
The supplied verified data does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for TLV07IDR. Check the current manufacturer product page and applicable quality documentation before making a compliance claim.
