Texas Instruments

TLV2760IP - 500kHz RRIO Op Amp with Shutdown | Texas Instruments

料号: TLV2760IP ✓ 量产中
3.6 V Vdss 20 microamperes typical Id 8-pin PDIP, 0.300 inch pitch Package
最小起订量: 1 |

TLV2760IP 概述

Texas Instruments TLV2760IP is a single-supply, rail-to-rail input and output operational amplifier with shutdown, 500 kHz gain-bandwidth product, and operation down to 1.8 V. It is packaged in an 8-pin PDIP and intended for low-voltage, low-power signal-conditioning systems. The family combines rail-to-rail input and output operation, low quiescent current, and shutdown control in a through-hole package.

An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2760 belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, micropower amplifiers, and general-purpose analog ICs. Rail-to-rail input operation allows the input common-mode range to extend close to the supply rails, while rail-to-rail output operation improves output swing in low-voltage systems.

The TLV2760 family provides 500 kHz bandwidth from approximately 20 microamperes of quiescent current and supports operation down to 1.8 V. The TLV2760IP is the high-offset-voltage member of the family, with a listed offset-voltage rating of 3500 microvolts. Its shutdown function allows a system designer to reduce supply current when the amplifier is not required, which is valuable in portable and battery-powered equipment.

The low operating voltage and rail-to-rail behavior make the device suitable for sensor interfaces, transducers, battery-powered instrumentation, audio signal paths, and embedded control systems. Its 500 kHz bandwidth provides enough bandwidth for general-purpose feedback and error-amplifier networks without the higher power and noise associated with much faster amplifiers.

The 8-pin PDIP package supports through-hole assembly and prototype rework, while its exposed lead spacing follows the standard 8-pin PDIP footprint. Designers should verify the shutdown-logic polarity, input bias behavior, output swing, and stability requirements against the manufacturer datasheet before using the amplifier near supply limits.

This page combines the TLV2760IP electrical characteristics, lifecycle information, package data, sourcing workflow, and practical replacement guidance. It also highlights the distinctions among TLV276x offset-voltage options so engineers can select a pin-compatible family member without overlooking offset or shutdown requirements.

直接替换替代料: TLV2760IP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: TLV2760IP (相同外形与封装尺寸) ——差异在于 Amplifier Type, Number of Circuits, Package.

Texas Instruments
Amplifier Type: General-purpose rail-to-rail input/output
Number of Circuits: 1
Package: 8-pin PDIP (P)
对比 TLV2760IP →

TLV2761IP

✅ 直接替换
Texas Instruments
📦 8-pin PDIP (P)
Single operational amplifier · Texas Instruments · 3.6 V · 500 kHz · 20 µA · 10.2 mA · Rail-to-rail

联系询价

查看数据手册 →

TLV2762IP

✅ 直接替换
Texas Instruments
📦 8-pin PDIP (P)
Dual operational amplifier · 2 channels · 1.8 V · 3.6 V · 20 uA per channel · 10 nA per channel · 500 kHz · Rail-to-rail

联系询价

查看数据手册 →

TLV2763IP

✅ 直接替换
📦 8-pin PDIP (P)
Retains the 8-pin PDIP footprint and shutdown-equipped family architecture, with a different offset-voltage class from the TLV2760IP.

📋 参考替代料(不在目录中)

TLV2760IP 最大额定值与电气特性

Amplifier Type Single operational amplifier
Number of Circuits 1 circuit
Nominal Supply Voltage 3.6 V
Gain-Bandwidth Product 500 kHz
静态电流 20 microamperes typical
Input Rail-to-Rail Yes
Output Rail-to-Rail Yes
Shutdown Control Yes
Offset Voltage 3500 microvolts
Operating Temperature Class Industrial temperature range
封装 8-pin PDIP, 0.300 inch pitch
安装类型 Through-hole
输出类型 Rail-to-rail
Product Category General-purpose amplifier

TLV2760IP 8-pin pdip, 0.300 inch pitch 引脚配置指南

TLV2760IP(8-pin pdip, 0.300 inch pitch 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

TLV2760IP 的 8-pin pdip, 0.300 inch pitch 封装引脚图

暂无详细引脚数据: TLV2760IP.

请参阅 数据手册 以查看完整引脚配置。

典型应用

TLV2760IP 适用于 6 应用s: Battery-Powered Sensor Signal Conditioning, Portable Instrumentation, Low-Voltage Audio Preamplifier, Industrial Control Interface, Transducer and Bridge-Signal Amplifier, Embedded Control Signal Conditioning.

🔋

Battery-Powered Sensor Signal Conditioning

The TLV2760IP fits low-voltage sensor front ends because it operates down to 1.8 V, supports rail-to-rail input and output, and uses approximately 20 microamperes of quiescent current. It can amplify a sensor signal close to either supply rail before conversion or sampling. The shutdown function reduces current demand when sensing is intermittent. Because this TLV2760 version has a 3500 microvolt offset-voltage rating, it is most appropriate when the downstream system can tolerate that offset or when offset is corrected through calibration.

📱

Portable Instrumentation

Portable measurement equipment benefits from the TLV2760IP's low 1.8 V minimum operating voltage and approximately 20 microamperes supply demand. Its 500 kHz gain-bandwidth product is suitable for conditioning moderate-frequency signals without requiring a high-speed amplifier. Rail-to-rail input capability preserves measurement range near the supply limits, while rail-to-rail output improves drive into a following converter or instrumentation stage. Verify the 3500 microvolt offset specification against the required measurement resolution.

🎧

Low-Voltage Audio Preamplifier

The TLV2760IP can provide input and output swing close to the rails in a low-voltage audio preamplifier, which helps preserve headroom in portable playback systems. Its 500 kHz bandwidth covers common audio-band signal conditioning, while approximately 20 microamperes of quiescent current limits continuous power use. The shutdown control can disable the amplifier between active intervals. For high-fidelity designs, compare the device's offset, noise, and output-drive characteristics with the selected audio requirements.

🏭

Industrial Control Interface

The TLV2760IP is applicable to low-voltage industrial interface circuits that require rail-to-rail input operation, such as conditioning a controller signal or driving a slow analog input. Its approximately 20 microamperes quiescent current supports distributed low-power sensing, and the shutdown function permits controlled operating states. The industrial temperature-range designation supports industrial environments, but designers should verify absolute maximum ratings, input bias current, and offset stability for the specific control loop.

🎛️

Transducer and Bridge-Signal Amplifier

For low-level transducer signals, the TLV2760IP's rail-to-rail input and output behavior can be useful when the transducer operates close to the available supply range. The 500 kHz gain-bandwidth product supports practical audio-band and instrumentation bandwidth, and the shutdown function allows the amplifier to remain off outside measurement intervals. Check the TLV2760IP's 3500 microvolt offset rating, input bias current, and noise against the transducer's sensitivity before choosing the final gain configuration.

🧩

Embedded Control Signal Conditioning

The TLV2760IP can condition sensor, feedback, or reference signals around a low-voltage embedded controller. Its 500 kHz bandwidth supports general-purpose amplifier networks, and operation down to 1.8 V allows use with low-energy supply rails. Rail-to-rail inputs reduce common-mode headroom concerns, while the shutdown input permits power-state management. Ensure the controller's ADC input range, amplifier stability with the selected feedback network, and settling requirements are satisfied before deployment.

What is the TLV2760IP?
The TLV2760IP is a single, general-purpose operational amplifier with rail-to-rail input and output, a 500 kHz gain-bandwidth product, and a shutdown function. According to the Texas Instruments TLV2760 product page, it operates from a 1.8 V minimum supply and is offered in an 8-pin PDIP package. It is intended for low-voltage, low-power signal conditioning where rail-to-rail operation is useful.
What is the operating voltage of TLV2760IP?
The TLV2760IP operates down to a 1.8 V supply, making it suitable for low-voltage systems. Texas Instruments describes the device as a 3.6 V, 500 kHz, rail-to-rail operational amplifier with shutdown, while the family specification supports operation from 1.8 V. Use the manufacturer datasheet to confirm the exact maximum supply voltage before finalizing a circuit.
What is the gain-bandwidth product of TLV2760IP?
The TLV2760IP has a 500 kHz gain-bandwidth product. According to the Texas Instruments product description, this bandwidth is available from approximately 20 microamperes of quiescent current. The combination supports general-purpose closed-loop signal amplification while maintaining low bias power for portable, sensor, and low-voltage instrumentation applications.
Does TLV2760IP have rail-to-rail input and output?
Yes, the TLV2760IP supports rail-to-rail input and output operation. The Texas Instruments family description identifies it as a rail-to-rail input/output operational amplifier. Rail-to-rail input operation extends signal range near the supply rails, while rail-to-rail output capability improves usable output swing in low-voltage circuits.
Where can I download the TLV2760IP datasheet PDF?
The official TLV2760IP datasheet is available through the Texas Instruments product page at https://www.ti.com/product/TLV2760. The manufacturer also provides the family datasheet through the TI link https://www.ti.com/cn/lit/gpn/tlv2760. Use the official PDF for the complete electrical characteristics, pin descriptions, recommended operating conditions, and application guidance.
Where can I find the TLV2760IP pinout?
The TLV2760IP pin configuration is shown in the pin-description section of the manufacturer datasheet and in the package drawing on the Texas Instruments product page. The device uses an 8-pin PDIP package. Assign PCB nets from those official diagrams rather than relying on generic operational-amplifier pinouts, because shutdown and supply functions must be mapped correctly.
What is the quiescent current of TLV2760IP?
The TLV2760IP family is specified at approximately 20 microamperes of quiescent current. Texas Instruments identifies the amplifier as a micropower device that provides 500 kHz bandwidth from this low operating current. The shutdown pin can further reduce current consumption when the amplifier is idle, making the device useful in battery-powered sensing systems.
What is the offset voltage of TLV2760IP?
The TLV2760IP is listed with a 3500 microvolt offset voltage in the family ordering information published by Texas Instruments. This distinguishes it from lower-offset members of the TLV276x family. If a precision DC application requires substantially lower input offset, review the family offset-voltage options and their input-bias trade-offs before choosing a replacement.
Is TLV2760IP suitable for battery-powered sensor interfaces?
The TLV2760IP is suitable for many battery-powered sensor interfaces because it supports operation down to 1.8 V, draws approximately 20 microamperes, and provides rail-to-rail input and output operation. These characteristics allow the amplifier to process signals from low-voltage sensors without requiring a higher supply. Check input bias current, noise, and offset requirements for the selected sensor.
TLV2760IP vs TLV2761IP - which is better for precision DC measurement?
TLV2761IP is generally the better starting point for precision DC measurement because its offset-voltage rating is lower than the TLV2760IP's 3500 microvolts. Both belong to the same 8-pin PDIP family and retain the 500 kHz bandwidth and shutdown capability. The correct choice depends on the full input-bias, voltage-noise, and offset-error requirements of the measurement.
When should I choose TLV2760IP over another TLV276x member?
Choose TLV2760IP when an 8-pin PDIP footprint, approximately 20 microamperes of quiescent current, 500 kHz bandwidth, rail-to-rail operation, and shutdown are required while the 3500 microvolt offset rating is acceptable. Select a lower-offset family member for precision DC work or a different package option when a smaller surface-mount footprint is necessary.
What can replace TLV2760IP?
The closest pin-compatible replacement is another qualified TLV276x device in the 8-pin PDIP package, but the replacement must have acceptable offset voltage, input-bias current, supply range, shutdown polarity, and bandwidth. TLV2761IP, TLV2762IP, and TLV2763IP are pin-compatible family options, not automatically equivalent functionally. Verify each device against the original circuit requirements.
What is the best Texas Instruments equivalent for TLV2760IP?
The most direct Texas Instruments family options are TLV2761IP, TLV2762IP, and TLV2763IP because each uses the same 8-pin PDIP family format. Their offset-voltage ratings differ from the TLV2760IP, so the best equivalent depends on whether low offset, low bias current, or the original 3500 microvolt class is more important. Confirm pin functions and timing in the datasheet.
Where to buy TLV2760IP online?
The TLV2760IP can be requested through the Request a Quote form on this page. The manufacturer product page and distributor listings are available for additional technical and supply-chain review. Current availability, lot allocation, and delivery timing should be confirmed during the quotation process because inventory levels can change rapidly for catalog semiconductors.
What is the price of TLV2760IP?
Use the Request a Quote form on this page for a current TLV2760IP quotation. The form supports volume, delivery, and supply requirements without embedding a static price that could become obsolete. The structured listing information on this page records the most recent reference point, while the final transaction price is established through the quotation workflow.
What is the lead time and stock status for TLV2760IP?
Request the current TLV2760IP lead time, minimum order quantity, and stock allocation through the Request a Quote form on this page. Lead time depends on order quantity, manufacturing capacity, and inventory position. The Texas Instruments product page provides ordering and quality information, while a quotation gives the current commercial commitment for the requested configuration.

工程参考数据: TLV2760IP ——对比、设计指导和合规信息。

选型指南

Choose the TLV2760IP when the design needs an 8-pin PDIP footprint, operation down to 1.8 V, rail-to-rail input and output, 500 kHz bandwidth, approximately 20 microamperes quiescent current, and an active shutdown function. Its 3500 microvolt offset-voltage rating makes it most appropriate when moderate DC error is acceptable or can be calibrated. Consider TLV2761IP, TLV2762IP, or TLV2763IP when a different offset-voltage class better matches the application, but verify their input bias, noise, and shutdown behavior. A cross-brand replacement should be selected only after confirming the same 8-pin PDIP pinout, supply range, rail-to-rail performance, output drive, stability, and shutdown logic. For designs requiring very low offset or noise, choose a lower-offset precision amplifier rather than treating any TLV276x member as automatically equivalent.

与替代料对比

参数 本产品 TLV2761IP TLV2762IP TLV2763IP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin PDIP (P) 8-pin PDIP (P) 8-pin PDIP (P) 8-pin PDIP (P)
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit
Gain-Bandwidth Product 500 kHz 500 kHz 500 kHz 500 kHz
Minimum Supply Voltage 1.8 V 1.8 V 1.8 V 1.8 V
Quiescent Current Approximately 20 microamperes Approximately 20 microamperes Approximately 20 microamperes Approximately 20 microamperes
Input and Output Operation Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Shutdown Control Yes Yes Yes Yes
Offset Voltage 3500 microvolts Different family offset class; consult the TLV276x ordering table Different family offset class; consult the TLV276x ordering table Different family offset class; consult the TLV276x ordering table

关键差异点

  • Shutdown control in a through-hole operational-amplifier package (对比 TLV2761IP)
  • Rail-to-rail operation from a low 1.8 V supply (对比 TLV2762IP)
  • Low-power operation with approximately 20 microamperes quiescent current (对比 TLV2763IP)

设计说明

Estimated: at a 3.6 V supply and 20 microamperes quiescent current, the TLV2760IP consumes approximately 72 microwatts before output-current and load effects. When shutdown is not required continuously, drive the shutdown pin from a compatible control signal to reduce supply demand. Confirm the shutdown polarity, transition timing, and leakage behavior in the manufacturer datasheet before using the control pin in a power-sequencing scheme.

Do not treat rail-to-rail input as unlimited input range. The amplifier still has absolute maximum input-voltage and supply limits, so inputs must remain within the permitted common-mode and overvoltage boundaries. Also account for the TLV2760IP's 3500 microvolt offset-voltage rating in precision DC measurements; system offset calibration may reduce static error but cannot correct input-voltage drift or noise.

Place the input, feedback, bypass, and decoupling components close to their associated amplifier pins to minimize parasitic capacitance and feedback-loop delay. Keep output and feedback routing away from shutdown traces and other high-impedance shutdown control lines. For sensitive sensor inputs, use a quiet ground reference and avoid routing the input directly beside switching nodes or digital clock lines.

The 500 kHz gain-bandwidth product limits useful closed-loop bandwidth according to the selected noise gain and feedback factor. Avoid assuming that a 500 kHz gain-bandwidth product supports a 500 kHz closed-loop signal in every topology. Check the required gain, settling tolerance, output-capacitive-load limits, and feedback-network values against the manufacturer stability and frequency-response information.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

Compliance status is not stated in the manufacturer product-page snippet or distributor results used for this listing. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation with Texas Instruments before environmental or regulatory qualification.

相关搜索

TLV2760IP TLV2760IP datasheet TLV2760IP pinout TLV2760IP datasheet pdf TLV2760IP 8-PDIP TLV2760IP equivalent TLV2760IP replacement TLV2760IP cross reference TLV2760IP vs TLV2761IP TLV2760IP application circuit Texas Instruments TLV2760IP TLV2760IP price

相关元器件 & 术语

Texas Instruments TLV2760IP TLV2761IP TLV2762IP TLV2763IP operational amplifier rail-to-rail input amplifier rail-to-rail output amplifier micropower amplifier analog integrated circuit semiconductor 500 kHz gain-bandwidth product 20 microamperes quiescent current 1.8 V minimum supply voltage 3500 microvolt offset voltage shutdown control 8-pin PDIP PDIP package family through-hole mounting battery-powered sensor interface portable instrumentation industrial control interface audio preamplifier signal conditioning
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情