TLV2760IP - 500kHz RRIO Op Amp with Shutdown | Texas Instruments
部品番号: TLV2760IP ✓ 生産中TLV2760IP 概要
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The TLV2760 belongs to the operational-amplifier hierarchy, which includes rail-to-rail amplifiers, micropower amplifiers, and general-purpose analog ICs. Rail-to-rail input operation allows the input common-mode range to extend close to the supply rails, while rail-to-rail output operation improves output swing in low-voltage systems.
The TLV2760 family provides 500 kHz bandwidth from approximately 20 microamperes of quiescent current and supports operation down to 1.8 V. The TLV2760IP is the high-offset-voltage member of the family, with a listed offset-voltage rating of 3500 microvolts. Its shutdown function allows a system designer to reduce supply current when the amplifier is not required, which is valuable in portable and battery-powered equipment.
The low operating voltage and rail-to-rail behavior make the device suitable for sensor interfaces, transducers, battery-powered instrumentation, audio signal paths, and embedded control systems. Its 500 kHz bandwidth provides enough bandwidth for general-purpose feedback and error-amplifier networks without the higher power and noise associated with much faster amplifiers.
The 8-pin PDIP package supports through-hole assembly and prototype rework, while its exposed lead spacing follows the standard 8-pin PDIP footprint. Designers should verify the shutdown-logic polarity, input bias behavior, output swing, and stability requirements against the manufacturer datasheet before using the amplifier near supply limits.
This page combines the TLV2760IP electrical characteristics, lifecycle information, package data, sourcing workflow, and practical replacement guidance. It also highlights the distinctions among TLV276x offset-voltage options so engineers can select a pin-compatible family member without overlooking offset or shutdown requirements.
ドロップイン代替品: TLV2760IP — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TLV2760IP (同一形状・フットプリント) — 相違点: Amplifier Type, Number of Circuits, Package.
TLV2761IP
✅ ドロップイン価格はお問い合わせください
データシートを見る →TLV2762IP
✅ ドロップイン価格はお問い合わせください
データシートを見る →TLV2763IP
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLV2760IP 最大定格&電気的特性
| Amplifier Type | Single operational amplifier |
| Number of Circuits | 1 circuit |
| Nominal Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 500 kHz |
| 静止電流 | 20 microamperes typical |
| Input Rail-to-Rail | Yes |
| Output Rail-to-Rail | Yes |
| Shutdown Control | Yes |
| Offset Voltage | 3500 microvolts |
| Operating Temperature Class | Industrial temperature range |
| パッケージ | 8-pin PDIP, 0.300 inch pitch |
| 実装タイプ | Through-hole |
| 出力タイプ | Rail-to-rail |
| Product Category | General-purpose amplifier |
TLV2760IP 8-pin pdip, 0.300 inch pitch ピン配置ガイド
TLV2760IP (8-pin pdip, 0.300 inch pitch パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: TLV2760IP.
詳細は データシート をご参照ください。
主な用途
TLV2760IP の用途: 6 件s: Battery-Powered Sensor Signal Conditioning, Portable Instrumentation, Low-Voltage Audio Preamplifier, Industrial Control Interface, Transducer and Bridge-Signal Amplifier, Embedded Control Signal Conditioning.
Battery-Powered Sensor Signal Conditioning
The TLV2760IP fits low-voltage sensor front ends because it operates down to 1.8 V, supports rail-to-rail input and output, and uses approximately 20 microamperes of quiescent current. It can amplify a sensor signal close to either supply rail before conversion or sampling. The shutdown function reduces current demand when sensing is intermittent. Because this TLV2760 version has a 3500 microvolt offset-voltage rating, it is most appropriate when the downstream system can tolerate that offset or when offset is corrected through calibration.
Portable Instrumentation
Portable measurement equipment benefits from the TLV2760IP's low 1.8 V minimum operating voltage and approximately 20 microamperes supply demand. Its 500 kHz gain-bandwidth product is suitable for conditioning moderate-frequency signals without requiring a high-speed amplifier. Rail-to-rail input capability preserves measurement range near the supply limits, while rail-to-rail output improves drive into a following converter or instrumentation stage. Verify the 3500 microvolt offset specification against the required measurement resolution.
Low-Voltage Audio Preamplifier
The TLV2760IP can provide input and output swing close to the rails in a low-voltage audio preamplifier, which helps preserve headroom in portable playback systems. Its 500 kHz bandwidth covers common audio-band signal conditioning, while approximately 20 microamperes of quiescent current limits continuous power use. The shutdown control can disable the amplifier between active intervals. For high-fidelity designs, compare the device's offset, noise, and output-drive characteristics with the selected audio requirements.
Industrial Control Interface
The TLV2760IP is applicable to low-voltage industrial interface circuits that require rail-to-rail input operation, such as conditioning a controller signal or driving a slow analog input. Its approximately 20 microamperes quiescent current supports distributed low-power sensing, and the shutdown function permits controlled operating states. The industrial temperature-range designation supports industrial environments, but designers should verify absolute maximum ratings, input bias current, and offset stability for the specific control loop.
Transducer and Bridge-Signal Amplifier
For low-level transducer signals, the TLV2760IP's rail-to-rail input and output behavior can be useful when the transducer operates close to the available supply range. The 500 kHz gain-bandwidth product supports practical audio-band and instrumentation bandwidth, and the shutdown function allows the amplifier to remain off outside measurement intervals. Check the TLV2760IP's 3500 microvolt offset rating, input bias current, and noise against the transducer's sensitivity before choosing the final gain configuration.
Embedded Control Signal Conditioning
The TLV2760IP can condition sensor, feedback, or reference signals around a low-voltage embedded controller. Its 500 kHz bandwidth supports general-purpose amplifier networks, and operation down to 1.8 V allows use with low-energy supply rails. Rail-to-rail inputs reduce common-mode headroom concerns, while the shutdown input permits power-state management. Ensure the controller's ADC input range, amplifier stability with the selected feedback network, and settling requirements are satisfied before deployment.
エンジニアリング参考データ: TLV2760IP — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV2761IP | TLV2762IP | TLV2763IP |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-pin PDIP (P) | 8-pin PDIP (P) | 8-pin PDIP (P) | 8-pin PDIP (P) |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 500 kHz | 500 kHz | 500 kHz | 500 kHz |
| Minimum Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Quiescent Current | Approximately 20 microamperes | Approximately 20 microamperes | Approximately 20 microamperes | Approximately 20 microamperes |
| Input and Output Operation | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shutdown Control | Yes | Yes | Yes | Yes |
| Offset Voltage | 3500 microvolts | Different family offset class; consult the TLV276x ordering table | Different family offset class; consult the TLV276x ordering table | Different family offset class; consult the TLV276x ordering table |
主な差別化要因
- Shutdown control in a through-hole operational-amplifier package (vs TLV2761IP)
- Rail-to-rail operation from a low 1.8 V supply (vs TLV2762IP)
- Low-power operation with approximately 20 microamperes quiescent current (vs TLV2763IP)
設計ノート
Estimated: at a 3.6 V supply and 20 microamperes quiescent current, the TLV2760IP consumes approximately 72 microwatts before output-current and load effects. When shutdown is not required continuously, drive the shutdown pin from a compatible control signal to reduce supply demand. Confirm the shutdown polarity, transition timing, and leakage behavior in the manufacturer datasheet before using the control pin in a power-sequencing scheme.
Do not treat rail-to-rail input as unlimited input range. The amplifier still has absolute maximum input-voltage and supply limits, so inputs must remain within the permitted common-mode and overvoltage boundaries. Also account for the TLV2760IP's 3500 microvolt offset-voltage rating in precision DC measurements; system offset calibration may reduce static error but cannot correct input-voltage drift or noise.
Place the input, feedback, bypass, and decoupling components close to their associated amplifier pins to minimize parasitic capacitance and feedback-loop delay. Keep output and feedback routing away from shutdown traces and other high-impedance shutdown control lines. For sensitive sensor inputs, use a quiet ground reference and avoid routing the input directly beside switching nodes or digital clock lines.
The 500 kHz gain-bandwidth product limits useful closed-loop bandwidth according to the selected noise gain and feedback factor. Avoid assuming that a 500 kHz gain-bandwidth product supports a 500 kHz closed-loop signal in every topology. Check the required gain, settling tolerance, output-capacitive-load limits, and feedback-network values against the manufacturer stability and frequency-response information.
コンプライアンス情報
Compliance status is not stated in the manufacturer product-page snippet or distributor results used for this listing. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals documentation with Texas Instruments before environmental or regulatory qualification.