W79E9781AKG - 8-bit MCU 64KB Flash | Nuvoton | Industrial
料号： W79E9781AKG ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $3.75 | $3.75 |
| 10 | $3.38 | $33.80 |
| 100 | $2.99 | $299.00 |
| 500 | $2.69 | $1,345.00 |
| 1,000 | $2.4 | $2,400.00 |
W79E9781AKG 概述
An 8-bit microcontroller (MCU) is a microprocessor-on-a-chip that integrates a CPU, program memory, data RAM, and peripherals into a single IC. The 8-bit architecture is optimized for cost-sensitive, low-power, deterministic control tasks; in the system hierarchy an MCU sits between discrete logic ICs and 32-bit microprocessors, providing firmware-driven I/O handling, sensor interfacing, and protocol conversion. Nuvoton's W79 family extends the legacy 8051 instruction set with Turbo-MCU enhancements, doubling the standard clock-per-instruction cycle for higher throughput at the same crystal frequency.
Key features include 64 KB of in-system programmable (ISP) Flash allowing field firmware updates via UART, an operating voltage range of 2.4V to 5.5V that supports both 3.3V and 5V rails, and an industrial-grade operating temperature of -40C to +85C. The on-chip 10-bit ADC provides up to 8 analog input channels, while the four 16-bit timer/counters support PWM generation, capture, and event counting. A dedicated hardware watchdog and brown-out reset circuit protect against code lockup and unstable supplies.
The W79E9781AKG uses the standard 8051 instruction set with Nuvoton Turbo-MCU extensions, allowing one machine cycle per clock rather than the original 12, while preserving binary compatibility with legacy 8051 firmware. The device's ISP mechanism boots from a ROM-resident bootloader that re-programs the Flash via the UART pins, eliminating external programming hardware during prototyping and field service.
Typical applications include industrial control panels, home appliance main boards, motor control BLDC drivers, smart meter data concentrators, and point-of-sale terminals. The integrated ADC, timers, and UART let designers replace multiple discrete components with a single chip, shrinking BOM cost and PCB area.
When designing with this device, plan ISP access by routing the UART pins to a header or optocoupler-isolated connector. Use the brown-out detector level matched to the lowest reliable rail voltage (typically 2.7V for 3.3V systems) to prevent Flash corruption during power-down events.
This page consolidates distributor pricing, package-level drop-in alternatives, and engineering design notes that go beyond the manufacturer datasheet, supporting faster component selection and risk-aware substitution decisions.
直接替换替代料： W79E9781AKG ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
快速对比工具——选择替代料号进行并排对比：
W79E9783AKG
✅ 直接替换📋 参考替代料（不在目录中）
W79E9791AKG
✅ 直接替换📋 参考替代料（不在目录中）
W79E6325AKG
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料（不在目录中）
W79E9781AKG 最大额定值与电气特性
| Core Architecture | 8-bit 8051 (Turbo-MCU) |
| Instruction Set | 8051-compatible with Nuvoton extensions |
| Program Memory (Flash) | 64 KB |
| SRAM | 1.25 KB |
| Operating Voltage Range | 2.4 V to 5.5 V |
| 最大时钟频率 | 40 MHz |
| ADC | 10-bit, up to 8 channels |
| Timers | 4 x 16-bit |
| Watchdog Timer | Yes |
| Brown-Out Detector | Yes |
| UART | 1 x hardware full-duplex |
| I2C / SPI | I2C master + SPI master |
| 工作温度 | -40 C to +85 C |
| 封装 | LQFP-128 |
| 安装类型 | Surface Mount |
| RoHS 状态 | Compliant |
| In-System Programming | Yes (UART bootloader) |
W79E9781AKG lqfp-128 引脚配置指南
W79E9781AKG（lqfp-128 封装）的引脚配置。 该数字 IC 包含 GPIO、通信接口（UART、SPI、I2C）和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据： W79E9781AKG.
请参阅 数据手册 以查看完整引脚配置。
典型应用
W79E9781AKG 适用于 6 应用s: Industrial Control Panels, Home Appliance Main Boards, BLDC Motor Drivers, Smart Meter Data Concentrators, Point-of-Sale Terminals, Sensor Hubs and IoT Edge Nodes.
Industrial Control Panels
The W79E9781AKG fits industrial control panels because its 64 KB ISP Flash and 1.25 KB SRAM handle menu-driven HMI logic, while the 10-bit ADC reads analog sensor inputs such as temperature and pressure. The wide 2.4-5.5V supply tolerates noisy 24V-derived industrial rails after regulation, and the -40C to +85C operating temperature covers factory floor environments. The hardware watchdog and brown-out detector protect against code lockup and supply sag, critical for unattended control cabinets.
推荐
Home Appliance Main Boards
The W79E9781AKG suits home appliance main boards - washing machines, microwave ovens, and air conditioners - where its 8051-compatible core simplifies firmware reuse across product lines. The four 16-bit timers drive PWM outputs for motor and heater control, while the hardware UART links to display modules or Wi-Fi companion modules. ISP via UART allows field firmware updates without disassembly, a strong advantage for appliance OEMs managing long product lifecycles.
推荐
BLDC Motor Drivers
The W79E9781AKG supports low-to-mid complexity BLDC motor drivers by using its 16-bit timers to generate 3-phase complementary PWM with dead-time insertion, and its 10-bit ADC to sample back-EMF for sensorless commutation. The 40 MHz Turbo-MCU core provides enough headroom for trapezoidal or simple sinusoidal control loops. The integrated brown-out detector prevents erratic motor behavior during supply transients common in motor inrush events.
推荐
Smart Meter Data Concentrators
The W79E9781AKG can serve as the local data concentrator in smart-meter networks, gathering pulses from electricity/water/gas meters and forwarding aggregated data via the hardware UART to a cellular or PLC modem. The 64 KB Flash accommodates DLMS/COSEM or proprietary metering stacks, while the watchdog timer guards against meter hangs. The industrial -40C to +85C rating handles outdoor meter cabinet conditions.
推荐
Point-of-Sale Terminals
The W79E9781AKG handles the keyboard, display, and printer interface in low-cost point-of-sale terminals where cost dominates over raw processing speed. Its UART links to a mag-stripe or smartcard reader, its I2C/SPI master drives an LCD or thermal printer controller, and ISP via UART allows secure firmware updates at deployment sites. The 5V-tolerant I/O simplifies interfacing with legacy POS peripherals.
推荐
Sensor Hubs and IoT Edge Nodes
The W79E9781AKG can act as an edge sensor hub aggregating analog and digital sensors and forwarding pre-processed data via UART to a higher-level gateway. The 10-bit ADC samples multiple sensor channels, the timers schedule periodic wake-and-measure cycles, and the brown-out detector preserves node state across brown-out events. ISP enables OTA-style field updates when paired with a companion wireless module.
推荐
推荐产品汇总
工程参考数据： W79E9781AKG ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | W79E9783AKG | W79E9791AKG | W79E6325AKG |
|---|---|---|---|---|
| Brand | Nuvoton | Nuvoton | Nuvoton | Nuvoton |
| Package | LQFP-128 | LQFP-128 - same | LQFP-128 - same | LQFP-128 - same |
| Core | 8-bit 8051 Turbo | 8-bit 8051 Turbo | 8-bit 8051 Turbo | 8-bit 8051 |
关键差异点
- Wide 2.4V to 5.5V supply range （对比 W79E6325AKG)
- Integrated ISP UART bootloader （对比 Generic 8051 MCUs)
- 64 KB Flash on a 40 MHz Turbo-MCU core （对比 W78E052D)
设计说明
The W79E9781AKG operates from 2.4V to 5.5V; place a 10uF bulk capacitor plus a 0.1uF ceramic decoupling cap close to the VDD pins to suppress switching transients. Use the on-chip brown-out detector set to the minimum reliable rail voltage (e.g., 2.7V for a 3.3V system) to prevent Flash corruption during power-down events.
Route the ISP UART pins (TX, RX) to a header or optocoupler-isolated connector so that firmware can be updated in-circuit. Keep the UART traces short and away from switching power or motor driver traces to avoid bootloader-mode glitches during field programming.
Estimated: total Flash endurance is typically rated at 100K erase/write cycles - design firmware update flows to minimize unnecessary writes and avoid using Flash as a high-write-rate log. The watchdog timer must be refreshed periodically in firmware; failure to refresh will reset the device.
合规信息
RoHS compliant per Nuvoton product page. Standard variant is not AEC-Q100 qualified; for automotive choose the Q1 suffix variant. Halogen-free status not explicitly stated in provided data.
