WM8711CLGEFL/R - 24-Bit Stereo Audio DAC | Cirrus Logic
料号: WM8711CLGEFL/R ✗ 停产WM8711CLGEFL/R 概述
An audio DAC is a digital-to-analog converter, a category of data-conversion IC that transforms digital audio samples into continuous analog voltage signals. In the broader signal-chain hierarchy, it sits between a digital audio source—such as a host controller, USB interface, or digital audio processor—and an analog headphone or line-output amplifier. A stereo DAC supports two independent audio channels, while its DSP functions can perform signal processing before the analog output stage.
The WM8711CLGEFL/R combines a 24-bit conversion format with operation up to 96 kHz. Its I2S interface provides a conventional digital audio connection to a source device, while the integrated DSP adds configurable processing capability. The dual-channel architecture supports stereo playback paths, and the listed headphone and line-in functions allow the device to participate in complete audio signal chains rather than serving only as a basic conversion stage.
The component uses CMOS technology and is packaged in a compact 28-terminal PQCC28-style surface-mount package measuring 5 x 5 mm with a stated 0.85 mm pitch. Its low-voltage 1.42 V to 3.6 V operating range is suitable for portable and embedded audio systems in which supply efficiency and board area are important. The reel suffix identifies the tape-and-reel shipping configuration represented by the WM8711CLGEFL/R ordering code.
Typical uses include digital headphone playback, line-level stereo audio outputs, compact consumer audio equipment, portable media systems, and embedded audio subsystems. In these applications, the I2S interface can receive digital samples from an audio controller, the DSP can perform configured signal processing, and the converter can generate stereo analog signals for downstream amplification. The exact digital format, master-clock requirements, filter configuration, and output topology should be confirmed from the manufacturer datasheet.
Designers should treat the 1.42 V minimum and 3.6 V maximum supply limits as firm operating boundaries. Decoupling, analog-output routing, clock generation, and exposed-pad thermal management must follow the recommended layouts in the manufacturer datasheet. This part has a documented end-of-life notice, so new designs should confirm lifecycle availability and obtain an approved sourcing plan before committing the component to a production BOM.
This page consolidates the confirmed converter architecture, package information, supply limits, lifecycle notice, sourcing guidance, and engineering considerations for engineers evaluating the WM8711CLGEFL/R. It also distinguishes documented device functions from parameters that require direct verification in the manufacturer datasheet, helping teams assess fit before layout work begins.
直接替换替代料: WM8711CLGEFL/R ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料WM8711CLGEFL/R 最大额定值与电气特性
| Product Type | Stereo audio digital-to-analog converter |
| Converter Resolution | 24 bit |
| Maximum Sampling Rate | 96 kHz |
| Number of Channels | 2 channels |
| Digital Audio Interface | I2S |
| Signal Processing | DSP |
| Supply Voltage Range | 1.42 V to 3.6 V |
| Package Type | 28-QFN |
| Package Dimensions | 5 mm x 5 mm |
| Package Pitch | 0.85 mm |
| Package Form | PQCC28 |
| Termination Count | 28 terminals |
| 安装类型 | Surface mount |
| Manufacturing Technology | CMOS |
| Integrated Functions | Stereo DAC, headphone output, and line input |
| 输出类型 | Standard |
WM8711CLGEFL/R pqcc28 引脚配置指南
WM8711CLGEFL/R(pqcc28 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: WM8711CLGEFL/R.
请参阅 数据手册 以查看完整引脚配置。
典型应用
WM8711CLGEFL/R 适用于 6 应用s: Digital Headphone Playback, Stereo Line-Level Audio Output, Portable Media Player, Compact Consumer Audio System, Embedded Audio Interface, Digital Audio Source Module.
Digital Headphone Playback
The WM8711CLGEFL/R fits digital headphone playback systems that require a dedicated 24-bit stereo conversion stage operating up to 96 kHz. Its I2S interface accepts digital audio from a host or audio processor, while the integrated headphone and DSP functions provide a more complete signal path than a basic fixed-function converter. In a portable design, the 1.42 V to 3.6 V supply range can support a low-voltage audio architecture, and the compact 5 x 5 mm QFN outline helps conserve board area. The implementation must follow the manufacturer recommendations for analog-output routing, filtering, decoupling, exposed-pad grounding, and clock configuration. Engineers should also confirm that the end-of-life status does not conflict with the product’s production schedule.
Stereo Line-Level Audio Output
The WM8711CLGEFL/R is suitable for generating two analog audio channels from an I2S digital source in line-level playback equipment. Its 24-bit format preserves high-resolution source data, and operation up to 96 kHz accommodates CD-rate and higher-rate digital audio streams. The converter can sit near the line-output stage, reducing the distance over which sensitive analog signals travel before amplification. DSP support permits configurable processing within the conversion stage, while the low-voltage 1.42 V to 3.6 V operating range accommodates compact consumer systems. Layout should prioritize short analog traces, appropriate return paths, stable supply decoupling, and manufacturer-recommended clock routing. Because this MPN is end-of-life, a production design should document the required quantities and obtain a controlled supply commitment.
Portable Media Player
The WM8711CLGEFL/R can serve as the digital-to-analog section of a portable media player when low supply voltage, small footprint, and high-resolution stereo playback are priorities. A digital audio controller can stream 24-bit samples through I2S at rates up to 96 kHz, and the converter can support headphone and line-related audio functions within the same compact design. The 5 x 5 mm QFN package leaves board area for storage, connectivity, and power-management circuitry. Designers should check headphone-drive requirements, analog output levels, clock stability, and passive-component selection against the manufacturer datasheet. Power and thermal planning should account for the complete audio subsystem rather than the converter alone, while careful ground partitioning helps prevent digital and analog crosstalk.
Compact Consumer Audio System
The WM8711CLGEFL/R fits compact consumer audio systems that need two-channel playback from a digital source. Its 24-bit DAC architecture and 96 kHz maximum rate support modern digital-audio formats, while the integrated DSP allows configurable signal processing ahead of the analog output stage. The two-channel implementation simplifies stereo routing compared with a design requiring separate converter devices. In a space-constrained enclosure, the 28-QFN 5 x 5 mm footprint helps maintain a compact board layout. Exact line-output, headphone, and filtering settings must be selected with the manufacturer guidance, and the exposed pad should be connected according to the recommended thermal and electrical layout. For ongoing production, lifecycle risk should be addressed through approved sourcing rather than an assumption of general distributor availability.
Embedded Audio Interface
The WM8711CLGEFL/R can provide a stereo analog playback output for embedded systems whose digital controller supports I2S. Its 24-bit resolution and 96 kHz capability make it appropriate for high-quality media playback, notification tones, and mixed digital audio workflows. The integrated DSP provides a configurable processing stage, while line-in and headphone functions support broader signal routing within a compact subsystem. The low 1.42 V to 3.6 V supply range may align with the logic rails used by the surrounding controller, although each rail and sequencing requirement must be confirmed. Board implementation should isolate clock and digital return paths from the analog outputs, place bypass capacitance as directed, and follow the exposed-pad connection pattern. A production schedule should also account for the documented end-of-life status.
Digital Audio Source Module
The WM8711CLGEFL/R is appropriate for a dedicated digital-audio source module that translates I2S data into stereo analog signals. The 24-bit conversion format supports detailed digital source information, and the 96 kHz rate ceiling covers high-resolution playback use cases. Integrating conversion, DSP, headphone-related circuitry, and line-input support can shorten the analog path and reduce the number of separate signal-chain components. The device’s 5 x 5 mm QFN footprint supports module miniaturization, but thermal and electrical performance depend on correct exposed-pad soldering and copper layout. Engineers should verify supported master-clock ratios, interface polarity, sample-rate restrictions, and analog filter settings in the manufacturer datasheet. For long-lived products, a supported codec may offer better lifecycle assurance.
工程参考数据: WM8711CLGEFL/R ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Package | 28-QFN (5 x 5 mm) |
| Brand | Cirrus Logic |
| Converter Resolution | 24 bit |
| Maximum Sampling Rate | 96 kHz |
| Number of Channels | 2 channels |
| Digital Audio Interface | I2S |
| Supply Voltage Range | 1.42 V to 3.6 V |
| Signal Processing | DSP |
| Integrated Audio Functions | Headphone and line input |
| Mounting Type | Surface mount |
关键差异点
- Dedicated stereo DAC integration (对比 Generic active audio codec)
- High-resolution sampling capability (对比 Lower-resolution stereo DAC)
- Compact integrated audio functions (对比 Discrete audio conversion stage)
设计说明
Place the WM8711CLGEFL/R close to the source and analog-output circuitry, keep the I2S and clock routes away from sensitive analog outputs, and follow the manufacturer reference layout. The 28-QFN exposed pad is part of the thermal and electrical design and should use the recommended via pattern, solder process, and ground-plane connection. Validate the final stack-up and assembly process before releasing the PCB.
Operate the device only within the documented 1.42 V to 3.6 V supply range. Place the recommended bypass capacitors close to the supply and ground pins, verify startup behavior for the selected supply sequence, and avoid routing switching-current paths through the audio ground area. Because the converter operates from a low-voltage rail, ripple and ground movement can affect analog performance even when the digital interface operates correctly.
Confirm the supported master-clock ratios, I2S format, bit alignment, and sample-rate constraints in the manufacturer datasheet before fixing the host interface. Use continuous reference planes and minimize stubs on digital lines, and provide a clean return path beneath clock and data routes. Analog output filtering and output loading must also follow the documented implementation so that measured bandwidth and distortion match the design intent.
Do not confuse a similar order code with a verified drop-in replacement, and do not infer pin compatibility from the shared 28-QFN outline alone. The WM8711CLGEFL/R is identified in an end-of-life notice; teams should freeze the electrical and mechanical design early, document exact reel requirements, and obtain an approved supply plan. Any migration candidate must be checked pin by pin and against clock, DSP, headphone, and analog-output requirements.
合规信息
The verified product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not applicable to this consumer audio converter.