XC7A100T-1FGG676C - 101,440-Cell Artix-7 FPGA | AMD
料号: XC7A100T-1FGG676C ✓ 量产中XC7A100T-1FGG676C 概述
An Artix-7 FPGA belongs to the FPGA and CPLD hierarchy, combining programmable logic fabric, configurable logic blocks, block RAM, DSP slices, programmable I/O, and dedicated configuration resources on one semiconductor. This integration allows engineers to implement control logic, interfaces, packet processing, image pipelines, and fixed-function digital systems without combining separate programmable logic and supporting devices.
The XC7A100T provides 7,925 logic array blocks, 240 DSP slices, and nearly 5 Mb of block RAM. Its 300 user I/O pins support high external connectivity for parallel buses, high-speed interfaces, and mixed signal connectivity. The 28 nm Artix-7 architecture is optimized for low power and high performance per watt, while the -1 speed grade provides a defined performance target for commercial-temperature designs.
Three package variants use the FGG676 designation, but their ordering codes can identify different speed grades, temperature grades, or lifecycle classifications. The target suffix C denotes the commercial-temperature option, while the leading -1 identifies the speed grade. Pin compatibility must be checked against the exact package pinout file, and configuration-bitstream compatibility must be confirmed before treating another ordering code as a drop-in replacement.
Typical uses include industrial image acquisition, video processing, robotics, communications infrastructure, test equipment, and embedded control systems with extensive parallel I/O. The FPGA can support simultaneous control, buffering, filtering, and protocol conversion while centralizing programmable logic in one package. External memory and high-speed transceiver or interface components may still be required when the design exceeds the device's internal resources.
PCB design should allocate a continuous ground plane, route dedicated configuration pins according to the AMD package guidance, and use the package-specific ball map when defining escape routing. Because the BGA-676 footprint is dense and ball pitches are fine, component placement, solder-mask design, via-in-pad treatment, and assembly capability should be reviewed early in the board architecture.
This product record combines the exact device identity, architecture-level resources, package details, configuration considerations, drop-in alternatives, and practical PCB guidance needed to evaluate the XC7A100T-1FGG676C before schematic capture and prototype production.
直接替换替代料: XC7A100T-1FGG676C ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: XC7A100T-1FGG676C (相同外形与封装尺寸) ——差异在于 Core Supply Voltage, Package, Temperature Grade.
XC7A100T-1FGG676I
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →XC7A100T-2FGG676C
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
XC7A100T-1FGG676E
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
XC7A100T-2FGG676E
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
XC7A100T-1FGG676C 最大额定值与电气特性
| FPGA Family | Artix-7 |
| Logic Cells | 101,440 cells |
| Logic Array Blocks | 7,925 LABs |
| Block RAM | 4,976,640 bits |
| DSP Slices | 240 slices |
| User I/O Pins | 300 pins |
| 封装 | 676-ball FGG676 BGA, 27 mm x 27 mm |
| Process Technology | 28 nm |
| Speed Grade | -1 |
| Temperature Grade | Commercial |
| 工作结温 | 0 °C to 85 °C |
| Core Supply Voltage | 0.95 V to 1.05 V |
| Configuration Memory | 4,976,640 bits |
| I/O Type | User-programmable |
| 安装类型 | Surface-mount BGA |
| Package Ball Count | 676 balls |
XC7A100T-1FGG676C 676 balls 引脚配置指南
XC7A100T-1FGG676C(676 balls 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: XC7A100T-1FGG676C.
请参阅 数据手册 以查看完整引脚配置。
典型应用
XC7A100T-1FGG676C 适用于 6 应用s: Industrial Machine Vision, Video Processing, Industrial Communications Gateway, Robotics Control Platform, Test and Measurement Equipment, Aerospace Ground-Support Equipment.
Industrial Machine Vision
The XC7A100T-1FGG676C fits industrial machine-vision systems that combine parallel camera capture, preprocessing, buffering, and control in one programmable device. Its 101,440 logic cells and 240 DSP slices provide room for pixel pipelines and fixed-point filtering, while 300 user I/O pins support camera data, encoders, triggers, and machine-control signals. The 4,976,640 bits of block RAM can hold line buffers and working images when external memory is unnecessary. Designers should use the -1 timing limits during pipeline analysis, validate worst-case I/O timing, and include the commercial 0 °C to 85 °C junction range in the enclosure thermal assessment.
推荐
Video Processing
The XC7A100T-1FGG676C can implement multi-stage video processing where parallel arithmetic, line buffering, and control logic must operate concurrently. The 240 DSP slices support multiply-accumulate operations, the 7,925 LABs accommodate control and datapath logic, and the large block-RAM capacity supports frame or line storage. Its 300 user I/O positions are useful for parallel pixel interfaces, although high-resolution serial video normally requires external PHY components. System timing should be evaluated for the -1 speed grade, and the power estimate should include switching activity at video clock rates because utilization-dependent dynamic power can materially affect cooling requirements.
推荐
Industrial Communications Gateway
The XC7A100T-1FGG676C is suitable for a communications gateway that must terminate several parallel protocols while buffering packets and maintaining deterministic control. Programmable logic can implement protocol conversion, framing, filtering, and supervisory functions, while the 240 DSP slices and 4,976,640 block-RAM bits support data movement and signal-processing tasks. The 300 user I/O pins allow direct connection to multiple bus-oriented transceivers without an external CPLD. Designers should calculate timing margins for the selected -1 speed grade, use the AMD device map for every ball assignment, and isolate high-speed transceiver routes from sensitive configuration and reference circuitry.
推荐
Robotics Control Platform
The XC7A100T-1FGG676C can centralize robotic motion control, sensor fusion, safety interlocks, and communication tasks within a single Artix-7 device. Its 101,440 logic cells allow deterministic control logic to coexist with complex state machines, while the DSP slices can support filtering or fixed-point transforms on motion and environmental data. With 300 user I/O pins, the device can connect encoders, resolvers, sensors, actuators, and industrial networks through suitable external interfaces. Timing closure should include worst-case routing delays, and firmware or configuration management should include checksum verification, recovery after power loss, and controlled reconfiguration for field-updatable systems.
推荐
Test and Measurement Equipment
The XC7A100T-1FGG676C is a useful controller for test and measurement equipment requiring parallel acquisition, pattern generation, timing control, and analysis in one device. Its 7,925 LABs can implement multiple channels of acquisition control, while 240 DSP slices and abundant block RAM support filtering, correlation, or waveform analysis. The 300 user I/O pins provide connectivity to parallel converters, memory, and trigger circuitry, subject to the exact bank voltage and pin-function constraints in the package map. For laboratory instruments, validate channel-to-channel skew, use the FGG676 power and ground-ball assignments, and estimate both static and activity-dependent power for the final instrument operating profile.
推荐
Aerospace Ground-Support Equipment
The XC7A100T-1FGG676C can be evaluated for aerospace ground-support equipment when the required environmental class permits commercial-temperature operation. Its large programmable fabric supports redundant logic, telemetry processing, simulation, and interface conversion, while 300 I/O positions simplify integration with legacy parallel equipment. Because the ordering code is not an automotive-qualified variant, the complete system must address the aerospace program's environmental, reliability, traceability, and configuration-control requirements independently. Engineers should use the exact AMD package files for layout, compare -1 timing data against the system clock plan, and build configuration redundancy rather than relying on a single boot path.
推荐
推荐产品汇总
工程参考数据: XC7A100T-1FGG676C ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | XC7A100T-2FGG676I | XC7A100T-1FGG676I | XC7A100T-2FGG676C | XC7A100T-1FGG676E | XC7A100T-2FGG676E |
|---|---|---|---|---|---|---|
| Brand | AMD | AMD | AMD | AMD | AMD | AMD |
| Package | 676-ball FGG676 BGA | 676-ball FGG676 BGA | 676-ball FGG676 BGA | 676-ball FGG676 BGA | 676-ball FGG676 BGA | 676-ball FGG676 BGA |
| FPGA Family | Artix-7 | Artix-7 | Artix-7 | Artix-7 | Artix-7 | Artix-7 |
| Logic Cells | 101,440 cells | 101,440 cells | 101,440 cells | 101,440 cells | 101,440 cells | 101,440 cells |
| Block RAM | 4,976,640 bits | 4,976,640 bits | 4,976,640 bits | 4,976,640 bits | 4,976,640 bits | 4,976,640 bits |
| DSP Slices | 240 slices | 240 slices | 240 slices | 240 slices | 240 slices | 240 slices |
| User I/O Pins | 300 pins | 300 pins | 300 pins | 300 pins | 300 pins | 300 pins |
| Speed Grade | -1 | -2 | -1 | -2 | -1 | -2 |
| Process Technology | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm | 28 nm |
关键差异点
- Commercial-temperature -1 device with substantial Artix-7 resources (对比 XC7A100T-2FGG676I)
- Lower speed grade supports cost-sensitive designs meeting -1 timing limits (对比 XC7A100T-2FGG676C)
- Exact commercial-temperature ordering option (对比 XC7A100T-1FGG676I)
设计说明
Use the AMD FGG676 package pinout file as the controlling source for every ball assignment and PCB footprint. The 676-ball BGA includes signal, power, ground, configuration, and dedicated-function balls, so the 300 user I/O count does not describe the physical pad count. Compare the land pattern, solder-mask opening, paste stencil, and assembly process against the selected package drawing before releasing fabrication outputs.
Build the power estimate around actual clock, I/O activity, LUT occupancy, DSP use, block-RAM use, and the selected core voltage rather than a fixed wattage. Decouple each required supply rail according to the AMD power-guidance document, place bulk and local decoupling at the associated BGA power balls, and keep switching-current return paths short. Review the estimate again after implementation because utilization changes can materially change dynamic power.
Plan configuration pins, dedicated pins, supply balls, and ground balls before placing general-purpose user I/O. Use the package-specific escape strategy for a 27 mm by 27 mm FGG676 footprint, preserve uninterrupted ground reference planes, and avoid routing sensitive signals across split planes. PCB assembly capability should be checked for the ball pitch, solder-mask definition, via strategy, and required X-ray inspection coverage.
Do not treat every FGG676 ordering code as automatically interchangeable. The speed grade, temperature class, lifecycle status, and exact package documentation must match the design requirements. Also do not infer the pinout from the number of user I/O pins. Download the exact device map, verify configuration pin requirements, and confirm that the replacement device identifier is supported by the selected configuration memory and tool flow.
合规信息
Material-compliance status is not stated for the exact ordering code. The commercial-temperature device is not an explicitly automotive-qualified ordering option.