Z86C9325FSC - 25MHz ROMless 8-Bit MCU | Zilog | 44-QFP
料号: Z86C9325FSC ✗ 停产Z86C9325FSC 概述
A ROMless microcontroller is an 8-bit embedded processor whose program storage is external rather than embedded in the device. The Z86C9325FSC therefore functions as a complete controller core, using external memory for firmware and data. Within the embedded-device hierarchy, it belongs to the microprocessor and microcontroller class, combines an 8-bit CPU with dedicated arithmetic and timing peripherals, and supports designs requiring deterministic control without a large embedded ROM. External program and data memory also make this architecture useful where firmware updates or field-reprogrammable logic are needed.
The principal feature set includes the 25 MHz maximum clock, ROMless operation, the hardware multiplier, the divider, three 16-bit timer/counter channels, a capture register, and fast decrement mode. Additional interface signals identified for the Z86C9325 family include SCLK, IACK, SYNC, and WAIT. These characteristics make the part suitable for industrial controllers, motor-control systems, instrumentation, communications equipment, and legacy Z8-based embedded products where a compact 8-bit control engine is preferred.
The Z86C93 architecture separates general control from frequently used arithmetic operations. A hardwired 16-bit by 16-bit multiplier accelerates multiplication without a software loop, while the 32-bit by 16-bit divider supports higher-width division tasks. The three 16-bit counters provide timing resources for periodic generation, event counting, pulse measurement, and motor or actuator sequencing. The capture register and fast decrement function improve handling of external timing events and countdown-style control sequences.
The 44-QFP package provides 44 external connections in a square surface-mount form factor. Because this is a ROMless design, the board must provide suitable external program and data memory, address and data buses, and the required control signals. Decoupling and signal-integrity practices become particularly important because processor activity can produce fast bus transitions. The 5.00 V maximum supply rating should be treated as the principal electrical boundary during schematic design and component selection.
Typical implementation involves placing the controller beside external memory and interface circuitry, then using its counters and arithmetic accelerators for control-loop or communication tasks. Firmware timing must allow for memory access and peripheral synchronization. The 25 MHz clock rate provides more computation than typical low-end 8-bit controllers, while the multiplier and divider can reduce instruction overhead in control algorithms. Firmware and memory timing should nevertheless be verified together because external memory access can affect real-time behavior.
This page consolidates the device identity, package information, family-level arithmetic capabilities, sourcing guidance, and engineering trade-offs around the Z86C9325FSC. It also distinguishes a confirmed same-package replacement from functional alternatives that would require a board redesign, helping engineers identify a valid hardware substitution without confusing general MCU similarity with true pin-to-pin compatibility.
直接替换替代料: Z86C9325FSC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: Z86C9325FSC (相同外形与封装尺寸) ——差异在于 Architecture, Package, Program Memory.
Z86C9325FSG
✅ 直接替换📋 参考替代料(不在目录中)
Z86C9325FSC 最大额定值与电气特性
| Device Type | 8-bit ROMless microcontroller |
| Architecture | Z8 |
| 最大时钟频率 | 25 MHz |
| 电源电压 | 5.00 V maximum |
| Multiplier | Hardwired 16-bit x 16-bit |
| Divider | Hardwired 32-bit / 16-bit |
| Counter Timers | 3 x 16-bit |
| Program Memory | External ROMless architecture |
| 封装 | 44-pin QFP |
| Terminal Count | 44 terminals |
| 安装方式 | Surface mount |
| Terminal Form | Gull wing |
| Package Shape | Square |
| Temperature Grade | Commercial |
| Additional Interface Signals | SCLK, IACK, SYNC, WAIT |
| Capture Register | Present |
| Fast Decrement Mode | Present |
| Process Technology | CMOS |
Z86C9325FSC square 引脚配置指南
Z86C9325FSC(square 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: Z86C9325FSC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
Z86C9325FSC 适用于 6 应用s: Legacy Industrial Control, Motor Control and Sequencing, Instrumentation and Signal Conditioning, Communications Controller, Embedded Data Acquisition, Appliance and Service Electronics.
Legacy Industrial Control
The Z86C9325FSC is appropriate for maintaining an established Z8-based industrial controller because its 8-bit CPU, 25 MHz clock, and ROMless architecture preserve the existing instruction set and external-memory design. The hardwired 16-bit by 16-bit multiplier and 32-bit by 16-bit divider can reduce software overhead in scaling, compensation, and interpolation routines, while three 16-bit timers provide deterministic event-counting resources. Its 5.00 V maximum supply requirement and 44-QFP footprint must match the original board. For industrial service, validate temperature grade, controller lifecycle, and any required diagnostic or programming accessories before deployment.
推荐
Motor Control and Sequencing
The Z86C9325FSC suits legacy motor-control and sequencing platforms built around the Z86C93 architecture. Its three 16-bit counter timers support periodic timing, event counting, and actuator sequencing, while the capture register assists with external timing measurements. The hardware multiplier accelerates multiplication in position, speed, and scaling calculations, and the 32-bit by 16-bit divider supports higher-width arithmetic. Because the MCU is ROMless, firmware remains in external memory and must be coordinated with bus timing. Confirm the counter assignments, external driver interfaces, protection scheme, and worst-case timing before adapting it to a new motor platform.
推荐
Instrumentation and Signal Conditioning
The Z86C9325FSC can support legacy instrumentation front ends when the host controller must combine external-memory firmware with dedicated arithmetic. Its 25 MHz 8-bit processor provides useful throughput for sensor conditioning, calibration, and display-control tasks, while the hardwired multiplier and divider improve computational efficiency without replacing the CPU. The three timers can organize sampling, conversion, and communication intervals, and the capture register can record external events. Because the maximum supply voltage is 5.00 V, analog and digital interfaces require suitable scaling and isolation. Check signal-conditioning accuracy, sampling latency, external memory access time, and grounding in the completed instrument.
推荐
Communications Controller
The Z86C9325FSC is applicable to established communications-controller designs that use the Z8 core, external program memory, and deterministic peripheral timing. The 25 MHz clock can support protocol and framing routines, while SCLK, IACK, SYNC, and WAIT signals provide the basis for coordinated bus transactions. Three 16-bit timers can support baud-rate generation, timeout handling, and frame timing, while the hardware multiplier assists with checksums and data manipulation. The ROMless architecture is useful when firmware needs external storage, although program-memory access time must be included in timing analysis. Verify signal timing, bus direction, interrupt behavior, and electrical levels against the original design.
推荐
Embedded Data Acquisition
The Z86C9325FSC fits a legacy embedded acquisition system when the controller must coordinate converters, memory, and data processing around a compact 8-bit architecture. Its three 16-bit timers can sequence sampling and conversion intervals, and the capture register can capture external timing references. The dedicated multiplier and divider assist with gain, offset, scaling, and statistical calculations, while the 25 MHz clock allows firmware to service multiple peripheral events. External program and data memory are mandatory elements of the ROMless design. Engineers should verify acquisition timing, memory wait states, interrupt latency, analog input conditioning, and the board's 5.00 V power budget.
推荐
Appliance and Service Electronics
The Z86C9325FSC is useful for repair and continuation designs in legacy appliance and service electronics where an existing 44-QFP control board already uses the Z86C93 architecture. The dedicated multiplier, divider, and three timers support motor timing, state sequencing, and load-related calculations without requiring a redesign of the original firmware. Because the MCU is ROMless, replacement hardware must be accompanied by the correct external program-memory arrangement and loading process. A service engineer should verify the complete ordering suffix, temperature grade, supply tolerance, external memory timing, and every board-level signal before replacing the original controller.
推荐
推荐产品汇总
工程参考数据: Z86C9325FSC ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | Z86C9325FSG |
|---|---|---|
| Package | QFP-44 | QFP-44 |
| Brand | Zilog | Zilog |
| Device Type | 8-bit ROMless microcontroller | 8-bit ROMless microcontroller |
| Maximum Clock Frequency | 25 MHz | 25 MHz |
| Architecture | Z8 | Z8 |
| Maximum Supply Voltage | 5.00 V | 5.00 V maximum |
| Mounting Style | Surface mount | Surface mount |
关键差异点
- Dedicated arithmetic hardware supports efficient 8-bit embedded control (对比 General-purpose 8-bit microcontrollers without equivalent hardwired blocks)
- Three dedicated timing channels support concurrent embedded-control tasks (对比 Single-timer or timer-limited general-purpose 8-bit controllers)
- Established Z8 ROMless architecture preserves legacy firmware and external-memory designs (对比 Newer MCU families requiring a different instruction set and toolchain)
- A confirmed same-package ordering option exists for the 44-QFP footprint (对比 Z86C9325FSG)
设计说明
Design the 5.00 V supply rail with local high-frequency decoupling placed directly beside the controller's supply and ground connections. The ROMless MCU depends on external memory, which may contribute substantial switching current during bus activity. Separate analog and digital return paths where the board supports mixed-signal measurement. Confirm supply tolerance, startup sequencing, and the voltage present on every controller and memory pin because the Z86C9325FSC's identified maximum supply rating is 5.00 V.
Preserve the established 44-QFP land pattern and verify pin 1 orientation against the manufacturer's package drawing before releasing artwork. External program memory, data memory, address lines, and control signals must follow the Z86C93 bus requirements. Place decoupling and any memory devices close to their associated controller pins, and avoid routing the external bus through long unprotected branches. A footprint derived from terminal count alone is insufficient because land width, pitch, span, and pin-1 orientation must match the specified package.
Do not treat a controller with the same Z8 family name as a drop-in replacement without checking the package, clock rating, memory organization, ordering suffix, and temperature grade. The confirmed same-package candidate is the Z86C9325FSG, whose 44-QFP format and 25 MHz rating align with the target. Firmware also depends on external memory and device-specific bus timing. Validate startup vectors, wait-state behavior, interrupt sources, peripheral addresses, and programming procedure before installing a substitute.
Review external-memory access timing as part of the processor design rather than treating the 25 MHz CPU clock as the only timing constraint. Address, data, and control lines should have short, continuous return paths, and the board should avoid stubs or unnecessary test-probe branches. If the design includes synchronous external devices, verify setup and hold margins across temperature and supply tolerances. The controller's hardwired arithmetic reduces computation time but does not remove the electrical timing requirements of the external bus.
合规信息
No exact-suffix environmental or automotive compliance declaration was identified. The commercial temperature-grade classification does not by itself establish RoHS, REACH, or AEC-Q100 status. Request the current compliance documentation for the exact MPN through the Request a Quote form.