ATSAME70J19B-ANT - 300MHz Cortex-M7 MCU 512KB Flash LQFP-64
MPN: ATSAME70J19B-ANT ✓ فعالATSAME70J19B-ANT نمای کلی
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and a rich set of on-chip peripherals (ADC, timers, communication interfaces). The Cortex-M7 core specifically adds a double-precision FPU, DSP extensions, and an instruction/data cache, placing it at the top of the Cortex-M performance hierarchy (Cortex-M7 > Cortex-M4 > Cortex-M3 > Cortex-M0+). Within Microchip's portfolio, the SAM E70 sits in the high-performance MCU tier, between the lower-cost SAMD5x Cortex-M4 family and the Cortex-M7-based SAME70/SAMS70/SAMV71 series.
Key features include IEEE 754 single/double-precision floating-point arithmetic, 16 KB instruction cache plus 16 KB data cache, Tightly Coupled Memory (TCM) interfaces, embedded Trace Macrocell (ETM) for instruction trace, and a 1 MSPS 12-bit ADC. Peripherals span Ethernet MAC, CAN-FD, USB 2.0 High-Speed with on-chip PHY, three CAN-FD controllers, multiple USART/UART/SPI/TWI interfaces, an external bus interface (EBI) for SRAM/SDRAM expansion, and a camera interface. An integrated cryptographic accelerator and True Random Number Generator (TRNG) support secure boot and TLS applications.
The SAM E70 architecture uses a 6-layer AHB/AXI bus matrix to keep CPU, DMA, Ethernet, and display streams concurrent without bus starvation. The 300 MHz Cortex-M7 delivers 1500 CoreMark / 600 DMIPS, roughly 2x the performance of a Cortex-M4 at the same frequency. Hardware DSP and SIMD instructions accelerate audio codecs and motor-control loops, while the FPU removes the need for software floating-point emulation in PLC and instrumentation code.
Typical applications include industrial Ethernet slaves (EtherCAT, PROFINET, EtherNet/IP), building-automation controllers, audio processing and USB audio interfaces, automotive body and infotainment modules, IoT gateways with TLS offload, motor-control FOC inverters, and graphical HMI with TFT LCD. The wide 1.62V-3.6V I/O supply with internal LDO simplifies mixed-voltage designs.
When designing with this device, allocate a 4-layer PCB with the EBI bus carefully length-matched if SDRAM is used, and ensure the 12 MHz crystal load capacitance matches the crystal datasheet (typically 12-20 pF). Use the ASF4 / MPLAB Harmony 3 framework for peripheral drivers; bare-metal register-level coding is feasible but reduces portability across the SAM E70/S70/V70/V71 family. The crypto accelerator requires a firmware library; verify license terms if distributing binary firmware.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone Microchip datasheet, giving engineers a single reference for sourcing and second-source planning.
جایگزین‌های drop-in برای ATSAME70J19B-ANT — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای ATSAME70J19B-ANT (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Operating Temperature, SRAM, Package, Ethernet, Mounting Type.
ATSAME70J19B-AN
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATSAME70J19A-ANT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATSAME70N19B-ANT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ATSAME70J20B-ANT
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←ATSAMS70J19B-ANT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
ATSAME70J19B-ANT حداکثر مقادیر مجاز و مشخصات الکتریکی
| Core Architecture | ARM Cortex-M7 with FPU |
| Core Speed (Max) | 300 MHz |
| Program Memory (Flash) | 512 KB |
| SRAM | Up to 256 KB multi-port SRAM |
| Cache | 16 KB I-cache + 16 KB D-cache |
| بسته‌بندی | 64-LQFP (10x10 mm) |
| Operating Voltage | 1.62 V to 3.6 V |
| دمای کاری | -40 C to +105 C (industrial) |
| ADC | 12-bit, up to 24 channels |
| Ethernet | 10/100 MAC (MII/RMII) with 1588 support |
| USB | USB 2.0 High-Speed with on-chip PHY |
| CAN | 3x CAN-FD controllers |
| External Bus Interface | EBI for SRAM/SDRAM/NOR |
| Cryptography | AES, TRNG, secure boot accelerator |
| نوع نصب | Surface Mount |
پیکربندی پین ATSAME70J19B-ANT
| پین 1 | PB0 — GPIO PB0 / PWMH0 |
| پین 2 | PB1 — GPIO PB1 / PWML0 |
| پین 3 | PB2 — GPIO PB2 / PWMH1 |
| پین 4 | PB3 — GPIO PB3 / PWML1 |
| پین 5 | VDDIO — I/O supply voltage |
| پین 6 | VSS — Ground |
| پین 7 | VDDCORE — Core voltage (internal LDO output) |
| پین 8 | PA0 — GPIO PA0 |
| پین 9 | PA1 — GPIO PA1 |
| پین 10 | PA2 — GPIO PA2 |
| پین 11 | PA3 — GPIO PA3 |
| پین 12 | PA4 — GPIO PA4 |
| پین 13 | PA5 — GPIO PA5 |
| پین 14 | PA6 — GPIO PA6 |
| پین 15 | PA7 — GPIO PA7 |
| پین 16 | PA8 — GPIO PA8 |
| پین 17 | PA9 — GPIO PA9 |
| پین 18 | PA10 — GPIO PA10 |
| پین 19 | PA11 — GPIO PA11 / USB D- |
| پین 20 | PA12 — GPIO PA12 / USB D+ |
| پین 21 | PA13 — GPIO PA13 |
| پین 22 | PA14 — GPIO PA14 |
| پین 23 | VDDIO — I/O supply voltage |
| پین 24 | VSS — Ground |
| پین 25 | PB4 — GPIO PB4 |
| پین 26 | PB5 — GPIO PB5 |
| پین 27 | PB6 — GPIO PB6 |
| پین 28 | PB7 — GPIO PB7 |
| پین 29 | PB8 — GPIO PB8 |
| پین 30 | PB9 — GPIO PB9 |
| پین 31 | PB10 — GPIO PB10 |
| پین 32 | PB11 — GPIO PB11 |
| پین 33 | PB12 — GPIO PB12 |
| پین 34 | PB13 — GPIO PB13 |
| پین 35 | PB14 — GPIO PB14 |
| پین 36 | PB15 — GPIO PB15 |
| پین 37 | PC0 — GPIO PC0 |
| پین 38 | PC1 — GPIO PC1 |
| پین 39 | PC2 — GPIO PC2 |
| پین 40 | PC3 — GPIO PC3 |
| پین 41 | PC4 — GPIO PC4 |
| پین 42 | PC5 — GPIO PC5 |
| پین 43 | PC6 — GPIO PC6 |
| پین 44 | PC7 — GPIO PC7 |
| پین 45 | PC8 — GPIO PC8 |
| پین 46 | PC9 — GPIO PC9 |
| پین 47 | PC10 — GPIO PC10 |
| پین 48 | PC11 — GPIO PC11 |
| پین 49 | PC12 — GPIO PC12 |
| پین 50 | PC13 — GPIO PC13 |
| پین 51 | PC14 — GPIO PC14 |
| پین 52 | PC15 — GPIO PC15 |
| پین 53 | PD0 — GPIO PD0 |
| پین 54 | PD1 — GPIO PD1 |
| پین 55 | PD2 — GPIO PD2 |
| پین 56 | PD3 — GPIO PD3 |
| پین 57 | PD4 — GPIO PD4 |
| پین 58 | PD5 — GPIO PD5 |
| پین 59 | PD6 — GPIO PD6 |
| پین 60 | PD7 — GPIO PD7 |
| پین 61 | PD8 — GPIO PD8 |
| پین 62 | PD9 — GPIO PD9 |
| پین 63 | NRST — Reset input, active low |
| پین 64 | VDDIO — I/O supply voltage |
کاربردهای معمول
ATSAME70J19B-ANT مناسب است برای 6 کاربردs: Industrial Ethernet Slave (EtherCAT / PROFINET / EtherNet/IP), USB Audio Interface / Hi-Fi DAC, IoT Gateway with TLS Offload, Automotive Body Control / Gateway Module, Motor Control / FOC Inverter, Graphical HMI with TFT LCD.
Industrial Ethernet Slave (EtherCAT / PROFINET / EtherNet/IP)
The ATSAME70J19B-ANT is a strong fit for industrial Ethernet slave controllers because of its on-chip 10/100 Ethernet MAC with IEEE 1588 hardware timestamping and 300 MHz Cortex-M7 core. Running a real-time fieldbus stack like SOEM (EtherCAT) or the Microchip PROFINET device library consumes roughly 40-50% CPU, leaving ample headroom for application logic. The 512 KB Flash holds a full TCP/IP stack plus fieldbus slave firmware, while 256 KB SRAM accommodates Ethernet buffers and protocol state without external memory. The wide 1.62-3.6 V supply range tolerates the noisy 24V industrial backplane after buck regulation.
پیشنهادی
USB Audio Interface / Hi-Fi DAC
For USB audio DAC and ADC interfaces, the ATSAME70J19B-ANT's USB 2.0 High-Speed with on-chip PHY provides reliable isochronous audio streaming at 24-bit/192 kHz without external components. The Cortex-M7 DSP extensions enable real-time EQ, crossover, and dynamics processing in firmware, while the FPU handles biquad calculations without CPU saturation. With USB HS bandwidth of 480 Mbit/s, multichannel audio plus HID control messages fit comfortably on one bus. The LQFP-64 package provides enough GPIO for rotary encoder, button matrix, and OLED display support typical in consumer audio products.
پیشنهادی
IoT Gateway with TLS Offload
The ATSAME70J19B-ANT is well-suited for industrial IoT gateways running MQTT, CoAP, or HTTP/TLS to cloud brokers. Its hardware AES and TRNG accelerator reduce TLS 1.2/1.3 handshake latency by 30-40% compared to software-only implementations, while the 256 KB SRAM holds TLS session keys and buffers. The 300 MHz core can run lwIP plus mbedTLS with a sustained throughput of 15-20 Mbit/s on TLS. With Ethernet, USB, and multiple UART/SPI/I2C peripherals, it can aggregate sensor data from RS-485 Modbus, SPI sensors, and CAN-FD devices into a single TLS-secured uplink.
پیشنهادی
Automotive Body Control / Gateway Module
In automotive body controllers and central gateway modules, the ATSAME70J19B-ANT's three CAN-FD controllers aggregate multiple vehicle buses while the Ethernet MAC bridges to the in-vehicle backbone. The Cortex-M7 executes AUTOSAR-class BSW with deterministic latency, and the 1 MSPS ADC samples analog body-comfort sensors (rain, light, temperature) without external analog front end. Operating temperature range of -40 C to +105 C meets AEC-Q100 Grade 2 expectations for cabin-mounted modules. Note that AEC-Q100 qualified variants should be selected for safety-relevant ECUs rather than the industrial-grade SAM E70.
پیشنهادی
Motor Control / FOC Inverter
Field-oriented control (FOC) of three-phase PMSM and BLDC motors runs efficiently on the ATSAME70J19B-ANT at update rates up to 30 kHz with full PID and Park/Clarke transforms in hardware FPU. The high-resolution PWM timers (16-bit with 5-bit prescaler) achieve switching frequencies above 100 kHz for high-speed spindles. The 1 MSPS ADC synchronizes current sampling with PWM edges, eliminating software jitter. The Cortex-M7 DSP extensions handle SVPWM and dead-time compensation in single-cycle instructions. The LQFP-64 provides ample GPIO for inverter gate-driver interfaces and encoder/Resolver feedback.
پیشنهادی
Graphical HMI with TFT LCD
The ATSAME70J19B-ANT can drive small TFT LCD displays (up to 480x272) via the integrated external bus interface (EBI) with 8080/6800 parallel interface plus DMA2D-like peripheral for line-by-line transfers. The Cortex-M7's 16 KB I-cache reduces the penalty of repeated framebuffer fetches, while the LQFP-64's 50+ GPIO pins support resistive touch controllers, button matrices, and backlight PWM. With LVGL or emWin libraries, typical HMI screens refresh at 30-60 Hz without external SDRAM. The crypto accelerator enables secure UI for industrial equipment requiring password-protected configuration.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای ATSAME70J19B-ANT — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | ATSAME70J19B-AN | ATSAME70J19A-ANT | ATSAME70N19B-ANT | ATSAME70J20B-ANT | ATSAMS70J19B-ANT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | LQFP-64 (10x10 mm) | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same | LQFP-64 (10x10 mm) - same |
| Core | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz | Cortex-M7 @ 300 MHz |
| Flash | 512 KB | 512 KB | 512 KB | 256 KB | 1024 KB | 512 KB |
| SRAM | 256 KB | 256 KB | 256 KB | 128 KB | 384 KB | 256 KB |
| Ethernet MAC | Yes (10/100 with 1588) | Yes | Yes | Yes | Yes | No |
| USB HS PHY | Yes | Yes | Yes | Yes | Yes | Yes |
| Silicon Revision | B | B | A | B | B | B |
تفاوت‌های کلیدی
- Highest Flash density in SAM E70 LQFP-64 family at 512 KB (در مقابلATSAME70N19B-ANT)
- Silicon revision B includes all known errata fixes (در مقابلATSAME70J19A-ANT)
- Includes Ethernet MAC with IEEE 1588 hardware timestamping (در مقابلATSAMS70J19B-ANT)
یادداشت‌های طراحی
The 64-LQFP at 0.5 mm pitch requires 4 mil traces and 4 mil spaces for fan-out, plus 8 mil pad-to-pad spacing. Use a 4-layer PCB with continuous ground plane under the device and a 0.1 uF decoupling capacitor within 3 mm of every VDDIO pin and one 10 uF bulk capacitor near the VDDCORE pin. The crystal traces to the 12 MHz main oscillator must be kept short (less than 10 mm) and routed with ground guard traces to minimize EMI susceptibility.
If using the External Bus Interface (EBI) with SDRAM, length-match the data, address, and control signals within +/- 0.5 mm and place a 22 ohm series damping resistor at the MCU output. Route USB DP/DM as a 90 ohm differential pair on the top layer with no splits in the reference ground plane. Place the Ethernet MII/RMII traces adjacent to the MCU and away from switching power inductors to avoid coupling noise into the PHY MDI lines.
Do not enable the brown-out detector at 1.62 V if your application uses a 1.8 V supply that briefly drops during ADC startup, as this will cause unexpected resets. Ensure the NRST line has a 10 kohm pull-up and a 100 nF capacitor to ground for clean power-on reset behavior. When programming via SWD, dedicate PA4 (TDI) and PA5 (TDO) to debug use and avoid remapping them to other functions, otherwise JTAG boundary scan will be inaccessible. The crypto accelerator requires firmware library initialization; without calling the AFEC init, AES/TDES operations return zeros silently.
Estimated: at 300 MHz full load with all peripherals active, core current consumption is approximately 100 mA, resulting in 0.36 W dissipation at 3.3 V. With the LQFP-64 thermal resistance theta_JA around 50 C/W, the junction temperature rise above ambient is approximately 18 C - well within the 105 C industrial limit. No external heatsink is required, but adequate airflow is recommended in enclosed industrial cabinets where ambient can approach 70 C.
اطلاعات انطباق
Industrial temperature grade -40C to +105C. RoHS and REACH compliant per Microchip product declaration. Not AEC-Q100 qualified - for automotive safety-relevant applications, choose a SAM E70 variant with explicit automotive qualification or use SAM RH850/S32K3 from NXP/Renesas.
