DS90LV110TMTCX - 400MHz 1:10 LVDS Clock Distributor | TI
MPN: DS90LV110TMTCX ✓ نشطDS90LV110TMTCX نظرة عامة
An LVDS data or clock distributor is a specialized interface IC that converts one differential input into multiple low-voltage differential outputs. Within the interface-IC hierarchy, the DS90LV110T belongs to the clock-buffer and fanout-buffer family, using Low Voltage Differential Signaling to support high data rates while limiting signal noise and electromagnetic emissions. Differential signaling also provides common-mode noise rejection in systems where the source and receiver share a ground reference.
Key features include a 1:10 fanout ratio, 400 MHz maximum clock frequency, and 800 Mbps data rate. The outputs can enter a tri-state condition through the enable function described by the manufacturer, allowing unused branches to be disabled when system power management or bus contention requires it. A 28-pin TSSOP package supports compact board layouts in industrial-grade equipment.
The fully differential signal path is intended to preserve low-noise operation and minimize pulse-width distortion from input to output. This makes the distributor useful when a high-speed clock, control signal, or serialized data stream must reach multiple devices without introducing a separate transmission-line segment for every destination. Its operating range covers industrial ambient conditions from -40°C through +85°C.
Typical applications include industrial control and instrumentation backplanes, test and measurement systems, computer and telecommunications clock distribution, and multi-drop LVDS communication links. The 10-output arrangement reduces the number of separate fanout devices required when several endpoints share a common source.
PCB design should preserve controlled-impedance differential routing, minimize stub lengths, and place termination close to the receiving device. Designers should also account for the voltage loss between the distributor and each receiver, particularly at 800 Mbps, and confirm that every enabled LVDS output has a valid termination path.
بدائل مباشرة لـ DS90LV110TMTCX — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع DS90LV110TMTCX (نفس عامل الشكل والبصمة) — يختلف في Mounting Type.
DS90LV110TMTC
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DS90LV110TMTCX/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90LV110ATMT/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MAX9150EUI+
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MAX9150EUI+T
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90LV110TMTCX المواصفات
| Product Type | 1-to-10 LVDS data/clock distributor |
| Fanout Ratio | 1:10 |
| أقصى تردد للساعة | 400 MHz |
| Maximum Data Rate | 800 Mbps |
| Input Logic | LVDS differential input |
| Output Logic | 10 LVDS differential outputs |
| Output Enable | Tri-state output enable |
| Input Common-Mode Voltage | 0.45 V |
| نطاق درجة حرارة التشغيل | -40°C to +85°C |
| العلبة | 28-pin TSSOP |
| Package Width | 4.40 mm |
| نوع التركيب | Surface mount |
| Temperature Grade | Industrial grade |
| Terminal Count | 28 terminals |
| حالة RoHS | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
دليل تكوين أطراف DS90LV110TMTCX 4.40 mm
تكوين الأطراف لـ DS90LV110TMTCX (حزمة 4.40 mm). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DS90LV110TMTCX.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
DS90LV110TMTCX مناسب لـ 6 التطبيقs: Industrial Clock Distribution, Test and Measurement Systems, Telecommunications Backplanes, Multi-Sensor Data Acquisition, Audio and Video Equipment, Server and Storage Clock Networks.
Industrial Clock Distribution
The DS90LV110TMTCX fits industrial backplanes that require one differential clock to reach up to ten controller or instrumentation endpoints. Its 1:10 fanout avoids cascaded clock buffers, which can add skew and reduce design margin. The confirmed 400 MHz clock capability supports high-speed control and measurement subsystems, while the -40°C to +85°C range suits industrial ambient conditions. Use controlled-impedance differential traces, place terminations at the receivers, and keep branches short to prevent reflections. Designers should also verify the distributor’s supply requirements and timing budget against the system clock before release.
موصى به
Test and Measurement Systems
The DS90LV110TMTCX is well suited to instrument and test-system clock trees where a low-skew source must feed several acquisition, triggering, or processing blocks. Ten LVDS outputs support multiple endpoints without requiring a separate fanout buffer at every branch, and the 400 MHz rating covers demanding baseband and digitization clock requirements. Keep each differential pair impedance controlled and terminate the far end of every enabled output. For sensitive analog channels, isolate the distributor from switching supplies and preserve a continuous ground reference so common-mode noise does not degrade the differential clock.
موصى به
Telecommunications Backplanes
The DS90LV110TMTCX can distribute a 400 MHz differential clock across ten communications endpoints in a telecommunications or networking chassis. Its ten LVDS outputs reduce the component count compared with cascaded fanout stages, while differential signaling supports reliable operation over PCB interconnects. The -40°C to +85°C range accommodates industrial networking equipment. Designers should preserve pair symmetry, minimize vias and stubs, and use receiver-end termination appropriate for the cable or PCB length. Supply decoupling and ground-plane continuity are especially important when the distributor shares a board with switching regulators or high-current backplane circuitry.
موصى به
Multi-Sensor Data Acquisition
The DS90LV110TMTCX fits acquisition systems where a common sampling or synchronization clock must reach multiple sensors, digitizers, or field devices. Its 1:10 fanout allows one low-voltage differential source to support as many as ten endpoints, while operation to 400 MHz supports high-speed sampling architectures. Keep the clock path physically short and symmetric to limit skew between channels, and check lane-to-lane timing at the receiver rather than assuming perfect matching. The industrial temperature range supports factory-floor equipment when the enclosure does not exceed the specified ambient range.
موصى به
Audio and Video Equipment
The DS90LV110TMTCX can serve as a clock or synchronization distributor in professional audio, video, and broadcast equipment that requires several differential endpoints. Its 400 MHz capability exceeds typical audio clock rates while providing a path for related high-speed control data, and the ten-output topology reduces the number of separate buffers in complex chassis. Because the distributor is not itself a precision low-noise regulator, analog audio rails should remain separate. Use short LVDS routes, maintain solid reference planes, and avoid sharing noisy return paths with switching converters or display power stages.
موصى به
Server and Storage Clock Networks
The DS90LV110TMTCX is applicable to server, storage, and accelerator boards that distribute a high-speed differential clock to multiple local circuits. The 1:10 ratio can reduce fanout depth and preserve timing margin in compact systems, while the 28-TSSOP package supports conventional surface-mount assembly. At rates as high as 800 Mbps, the PCB must use continuous differential impedance and avoid unterminated test pads. The component’s -40°C to +85°C rating suits many industrial server environments, but server designers should also verify power sequencing, clock amplitude, and lane-level timing at every receiver.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DS90LV110TMTCX — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DS90LV110TMTC | DS90LV110TMTCX/NOPB | DS90LV110ATMT/NOPB | MAX9150EUI+ | MAX9150EUI+T |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices | Analog Devices |
| Package | 28-TSSOP | 28-TSSOP - same | 28-TSSOP - same | 28-TSSOP - same | 28-TSSOP - same | 28-TSSOP - same |
| Product Type | LVDS data/clock distributor | Clock fanout buffer / LVDS distributor | LVDS data/clock distributor | LVDS data/clock distributor | Similar 1-to-10 LVDS distributor | Similar 1-to-10 LVDS distributor |
| Fanout Ratio | 1:10 | 1:10 | 1:10 | 1:10 | 1:10 | 1:10 |
أبرز الفروقات
- Higher confirmed clock frequency than the listed MAX9150 alternatives (مقابلMAX9150EUI+)
- Single-stage distribution to ten endpoints (مقابلDS90LV110ATMT/NOPB)
- Directly identified manufacturer-ordering alternative (مقابلDS90LV110TMTC)
ملاحظات التصميم
Treat every enabled LVDS branch as a controlled-impedance differential transmission line. Use matched pair spacing, a continuous reference plane, minimal vias, and no long test-point stubs. The distributor can operate at 800 Mbps, so discontinuities that are acceptable at low clock rates may produce reflections or timing degradation at this rate. Confirm input and output impedance assumptions against the manufacturer interface recommendations.
Place input and output bypass capacitors close to their associated supply and ground pins, and keep the LVDS routes away from switching nodes and high-current return paths. Differential signals should reference the same uninterrupted plane where possible. When multiple outputs fan out, preserve symmetric geometry so propagation-delay differences remain small and receiver-to-receiver clock skew does not exceed the system budget.
Do not assume that every 28-pin LVDS distributor is pin-compatible. The DS90LV110TMTCX, DS90LV110TMTC, DS90LV110TMTCX/NOPB, DS90LV110ATMT/NOPB, MAX9150EUI+, and MAX9150EUI+T appear in the same-package comparison, but enable polarity, supply voltage, output timing, and input common-mode limits still require direct datasheet comparison before substitution.
Use the supply-decoupling network and bypass placement specified for the DS90LV110T family. Because the device is a high-speed distributor, supply-return impedance and ground bounce can perturb differential signal amplitude even when nominal voltage remains correct. Provide stable local power, route return current away from LVDS traces, and validate startup and enable transitions with the actual receiver configuration.
معلومات الامتثال
The accessible manufacturer and distributor excerpts do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this exact order code. AEC-Q100 is not applicable to this industrial interface IC unless the manufacturer identifies a separate automotive-qualified order code.