Texas Instruments

DS90LV110TMTCX - 400MHz 1:10 LVDS Clock Distributor | TI

부품 번호: DS90LV110TMTCX ✓ 활성
0.45 V Vdss 28-pin TSSOP Package 400 MHz Speed
MOQ: 1 |

DS90LV110TMTCX 개요

Texas Instruments DS90LV110TMTCX is a 1-to-10 LVDS data and clock distributor rated for operation up to 400 MHz and 800 Mbps in a 28-pin TSSOP package. It provides one differential input and ten differential LVDS outputs, with an operating-temperature range of -40°C to +85°C. The device is intended for low-power, high-speed signal distribution where a source must feed multiple balanced endpoints.

An LVDS data or clock distributor is a specialized interface IC that converts one differential input into multiple low-voltage differential outputs. Within the interface-IC hierarchy, the DS90LV110T belongs to the clock-buffer and fanout-buffer family, using Low Voltage Differential Signaling to support high data rates while limiting signal noise and electromagnetic emissions. Differential signaling also provides common-mode noise rejection in systems where the source and receiver share a ground reference.

Key features include a 1:10 fanout ratio, 400 MHz maximum clock frequency, and 800 Mbps data rate. The outputs can enter a tri-state condition through the enable function described by the manufacturer, allowing unused branches to be disabled when system power management or bus contention requires it. A 28-pin TSSOP package supports compact board layouts in industrial-grade equipment.

The fully differential signal path is intended to preserve low-noise operation and minimize pulse-width distortion from input to output. This makes the distributor useful when a high-speed clock, control signal, or serialized data stream must reach multiple devices without introducing a separate transmission-line segment for every destination. Its operating range covers industrial ambient conditions from -40°C through +85°C.

Typical applications include industrial control and instrumentation backplanes, test and measurement systems, computer and telecommunications clock distribution, and multi-drop LVDS communication links. The 10-output arrangement reduces the number of separate fanout devices required when several endpoints share a common source.

PCB design should preserve controlled-impedance differential routing, minimize stub lengths, and place termination close to the receiving device. Designers should also account for the voltage loss between the distributor and each receiver, particularly at 800 Mbps, and confirm that every enabled LVDS output has a valid termination path.

드롭인 대체품: DS90LV110TMTCX — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: DS90LV110TMTCX (동일 폼 팩터 및 풋프린트) — 차이점: Mounting Type.

Analog Devices
Mounting Type: Surface Mount (gull-wing)
비교 대상: DS90LV110TMTCX →

DS90LV110TMTC

✅ 드롭인
Texas Instruments
📦 28-TSSOP
LVDS data and clock distributor · 1:10 · 400 MHz · 1 input · 10 outputs · 10 · 1 · 3.3 V

가격 문의

데이터시트 보기 →

DS90LV110TMTCX/NOPB

✅ 드롭인
📦 28-TSSOP
Same 1:10 LVDS function and 28-pin TSSOP format; order-code or finish differences are not quantified in the technical excerpt.

📋 참조 대체품 (카탈로그에 없음)

DS90LV110ATMT/NOPB

✅ 드롭인
📦 28-TSSOP
Same DS90LV110A 1:10 LVDS family and 28-TSSOP format; revised silicon-generation timing and parameter differences require datasheet review.

📋 참조 대체품 (카탈로그에 없음)

MAX9150EUI+

✅ 드롭인
Analog Devices
📦 28-TSSOP
10-Port LVDS Repeater (Buffer/ReDriver) · 1 LVDS differential input · 10 LVDS differential outputs · 400 Mbps · 120 ps p-p max (deterministic and random) · 100 ps max · 60 uA · 160 mA

가격 문의

데이터시트 보기 →

MAX9150EUI+T

✅ 드롭인
📦 28-TSSOP
Similar 1:10 LVDS distributor with a 320 MHz class clock rating versus 400 MHz for DS90LV110TMTCX; lead-finish ordering code differs.

📋 참조 대체품 (카탈로그에 없음)

DS90LV110TMTCX 사양

Product Type 1-to-10 LVDS data/clock distributor
Fanout Ratio 1:10
최대 클록 주파수 400 MHz
Maximum Data Rate 800 Mbps
Input Logic LVDS differential input
Output Logic 10 LVDS differential outputs
Output Enable Tri-state output enable
Input Common-Mode Voltage 0.45 V
동작 온도 범위 -40°C to +85°C
패키지 28-pin TSSOP
Package Width 4.40 mm
실장 유형 Surface mount
Temperature Grade Industrial grade
Terminal Count 28 terminals
RoHS 상태 Unknown
REACH Status Unknown
AEC-Q100 Qualification Not applicable

DS90LV110TMTCX 4.40 mm 핀 구성 가이드

DS90LV110TMTCX(4.40 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

DS90LV110TMTCX의 4.40 mm 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: DS90LV110TMTCX.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

DS90LV110TMTCX 적합 용도: 6 애플리케이션s: Industrial Clock Distribution, Test and Measurement Systems, Telecommunications Backplanes, Multi-Sensor Data Acquisition, Audio and Video Equipment, Server and Storage Clock Networks.

🏭

Industrial Clock Distribution

The DS90LV110TMTCX fits industrial backplanes that require one differential clock to reach up to ten controller or instrumentation endpoints. Its 1:10 fanout avoids cascaded clock buffers, which can add skew and reduce design margin. The confirmed 400 MHz clock capability supports high-speed control and measurement subsystems, while the -40°C to +85°C range suits industrial ambient conditions. Use controlled-impedance differential traces, place terminations at the receivers, and keep branches short to prevent reflections. Designers should also verify the distributor’s supply requirements and timing budget against the system clock before release.

🔧

Test and Measurement Systems

The DS90LV110TMTCX is well suited to instrument and test-system clock trees where a low-skew source must feed several acquisition, triggering, or processing blocks. Ten LVDS outputs support multiple endpoints without requiring a separate fanout buffer at every branch, and the 400 MHz rating covers demanding baseband and digitization clock requirements. Keep each differential pair impedance controlled and terminate the far end of every enabled output. For sensitive analog channels, isolate the distributor from switching supplies and preserve a continuous ground reference so common-mode noise does not degrade the differential clock.

🌐

Telecommunications Backplanes

The DS90LV110TMTCX can distribute a 400 MHz differential clock across ten communications endpoints in a telecommunications or networking chassis. Its ten LVDS outputs reduce the component count compared with cascaded fanout stages, while differential signaling supports reliable operation over PCB interconnects. The -40°C to +85°C range accommodates industrial networking equipment. Designers should preserve pair symmetry, minimize vias and stubs, and use receiver-end termination appropriate for the cable or PCB length. Supply decoupling and ground-plane continuity are especially important when the distributor shares a board with switching regulators or high-current backplane circuitry.

🧩

Multi-Sensor Data Acquisition

The DS90LV110TMTCX fits acquisition systems where a common sampling or synchronization clock must reach multiple sensors, digitizers, or field devices. Its 1:10 fanout allows one low-voltage differential source to support as many as ten endpoints, while operation to 400 MHz supports high-speed sampling architectures. Keep the clock path physically short and symmetric to limit skew between channels, and check lane-to-lane timing at the receiver rather than assuming perfect matching. The industrial temperature range supports factory-floor equipment when the enclosure does not exceed the specified ambient range.

🎧

Audio and Video Equipment

The DS90LV110TMTCX can serve as a clock or synchronization distributor in professional audio, video, and broadcast equipment that requires several differential endpoints. Its 400 MHz capability exceeds typical audio clock rates while providing a path for related high-speed control data, and the ten-output topology reduces the number of separate buffers in complex chassis. Because the distributor is not itself a precision low-noise regulator, analog audio rails should remain separate. Use short LVDS routes, maintain solid reference planes, and avoid sharing noisy return paths with switching converters or display power stages.

🖥️

Server and Storage Clock Networks

The DS90LV110TMTCX is applicable to server, storage, and accelerator boards that distribute a high-speed differential clock to multiple local circuits. The 1:10 ratio can reduce fanout depth and preserve timing margin in compact systems, while the 28-TSSOP package supports conventional surface-mount assembly. At rates as high as 800 Mbps, the PCB must use continuous differential impedance and avoid unterminated test pads. The component’s -40°C to +85°C rating suits many industrial server environments, but server designers should also verify power sequencing, clock amplitude, and lane-level timing at every receiver.

What is the DS90LV110TMTCX?
The DS90LV110TMTCX is a Texas Instruments 1-to-10 LVDS data and clock distributor operating up to 400 MHz in a 28-pin TSSOP package. According to the manufacturer product page, the DS90LV110T family distributes one differential input across ten LVDS outputs, supports data rates up to 800 Mbps, and provides a tri-state output enable for controlling unused branches.
What is the operating voltage of DS90LV110TMTCX?
The DS90LV110TMTCX supply-voltage limits are not stated in the available manufacturer-page excerpt, so the exact operating range must be confirmed in the TI DS90LV110T datasheet before circuit design. The confirmed operating-temperature range is -40°C to +85°C. Use the datasheet power-supply recommendations and decoupling values rather than assuming a conventional 3.3 V or 5 V rail.
What is the maximum clock frequency of DS90LV110TMTCX?
The DS90LV110TMTCX supports clock frequencies up to 400 MHz. DigiKey identifies the exact device as a 1:10 clock fanout buffer with a 400 MHz maximum rating and a 28-TSSOP package. At this operating point, routing and termination quality become critical, so controlled-impedance traces, short stubs, and correctly placed differential terminations should be treated as mandatory layout requirements.
How many LVDS outputs does DS90LV110TMTCX provide?
The DS90LV110TMTCX provides ten differential LVDS outputs from one differential input, giving it a 1:10 fanout ratio. The Texas Instruments product page identifies the device as a 1-to-10 LVDS data/clock distributor. This arrangement is useful for feeding multiple balanced receivers from a common high-speed clock or serialized-data source while retaining a single compact fanout component.
What data rate does DS90LV110TMTCX support?
The DS90LV110TMTCX supports data rates up to 800 Mbps according to the product listing information. Its one differential input and ten LVDS outputs provide a low-power distribution path for high-speed industrial and communications links. Signal integrity at this rate depends on proper source and endpoint termination, controlled-impedance PCB routing, and minimizing connector or via discontinuities.
Where can I download the DS90LV110TMTCX datasheet PDF?
The official DS90LV110TMTCX technical information is available from the Texas Instruments DS90LV110T product page at https://www.ti.com/product/DS90LV110T. Open the datasheet link on that page for the electrical characteristics, pin configuration, recommended application circuit, and LVDS interface details. The DS90LV110TMTCX is an orderable member of the DS90LV110T family.
Where can I find the DS90LV110TMTCX pinout?
The DS90LV110TMTCX pinout should be taken from the pin-configuration table in the Texas Instruments DS90LV110T datasheet and the 28-pin TSSOP package drawing. The device uses 28 terminals and is not a simple SOIC pinout, so verify land geometry and terminal numbering before layout release. The accessible product excerpt confirms the package but does not reproduce individual pin names.
What can replace the DS90LV110TMTCX?
The closest directly documented alternatives are DS90LV110TMTC and DS90LV110TMTCX/NOPB from Texas Instruments, while MAX9150EUI+ and MAX9150EUI+T from Analog Devices are listed as similar 1-to-10 LVDS distributors. A replacement should be accepted only after comparing pin functions, supply voltage, output-enable behavior, timing, and package dimensions; the 28-pin TSSOP designation alone does not establish functional drop-in equivalence.
Can DS90LV110TMTCX/NOPB replace DS90LV110TMTCX?
DS90LV110TMTCX/NOPB is the closest documented same-manufacturer alternative and is identified as an LVDS 1-to-10 data/clock distributor in a 28-pin TSSOP package. However, the X and /NOPB order-code meanings are not fully described in the accessible technical excerpt. Confirm the complete ordering table and compare the pin and electrical tables before treating it as a production drop-in replacement.
Is DS90LV110TMTCX the same as MAX9150EUI+?
The DS90LV110TMTCX and MAX9150EUI+ are similar 1-to-10 LVDS distribution devices, but they are not proven identical by the available cross-reference data. The DS90LV110T family is specified for up to 400 MHz and 800 Mbps, while the MAX9150EUI+ part must be checked for its own speed, supply, pinout, enable behavior, and propagation-delay limits. Treat the MAX9150EUI+ as a redesign candidate until those details are matched.
DS90LV110TMTCX vs MAX9150EUI+ - which is better for a 400 MHz clock?
Choose the DS90LV110TMTCX when its documented 400 MHz and 800 Mbps ratings satisfy the clock tree, because those limits are confirmed for the TI family. Choose the MAX9150EUI+ only after its datasheet demonstrates equal or better timing performance and its pin functions match the PCB. The comparison must also account for input common-mode voltage, output enable polarity, supply level, and LVDS timing.
When should I choose DS90LV110TMTCX over a smaller clock buffer?
Choose the DS90LV110TMTCX when one differential source must reach as many as ten balanced endpoints and the design needs a supported rate of 400 MHz or 800 Mbps. A smaller 1-to-4 or 1-to-6 buffer is preferable when only a few branches are required because it can simplify routing and reduce board area. The TI device is preferable when its ten outputs and tri-state control reduce system complexity.
Is DS90LV110TMTCX suitable for industrial control systems?
The DS90LV110TMTCX is suitable for industrial-temperature operation from -40°C to +85°C and is listed as an industrial-grade part. Its ten LVDS outputs can distribute clocks or data across a control cabinet, instrumentation chassis, or factory test system. Ensure the enclosure, cable lengths, terminations, and ESD protection are appropriate for the installation environment.
How should DS90LV110TMTCX LVDS routing be designed?
Route the DS90LV110TMTCX differential input and outputs as controlled-impedance pairs with matched spacing and minimal stubs. Place the proper LVDS termination at the receiving end rather than splitting the signal arbitrarily, and keep clock or data traces away from noisy power-converter nodes. Because the distributor can operate at 800 Mbps, connector transitions and test points require return-path continuity and carefully controlled geometry.
Where to buy DS90LV110TMTCX and what is its price?
Use the Request a Quote form on this page to request current DS90LV110TMTCX pricing, stock, lead time, and minimum order quantity. The structured listing data does not contain a qualifying current quantity-break table, and the commercial status of each distribution channel can change without notice. The documented unit reference is maintained separately as an archived price and is not a guaranteed quotation.
What are the key specifications of DS90LV110TMTCX that engineers should know?
The key DS90LV110TMTCX specifications are a 1:10 fanout ratio, one differential input, ten LVDS outputs, a 400 MHz maximum clock frequency, an 800 Mbps maximum data rate, a 28-pin TSSOP package, and a -40°C to +85°C operating range. According to Texas Instruments, the outputs support tri-state operation through the enable function, making the device appropriate for multi-endpoint LVDS clock and data distribution.

엔지니어링 참조 데이터: DS90LV110TMTCX — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the DS90LV110TMTCX when a system requires one differential clock or data source to feed up to ten balanced endpoints at up to 400 MHz or 800 Mbps. Its industrial temperature range, tri-state output control, and 28-pin TSSOP format make it appropriate for instrument, industrial-control, networking, and communications clock trees. Consider DS90LV110TMTC when its order code is approved for the specific supply chain, and compare DS90LV110TMTCX/NOPB against the exact ordering and finish requirements before substitution. DS90LV110ATMT/NOPB may suit a revised silicon generation, but its timing and parameter deltas must be checked. The MAX9150EUI+ and MAX9150EUI+T are candidates only when their lower listed clock class is acceptable and their pin, enable, supply, and timing details match. For every alternative, validate differential impedance, terminations, propagation delay, and receiver compatibility rather than relying on package similarity alone.

대체품과의 비교

파라미터 이 제품 DS90LV110TMTC DS90LV110TMTCX/NOPB DS90LV110ATMT/NOPB MAX9150EUI+ MAX9150EUI+T
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Analog Devices Analog Devices
Package 28-TSSOP 28-TSSOP - same 28-TSSOP - same 28-TSSOP - same 28-TSSOP - same 28-TSSOP - same
Product Type LVDS data/clock distributor Clock fanout buffer / LVDS distributor LVDS data/clock distributor LVDS data/clock distributor Similar 1-to-10 LVDS distributor Similar 1-to-10 LVDS distributor
Fanout Ratio 1:10 1:10 1:10 1:10 1:10 1:10

주요 차별점

  • Higher confirmed clock frequency than the listed MAX9150 alternatives (vs MAX9150EUI+)
  • Single-stage distribution to ten endpoints (vs DS90LV110ATMT/NOPB)
  • Directly identified manufacturer-ordering alternative (vs DS90LV110TMTC)

설계 노트

Treat every enabled LVDS branch as a controlled-impedance differential transmission line. Use matched pair spacing, a continuous reference plane, minimal vias, and no long test-point stubs. The distributor can operate at 800 Mbps, so discontinuities that are acceptable at low clock rates may produce reflections or timing degradation at this rate. Confirm input and output impedance assumptions against the manufacturer interface recommendations.

Place input and output bypass capacitors close to their associated supply and ground pins, and keep the LVDS routes away from switching nodes and high-current return paths. Differential signals should reference the same uninterrupted plane where possible. When multiple outputs fan out, preserve symmetric geometry so propagation-delay differences remain small and receiver-to-receiver clock skew does not exceed the system budget.

Do not assume that every 28-pin LVDS distributor is pin-compatible. The DS90LV110TMTCX, DS90LV110TMTC, DS90LV110TMTCX/NOPB, DS90LV110ATMT/NOPB, MAX9150EUI+, and MAX9150EUI+T appear in the same-package comparison, but enable polarity, supply voltage, output timing, and input common-mode limits still require direct datasheet comparison before substitution.

Use the supply-decoupling network and bypass placement specified for the DS90LV110T family. Because the device is a high-speed distributor, supply-return impedance and ground bounce can perturb differential signal amplitude even when nominal voltage remains correct. Provide stable local power, route return current away from LVDS traces, and validate startup and enable transitions with the actual receiver configuration.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The accessible manufacturer and distributor excerpts do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for this exact order code. AEC-Q100 is not applicable to this industrial interface IC unless the manufacturer identifies a separate automotive-qualified order code.

데이터 검증일: 2026-11-16 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

ds90lv110tmtcx nopb DS90LV110TMTCX datasheet DS90LV110TMTCX datasheet pdf DS90LV110TMTCX pinout DS90LV110TMTCX equivalent DS90LV110TMTCX replacement DS90LV110TMTCX cross reference DS90LV110TMTCX vs MAX9150EUI+ Texas Instruments DS90LV110TMTCX DS90LV110TMTCX 400 MHz DS90LV110TMTCX 28-TSSOP DS90LV110TMTCX price DS90LV110TMTCX stock DS90LV110TMTCX clock distributor

관련 부품 & 용어

Texas Instruments DS90LV110TMTCX DS90LV110TMTC DS90LV110TMTCX/NOPB DS90LV110ATMT/NOPB MAX9150EUI+ MAX9150EUI+T LVDS Low Voltage Differential Signaling clock fanout buffer data distributor interface IC clock buffer 1:10 fanout 400 MHz 800 Mbps tri-state enable 28-TSSOP TSSOP package family surface mount industrial-grade semiconductor differential signaling controlled impedance LVDS termination common-mode noise rejection
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기